Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
10th Edition
ISBN: 9780073398204
Author: Richard G Budynas, Keith J Nisbett
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 6, Problem 29P
The figure is a drawing of a 4- by 20-mm latching spring. A preload is obtained during assembly by shimming under the bolts to obtain an estimated initial deflection of 2 mm. The latching operation itself requires an additional deflection of exactly 4 mm. The material is ground high-carbon steel, bent then hardened and tempered to a minimum hardness of 490 Bhn. The inner radius of the bend is 4 mm. Estimate the yield strength to be 90 percent of the ultimate strength.
- (a) Find the maximum and minimum latching forces.
- (b) Determine the fatigue factor of safety for infinite life, using the modified Goodman criterion.
Problem 6-29
Dimensions in millimeters
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A structural support for a machine is subjected to a static compression load of 20 kN.
The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel.
Specify suitable diameter for the cross section of the rod based on the basic size. Steel
data are available in Table A-10 from the textbook.
A-10 Typical propertics of carbon and alloy steels.
Ultimate strengih, s.
Yield strength,
Percent
Material SAE no.
Condition
ksi
MPa:
ksi
MP
clongation
Anncaled
Hot rolled
Cold drawn
57
65
75
393
448
517
43
48
64
296
331
441
36
36
20
1020
1020
1020
1040
Annealed
75
$17
352
30
Hot
1010
565
641
621
s52
16
Cold drawn
WQT 700
WQT 900
WQT 1100
WQT 1300
1040
876
814.
19
22
127.
1040
1040
1040
1040
107
87
600
63
434
32
1080
1080
1080
1080
Annealed
OQT 700.
OQT 900
OQT 100
OQT 1300
89
189
179
145
117
614
1303
1234
1000
807
54
141
129
372
972
889
P10
13
17
103
70
483
1080
352
655
T186
中6
14
Annealed
Cold drawn
OQT 700
OQT 900
OOT 1100
OQT 1300
87
112
193
146
116
94
600
772
1331
1007
800…
A 1000 mm cast iron pulley is fastened to a 112 mm shaft by means of a 28 mm squarekey 160 mm long. The key and shaft are SAE 1030 steel annealed with allowableshearing of key at 200 MPa and compressive of 660 MPa.
a. What force in lbs acting at the pulley rim will shear the key?b. What force in lbs acting at the pulley rim will crush the key?
A helical spring made of oil hardened and tempered steel
compression springs, made of circular wire, is subjected to
an axial force, which varies from (2.5 KN) to (3.5 KN). Over
this range of force, the deflection of the spring should be
approximately (5 mm). The spring index can be taken as (5).
The spring has square and ground ends. If ultimate tensile
strength of (1050 N/mm2) and modulus of rigidity of (81370
N/mm2). The permissible shear stress for the spring wire
should be taken as (50 %) of the ultimate tensile
strength.Design the spring and calculate the following: 1.
Wire diameter; 2. Mean coil diameter; 3. Number of active
coils; 4. Total number of coils; 5. Solid length of the spring; 6.
Free length of the spring: 7. pitch of coils (p); 8. Required
spring rate; 9. Actual spring rate; and 10. Draw a neat sketch
.of the spring showing various dimensions
Chapter 6 Solutions
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Ch. 6 - A 10-mm steel drill rod was heat-treated and...Ch. 6 - Prob. 2PCh. 6 - A steel rotating-beam test specimen has an...Ch. 6 - A steel rotating-beam test specimen has an...Ch. 6 - A steel rotating-beam test specimen has an...Ch. 6 - Repeat Prob. 6-5 with the specimen having an...Ch. 6 - A steel rotating-beam test specimen has an...Ch. 6 - Derive Eq. (6-17). Rearrange the equation to solve...Ch. 6 - For the interval 103 N 106 cycles, develop an...Ch. 6 - Estimate the endurance strength of a...
