Concept explainers
6-51* to 6-53* For the problem specified in the table, build upon the results of the original problem to deter-mine the minimum factor of safety for fatigue at point A, based on infinite life, using the modified Goodman criterion. If the life is not infinite, estimate the number of cycles. The force F is applied as a repeated load. The material is AISI 1018 CD steel.
Problem Number | Original Problem, Page Number |
6-53* | 3-86, 155 |
3-86* Repeat Prob. 3-84 with Fx = 300 Ibf, Fy = 250 Ibf. and Fz = −100 Ibf.
3-84* The cantilevered bar in the figure is made from a ductile material and is statically loaded with Fy = 250 Ibf and Fx = Fz = 0. Analyze the stress situation in the small diameter at the shoulder at A by obtaining the following information.
- (a) Determine the precise location of the critical stress element at the cross section at A.
- (b) Sketch the critical stress clement and determine magnitudes and directions for all stresses acting on it. (Transverse shear may be neglected if you can justify this decision.)
- (c) For the critical stress clement, determine the principal stresses and the maximum shear stress.
Want to see the full answer?
Check out a sample textbook solutionChapter 6 Solutions
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
- Carbon Steel L=100mm dsmall= 20mm moment of inertia ratio between stepped cross-sectional area = 1:2 F=2500 N at A and a fillet radius at the step of 2mm -loading cycles that the design can withstand before fatigue failure - calculate cycles using goodman line and max stress from static analysis. -determine the effect of the 2mm fillet ratio on the fatigue analyisis. constant force at Aarrow_forwardThe cold-drawn AISI 1040 steel bar shown in the figure is subjected to a completely reversed axial load fluctuating between 15 kN in compression to 15 kN in tension. Estimate the fatigue factor of safety based on achieving infinite life, and the yielding factor of safety. If infinite life is not predicted, estimate the number of cycles to failure. 6 mm D. 25 mm 10 mmarrow_forwardThe figure shows a shaft mounted in bearings at A and D and having pulleys at B and C. The forces shown acting on the pulley surfaces represent the belt tensions. The shaft is to be made of AISI 1035 CD steel. The shaft is rotating at speed of 1000 rpm. Find the minimum factor of safety for fatigue based on infinite life. If the life is not infinite, estimate the number of cycles. Be sure to check for yielding. Take shaft diameter to be 1.5 inches.arrow_forward
- Required information The cold-drawn AISI 1040 steel bar shown in the figure is subjected to an axial load that fluctuates from 8 kN to 30 kN. Use the Modified Goodman criterion and estimate the fatigue factor of safety based on achieving infinite life and the yielding factor of safety. 25 mm 10mm -6-mm D. What is the number of cycles to failure for this part? The number of cycles is 120000arrow_forward3. The cold-drawn AISI 1040 steel plate shown in the figure below is subjected to a load that fluctuates from 12 kN to 28 kN. Estimate the fatigue factor of safety on achieving infinite life and the factor of safety guarding against first-cycle yielding. For fatigue analysis, use: 1) Goodman; 2) Morrow. 6-mm D. 25 mm 10 mmarrow_forward6-28 The figure shows a formed round-wire cantilever spring subjected to a varying force. The hardness tests made on 50 springs gave a minimum hardness of 400 Brinell. It is apparent from the mounting details that there is no stress concentration. A visual inspection of the springs indicates that the surface finish corresponds closely to a hot- rolled finish. Ignore curvature effects on the bending stress. What number of applica- tions is likely to cause failure? Solve using: (a) Goodman criterion. (b) Gerber criterion. = 40 lbf max 12 in- = 20 lbf min Problem 6-28arrow_forward
- The cold-drawn AISI 1040 Q&T at 205 ◦C steel bar shown in the figure is subjected to a completely reversed axial load fluctuating between 28 kN in compression to 28 kN in tension. Estimate the fatigue factor of safety based on achieving infinite life, and the yielding factor of safety for the following cases. If infinite life is not predicted, estimate the number of cycles to failure.a) for the part given in Fig 2(a) and b) for the part given in Fig. 2 (b) using the same dimensions (W=25mm, r=3mm, the thickness of 10 mm)arrow_forwardA pushrod in the valve mechanism of an automotive engine has a nominal length of 203 mm. If the rod is made of SAE 4140 steel, compute the elongation due to a temperature change from -20°C to 140°C. TABLE 3-4 Coefficients of thermal expansion, a, for some t nd concrretearrow_forwardA solid round bar with diameter of 2 in has a groove cut to a diameter of 1.8 in, with a radius of 0.1 in. The bar is not rotating. The bar is loaded with a repeated bending load that causes the bending moment at the groove to fluctuate between 0 and 25 000 lbf in. The bar is hot-rolled AISI 1095, but the groove has been machined. Determine the factor of safety for fatigue based on infinite life and the factor of safety for yielding. Plars & .arrow_forward
- A solid round bar with diameter of 2 in has a groove cut to a diameter of 1.8 in, with a radius of 0.1 in. The bar is not rotating. The bar is loaded with a repeated bending load that causes the bending moment at the groove to fluctuate between 0 and 25 000 lbf in. The bar is hot-rolled AISI 1095, but the groove has been machined. Determine the factor of safety for fatigue based on infinite life and the factor of safety for yielding. .arrow_forward1. A rotating l-in diameter solid round bar has a groove 0.1-in deep with a 0.1-radius machined into it. The bar is made of AISI 1020 CD steel and is subjected to a purely reversing torque of 1800 lbf-in. For the S-N curve of the material, let f= 0.9. 1) Estimate the number of cycles to failure. 2) If the bar is also placed in an environment with a temperature of 750 °F, estimate the number of cycles to failure. Note: for pure shear stress state, find ta and Tm to replace oa and om. Apply the load factor k. = 0.59. To get safety factor against first-cycle yielding, use Sgy=0.577 Sy (based on DE theory). For fatigue life or fatigue failure criteria, Replace Sut with Sgu. Ssu = 0.67Sµtarrow_forward5. This problem illustrate that the factor of safety for a machine element depends on the particular point selected for analysis. Compute factors of safety, based upon the distortion energy theory, for stress elements A and B of the member shown in the figure. This bar is made of AISI 1015 Cold-Drawn Steel and is loaded by the forces F= 500 N, P = 5000 N, and T=25 Nm. points) %3D %3D -100 mm 15-mm D.arrow_forward
- Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning