Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
10th Edition
ISBN: 9780073398204
Author: Richard G Budynas, Keith J Nisbett
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 6, Problem 26P
Repeat Prob. 6-25 for a load that fluctuates from 12 kN to 28 kN. Use the Modified Goodman. Gerber, and ASME-elliptic criteria and compare their predictions.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Ø20
R2
The 10-mm thick component in the figure is designed with a fillet and a hole. The load varies from
50 to 10 kN. The following strengths are given: S=390MPA and S,=282MPa. Using the Modified
Goodman Theory, determine the safety factor (assuming proportional loading) for the hole as
well as for the fillet. Select all non-given parameters (e.g., notch sensitivity factor, endurance
limit modifying factors, etc.) by your own – if you can justify your selections, that will be a bonus.
At which location will failure first occur? Will the component fail for infinite life expectation?
Explain in your own words.
If the component is determined to fail for infinite life expectation, lower the midrange and
amplitude of the force applied proportionally up to a level that infinite life can be expected. What
is the value of the force at this level?
3. The cold-drawn AISI 1040 steel plate shown in the figure below is subjected to a load that
fluctuates from 12 kN to 28 kN. Estimate the fatigue factor of safety on achieving infinite life
and the factor of safety guarding against first-cycle yielding.
For fatigue analysis, use:
1) Goodman; 2) Morrow.
6-mm D.
25 mm
10 mm
The round cross-sectional bar is cut from an AISI 1020 colddrawn steel with a diameter of 25 mm.
The bar is loaded at its end with a completely reversed load Fmin = 5 kN,
Fmax = -3 kN. Using a design factor of nd = 1.2, what will be the maximum
length of the bar that prevents failure using Modified Goodman criteria? What
length must be used if a more conservative criteria is used?
Chapter 6 Solutions
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Ch. 6 - A 10-mm steel drill rod was heat-treated and...Ch. 6 - Prob. 2PCh. 6 - A steel rotating-beam test specimen has an...Ch. 6 - A steel rotating-beam test specimen has an...Ch. 6 - A steel rotating-beam test specimen has an...Ch. 6 - Repeat Prob. 6-5 with the specimen having an...Ch. 6 - A steel rotating-beam test specimen has an...Ch. 6 - Derive Eq. (6-17). Rearrange the equation to solve...Ch. 6 - For the interval 103 N 106 cycles, develop an...Ch. 6 - Estimate the endurance strength of a...
Ch. 6 - Two steels are being considered for manufacture of...Ch. 6 - A 1-in-diamctcr solid round bar has a groove...Ch. 6 - A solid square rod is cantilevered at one end. The...Ch. 6 - A rectangular bar is cut from an AISI 1020...Ch. 6 - A solid round bar with diameter of 2 in has a...Ch. 6 - The rotating shaft shown in the figure is machined...Ch. 6 - The shaft shown in the figure is machined from...Ch. 6 - Solve Prob. 6-17 except with forces F1 = 1200 lbf...Ch. 6 - Bearing reactions R1 and R2 are exerted on the...Ch. 6 - A bar of steel has the minimum properties Se = 40...Ch. 6 - Repeat Prob. 6-20 but with a steady torsional...Ch. 6 - Repeat Prob. 6-20 but with a steady torsional...Ch. 6 - Repeat Prob. 6-20 but with an alternating...Ch. 6 - A bar of steel has the minimum properties Se = 40...Ch. 6 - The cold-drawn AISI KUO steel bar shown in the...Ch. 6 - Repeat Prob. 6-25 for a load that fluctuates from...Ch. 6 - An M14 2 hex-head bolt with a nut is used to...Ch. 6 - The figure shows a formed round-wire cantilever...Ch. 6 - The figure is a drawing of a 4- by 20-mm latching...Ch. 6 - The figure shows the free-body diagram of a...Ch. 6 - Solve Prob. 6-30 except let w1 = 2.5 in. w2 = l.5...Ch. 6 - For the part in Prob. 630, recommend a fillet...Ch. 6 - Prob. 33PCh. 6 - Prob. 34PCh. 6 - A part is loaded with a combination of bending,...Ch. 6 - Repeat the requirements of Prob. 6-35 with the...Ch. 6 - 6-37 to 6-46For the problem specified in the build...Ch. 6 - 6-37 to 6-46For the problem specified in the build...Ch. 6 - 637 to 646 For the problem specified in the table,...Ch. 6 - For the problem specified in the table, build upon...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - Problem Number Original Problem, Page Number 637...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-47 to 6-50 For the problem specified in the...Ch. 6 - 6-47 to 6-50 For the problem specified in the...Ch. 6 - Prob. 49PCh. 6 - Prob. 50PCh. 6 - 6-51 to 6-53 For the problem specified in the...Ch. 6 - 6-51 to 6-53 For the problem specified in the...Ch. 6 - 6-51 to 6-53 For the problem specified in the...Ch. 6 - Solve Prob. 6-17 except include a steady torque of...Ch. 6 - Solve Prob. 618 except include a steady torque of...Ch. 6 - In the figure shown, shaft A, made of AISI 1020...Ch. 6 - A schematic of a clutch-testing machine is shown....Ch. 6 - For the clutch of Prob. 657, the external load P...Ch. 6 - A flat leaf spring has fluctuating stress of max =...Ch. 6 - A rotating-beam specimen with an endurance limit...Ch. 6 - A machine part will be cycled at 350 MPa for 5...Ch. 6 - The material properties of a machine part are Sut...Ch. 6 - Repeat Prob. 662 using the Goodman criterion....