Ch. 6 - Two steels are being considered for manufacture of...Ch. 6 - A 1-in-diamctcr solid round bar has a groove...Ch. 6 - A solid square rod is cantilevered at one end. The...Ch. 6 - A rectangular bar is cut from an AISI 1020...Ch. 6 - A solid round bar with diameter of 2 in has a...Ch. 6 - The rotating shaft shown in the figure is machined...Ch. 6 - The shaft shown in the figure is machined from...Ch. 6 - Solve Prob. 6-17 except with forces F1 = 1200 lbf...Ch. 6 - Bearing reactions R1 and R2 are exerted on the...Ch. 6 - A bar of steel has the minimum properties Se = 40...Ch. 6 - Repeat Prob. 6-20 but with a steady torsional...Ch. 6 - Repeat Prob. 6-20 but with a steady torsional...Ch. 6 - Repeat Prob. 6-20 but with an alternating...Ch. 6 - A bar of steel has the minimum properties Se = 40...Ch. 6 - The cold-drawn AISI KUO steel bar shown in the...Ch. 6 - Repeat Prob. 6-25 for a load that fluctuates from...Ch. 6 - An M14 2 hex-head bolt with a nut is used to...Ch. 6 - The figure shows a formed round-wire cantilever...Ch. 6 - The figure is a drawing of a 4- by 20-mm latching...Ch. 6 - The figure shows the free-body diagram of a...Ch. 6 - Solve Prob. 6-30 except let w1 = 2.5 in. w2 = l.5...Ch. 6 - For the part in Prob. 630, recommend a fillet...Ch. 6 - Prob. 33PCh. 6 - Prob. 34PCh. 6 - A part is loaded with a combination of bending,...Ch. 6 - Repeat the requirements of Prob. 6-35 with the...Ch. 6 - 6-37 to 6-46For the problem specified in the build...Ch. 6 - 6-37 to 6-46For the problem specified in the build...Ch. 6 - 637 to 646 For the problem specified in the table,...Ch. 6 - For the problem specified in the table, build upon...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - Problem Number Original Problem, Page Number 637...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-47 to 6-50 For the problem specified in the...Ch. 6 - 6-47 to 6-50 For the problem specified in the...Ch. 6 - Prob. 49PCh. 6 - Prob. 50PCh. 6 - 6-51 to 6-53 For the problem specified in the...Ch. 6 - 6-51 to 6-53 For the problem specified in the...Ch. 6 - 6-51 to 6-53 For the problem specified in the...Ch. 6 - Solve Prob. 6-17 except include a steady torque of...Ch. 6 - Solve Prob. 618 except include a steady torque of...Ch. 6 - In the figure shown, shaft A, made of AISI 1020...Ch. 6 - A schematic of a clutch-testing machine is shown....Ch. 6 - For the clutch of Prob. 657, the external load P...Ch. 6 - A flat leaf spring has fluctuating stress of max =...Ch. 6 - A rotating-beam specimen with an endurance limit...Ch. 6 - A machine part will be cycled at 350 MPa for 5...Ch. 6 - The material properties of a machine part are Sut...Ch. 6 - Repeat Prob. 662 using the Goodman criterion....
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 1. Estimate the endurance strength of a 1.5-in-diameter rod of AISI 1040 steel having a machine finish and heat-treated to a tensile strength of 110kpsi, loaded in rotating bending.arrow_forwardCondition #1: A structural support for a machine is subjected to a static compression load of 20 kN. The manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the textbook. support is A-10 Typical properties of carbon and alloy stcels. Ultimate strength, s Yield strength, s, Percent Material SAE no. Condition ksi MPa ksi MPa elongation 1020 Annealed Hot rolled 57 393 43 296 36 1020 65 448 48 331 441 36 1020 Cold drawn 75 517 64 20 1040 Annealed Hot rolled Cold drawn 75 517 51 352 30 BO40 90 621 60 82 414 1040 97 669 565 16 1040 WQT 700 WQT 900 WQT 1100 WQT 1300 127 118 876 93 641 19 1040 814 90 621 1040 107 738 80 552 24 1040 87 600 63 434 32 1080 Annealed OQT 700 OQT 900 OQT 1100 OQT 1300 89 614 1303 1234 1080 54 372 25 189 179 145 117 141 129 972 889 710 1080 12 1O80 13 1000 103 70 17 23 1080 807 483 1141 Annealed 87 600 772 1141 51 352 26…arrow_forwardYour task is to design a full journal bearing to support the crankshaft of an engine. The crankshaft would be attached a journal that would be rotating within the bushing. The maximum speed of rotation of the crankshaft is 6000 rpm. The operating temperature is 130-F. The load on the bearing is 675lbf. The journal diameter has to fit on the crankshaft and has to be 2.5in. The length of the bearing has to be under 1.5in. The oil used in the engine is SAE 50. The performance of your bearing should have a maximum coefficient of friction of 0.04 and a minimum film thickness no lower than 0.001in. Determine the bearing dimensions you will use based on your goals and the charts in your formula sheet.arrow_forward