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Required information The cold-drawn AISI 1040 steel bar shown in the figure is subjected to an axial load that fluctuates from 8 kN to 30 kN. Use the Modified Goodman criterion and estimate the fatigue factor of safety based on achieving infinite life and the yielding factor of safety. 25 mm 10mm -6-mm D. What is the number of cycles to failure for this part? The number of cycles is 120000arrow_forwardThe figure below is subjected to a load fluctuating between Pmin and Pmax. Calculate the factor of safety n for unlimited life based on the Goodman criterion. Given D= 120 mm, d= 80 mm ,r= 16 mm, t=15 mm, Sut-700 MPa, and the reliability of 99.9%. The fillets and adjacent surfaces are ground. Pmin = 90i – 50 k (kN) and Pmax = 210i + 50 k (kN) P D Parrow_forwardYou are using a 10 mm thick and 25 mm wide, steel plate with a central hole of 5 mm subjected to a tension load as shown in the figure (1). The load fluctuates between 5 and 25 kN. Determine factor of safety against yielding and against fatigue using modified Goodman. Assuming reliability of 98%, and the plate is made of cold-drawn AISI 1050. d P Thickness, t Figure (1). Steel plate subjected to tension-tensionarrow_forward
- A solid square rod is cantilevered at one end. The rod is 0.6 m long and supports a completely reversing transverse load at the other end of ±2 kN. The material is AISI 1080 hot-rolled steel. If the rod must support this load for 10* cycles with a design factor of 1.5, what dimension should the square cross section have? Neglect any stress concentrations at the support end.arrow_forward2. The sketch shows a round bar with a groove loaded in bending. The material is annealed AISI 1040 steel, with an as-machined groove, and is to be designed with a reliability of 99%. (Note: This is a large shaft.) (a) What is the endurance limit of this specimen? Sz= k, cs kr kn Se (b) Estimate the safety factor using the Goodman line if the moment varies from-2000 Nm to +3630 Nm. ATSI 2 S - 3Sompaarrow_forwardCarbon Steel L=100mm dsmall= 20mm moment of inertia ratio between stepped cross-sectional area = 1:2 F=2500 N at A and a fillet radius at the step of 2mm -loading cycles that the design can withstand before fatigue failure - calculate cycles using goodman line and max stress from static analysis. -determine the effect of the 2mm fillet ratio on the fatigue analyisis. constant force at Aarrow_forward
- Two steels are being considered for the manufacture of as-forged connecting rods subjected to bending loads. One is AISI 4340 Cr-Mo-Ni steel capable of being heat- treated to a tensile strength of 260 kpsi. The other is a plain carbon steel AISI 1040 with an attainable Sut of 113 kpsi. Each rod is to have a size giving an equivalent diameter de of 0.24 in. Determine the endurance limit for each material. Is there any advantage of using the alloy steel for this fatigue application?arrow_forwardTwo steels are being considered for manufacture of as-forged connecting rods subjected to bending loads. One is AISI 4340 Cr-Mo-Ni steel capable of being heat-treated to a tensile strength of 260 ksi. The other is a plain carbon steel AISI 1040 with a ultimate strength of 113 ksi. Each rod is to have a size giving an equivalent diameter of 0.75 in. Determine the endurance limit for each material. Is there any advantage to using the alloy steel for this fatigue application?arrow_forwardA solid round bar with diameter of 2 in has a groove cut to a diameter of 1.8 in, with a radius of 0.1 in. The bar is not rotating. The bar is loaded with a repeated bending load that causes the bending moment at the groove to fluctuate between 0 and 25 000 lbf in. The bar is hot-rolled AISI 1095, but the groove has been machined. Determine the factor of safety for fatigue based on infinite life and the factor of safety for yielding. Plars & .arrow_forward
- This problem illustrates that the factor of safety for a machine element depends on the particular point selected for analysis. This bar is made of AISI 1006 cold-drawn steel and is loaded by the forces F=0.55 kN, P=4.0 kN, and T=25 N·m. (For AISI 1006 cold- drawn steel, S=280 MPa. “D." means diameter) (a) Calculate factor of safety at the position A based on the distortion-energy theory by calculating the von Mises stress. [6] (b) Calculate factor of safety at the position B based on the distortion-energy theory by calculating the von Mises stress. [6] unti O 15-mm D.arrow_forwardA bar is subjected to a combination of a steady load of 60kN and a load fluctuating between - 10kN and 90 kN. The corrected endurance limit of the bar is 150 MPa, the yield strength of the material is 480 MPa and the ultimate strength of the material is 600MPa. The bar cross-section is square with side a. If the factor of safety is 2, the value of a (in mm), according to the modified Goodman‟s criterion, is ____arrow_forwardA solid round bar with diameter of 2 in has a groove cut to a diameter of 1.8 in, with a radius of 0.1 in. The bar is not rotating. The bar is loaded with a repeated bending load that causes the bending moment at the groove to fluctuate between 0 and 25 000 lbf in. The bar is hot-rolled AISI 1095, but the groove has been machined. Determine the factor of safety for fatigue based on infinite life and the factor of safety for yielding. .arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
EVERYTHING on Axial Loading Normal Stress in 10 MINUTES - Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=jQ-fNqZWrNg;License: Standard YouTube License, CC-BY