- 4. Determine the design stress for bolts in a cylinder cover where the load is fluctuating due to gas pressure. The maximum load on the bolt is 50 kN and the minimum is 30 kN. The load is unpredict- able and factor of safety is 3. The surface of the bolt is hot rolled and the suface finish factor is 0.9. During a simple tension test and rotating beam test on ductile materials (40 C 8 steel annealed), the following results were obtained : Diameter of specimen =12.5 mm; Yield strength= 240 MPa; Ultimate strength= 450 MPa; Endurance limit = 180 MPa. [Ans. 65.4 MPa]arrow_forwardA part is loaded with a combination of bending, axial, and torsion such that the following stresses are created at a particular location: Bending - Completely reversed, with a maximum stress of 60 MPa Axial - Constant stress of 20 MPa Torsion - Repeated load, varying from 0 MPa to 50 MPa Assume the varying stresses are in phase with each other. The part contains a notch such that Kibending = 1.4, Kaxial = 1.1, and K. = 2.0. The material properties are Sy = 300 MPa and S, = 400 MPa. The completely adjusted endurance limit is found to be Se= 200 MPa. Find the factor of safety for fatigue based on infinite life. If the life is not infinite, estimate the number of cycles. Be sure to check for yielding. f,torsionarrow_forwardA 37.5 mm round bar has been machined from AISI 1050 cold-drawn round bar Su =689 MPa. This part is to withstand a fluctuating tensile load varying from 0 to 72.5 kN. Because of the design of the ends and the fillet radius, a fatigue stress-concentration factor of 1.85 exists. Find the factor of safety F.S.arrow_forward
- Condition #1: A structural support for a machine is subjected to a static compression load of 20 kN. The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the textbook. Condition #2: The same structural support of the basic size determined in Condition 1 is subjected to a tensile load of 15 kN that is repeated several thousand times over the life of the machine. This load is not an addition to the 20 kN. Specify a suitable steel that is suitable to this application based on the basic size determined in Condition #1. Loading of Condition #1 does not apply here. Condition #3: The same structural support from Condition 2 is heated from room temperature of 25°C. The support is placed inside a frame on both ends. There is a total clearance of 0.2 mm between the support and its frame. Initial length of the rod is 200 mm. Specify the…arrow_forwardStarting with a spring index of C = 10, design a compression coil spring of 302 stainless wire with squared ends. The spring deflects 50 mm when a force of 90 N is applied and closes to solid when ys is 60 mm. At closure, use a design factor of 1.2 guarding against yielding. Select the smallest diameter wire where wire diameters are available in 0.2-mm increments between 0.2 and 3.2 mm. For the design, specify the wire diameter, the inside and outside diameters of the coil, the spring rate, the total number of coils, the free length of the spring, the final factor of safety, and stability conditions.arrow_forwardAn automobile engine has a valve spring is to be made of Fe, C, & Mn, to be oil-tempered, & to be designed that should not exceed to a cylindrical space of 134-in in diameter. The spring index should be 6.0, the coil-to-coil distance of 0.33in, & the maximum load it will sustain is 100lb with the corresponding compression of ½/2-in. The spring is subjected to repeated loading & fatigue must be considered by a factor of safety of 2.25. Determine: (a) the diameter of wire based on commercial sizes; (b) the total number of coils; (c) the free length of the spring. Sample image of valve spring in an assembly.arrow_forward
- Carbon Steel L=100mm dsmall= 20mm moment of inertia ratio between stepped cross-sectional area = 1:2 F=2500 N at A and a fillet radius at the step of 2mm -loading cycles that the design can withstand before fatigue failure - calculate cycles using goodman line and max stress from static analysis. -determine the effect of the 2mm fillet ratio on the fatigue analyisis. constant force at Aarrow_forwardScrew M14*2 Fasten with a hexagonal nut The bolt material meets the requirements within the 4.8 property class and the nut material belongs to the 5 property class Find the largest tensile strength of the bolt that can be tolerated without breakingarrow_forwardCalculate a diameter, d, to ensure that yield does not occur in the 1045 carbon steel (Yield stress = 310 MPa) under 220kN tensile load. Use a factor of safety of 5.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Relationship Between Elastic Constants and Connecting Equations; Author: Engineers Academy;https://www.youtube.com/watch?v=whW5PnM7Pug;License: Standard Youtube License