Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
7th Edition
ISBN: 9780199339136
Author: Adel S. Sedra, Kenneth C. Smith
Publisher: Oxford University Press
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 4, Problem 4.51P
(a).
To determine
The small signal equivalent circuit and voltage gain for different values of DC bias current.
(b).
To determine
The largest voltage when signal current is limited to 10% of DC bias current.
The smallest value of I for which diode current remains within ±10% of DC bias current.
(c).
To determine
The largest possible output voltage for at most 10% deviation in DC bias current.
The value of corresponding peak input voltage and current in each diode.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
We know that the Si-diode will pass the current in a forward biased region. This behavior is useful for many applications.
Using Multisim build a circuit to observe the relation between the current and the voltage in Si-diode. (Use Diode 1N007GP, 5Ω resistor).
4. A voltage regulator circuit is shown on the right. The resistor
value is chosen to obtain an output voltage (across the diode)
of 0.7V.
Use the diode small-signal model to determine the change in
the output voltage when the supply voltage, V+, changes by
IV.
(This quantity is known as the line regulation and is generally
expressed in mV/V)
Hint: The answer will be only a function of V+
V+
▷
R
+
Vo
4. Design of an LED circuit
You must design a circuit for a light emitting diode. The circuit must be powered by a 3.3V power
source and you need a current of at least 2 mA current through the diode to ensure sufficient
brightness. At the same time you would also like to limit the diode current to no more than 5 mA
to limit your power consumption. Calculate a suitable value of the current limiting resistor for this
circuit if it is given that the LED will have a forward voltage drop of 2.1 V over it. Select a real
resistor value from the E12 standard resistor series. Show your reasoning and calculations.
Chapter 4 Solutions
Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
Ch. 4.1 - Prob. 4.1ECh. 4.1 - Prob. 4.2ECh. 4.1 - Prob. 4.3ECh. 4.1 - Prob. 4.4ECh. 4.1 - Prob. 4.5ECh. 4.2 - Prob. 4.6ECh. 4.2 - Prob. 4.7ECh. 4.2 - Prob. 4.8ECh. 4.2 - Prob. 4.9ECh. 4.3 - Prob. 4.10E
Ch. 4.3 - Prob. D4.11ECh. 4.3 - Prob. 4.12ECh. 4.3 - Prob. 4.13ECh. 4.3 - Prob. 4.14ECh. 4.3 - Prob. D4.15ECh. 4.4 - Prob. 4.16ECh. 4.4 - Prob. 4.17ECh. 4.4 - Prob. 4.18ECh. 4.5 - Prob. 4.19ECh. 4.5 - Prob. 4.20ECh. 4.5 - Prob. 4.21ECh. 4.5 - Prob. 4.22ECh. 4.5 - Prob. 4.23ECh. 4.5 - Prob. 4.24ECh. 4.5 - Prob. 4.25ECh. 4.6 - Prob. 4.26ECh. 4.6 - Prob. 4.27ECh. 4 - Prob. 4.1PCh. 4 - Prob. 4.2PCh. 4 - Prob. 4.3PCh. 4 - Prob. 4.4PCh. 4 - Prob. 4.5PCh. 4 - Prob. 4.6PCh. 4 - Prob. D4.7PCh. 4 - Prob. D4.8PCh. 4 - Prob. 4.9PCh. 4 - Prob. 4.10PCh. 4 - Prob. D4.11PCh. 4 - Prob. 4.12PCh. 4 - Prob. 4.13PCh. 4 - Prob. 4.14PCh. 4 - Prob. D4.15PCh. 4 - Prob. 4.16PCh. 4 - Prob. 4.17PCh. 4 - Prob. 4.18PCh. 4 - Prob. 4.19PCh. 4 - Prob. 4.20PCh. 4 - Prob. 4.21PCh. 4 - Prob. 4.22PCh. 4 - Prob. 4.23PCh. 4 - Prob. 4.24PCh. 4 - Prob. 4.25PCh. 4 - Prob. 4.26PCh. 4 - Prob. 4.27PCh. 4 - Prob. 4.28PCh. 4 - Prob. 4.29PCh. 4 - Prob. 4.30PCh. 4 - Prob. 4.31PCh. 4 - Prob. 4.32PCh. 4 - Prob. 4.33PCh. 4 - Prob. 4.34PCh. 4 - Prob. 4.35PCh. 4 - Prob. 4.36PCh. 4 - Prob. D4.37PCh. 4 - Prob. 4.38PCh. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - Prob. 4.41PCh. 4 - Prob. 4.42PCh. 4 - Prob. 4.43PCh. 4 - Prob. 4.44PCh. 4 - Prob. D4.45PCh. 4 - Prob. 4.46PCh. 4 - Prob. 4.47PCh. 4 - Prob. 4.48PCh. 4 - Prob. 4.49PCh. 4 - Prob. 4.50PCh. 4 - Prob. 4.51PCh. 4 - Prob. 4.52PCh. 4 - Prob. 4.53PCh. 4 - Prob. 4.54PCh. 4 - Prob. 4.55PCh. 4 - Prob. D4.56PCh. 4 - Prob. D4.57PCh. 4 - Prob. 4.58PCh. 4 - Prob. 4.59PCh. 4 - Prob. D4.60PCh. 4 - Prob. 4.61PCh. 4 - Prob. 4.62PCh. 4 - Prob. D4.63PCh. 4 - Prob. D4.64PCh. 4 - Prob. D4.65PCh. 4 - Prob. D4.66PCh. 4 - Prob. 4.67PCh. 4 - Prob. 4.68PCh. 4 - Prob. 4.69PCh. 4 - Prob. 4.70PCh. 4 - Prob. 4.71PCh. 4 - Prob. 4.72PCh. 4 - Prob. D4.73PCh. 4 - Prob. D4.74PCh. 4 - Prob. D4.75PCh. 4 - Prob. 4.76PCh. 4 - Prob. 4.77PCh. 4 - Prob. 4.78PCh. 4 - Prob. 4.79PCh. 4 - Prob. D4.80PCh. 4 - Prob. D4.81PCh. 4 - Prob. D4.82PCh. 4 - Prob. D4.83PCh. 4 - Prob. D4.84PCh. 4 - Prob. 4.85PCh. 4 - Prob. 4.86PCh. 4 - Prob. 4.87PCh. 4 - Prob. 4.88PCh. 4 - Prob. 4.89PCh. 4 - Prob. 4.90PCh. 4 - Prob. 4.91PCh. 4 - Prob. 4.92PCh. 4 - Prob. 4.93PCh. 4 - Prob. 4.94PCh. 4 - Prob. 4.95PCh. 4 - Prob. 4.96PCh. 4 - Prob. 4.97P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Given the circuit design for a Zener diode regulator in the previous question, what is the maximum power that will be dissipated by the Rs resistor? You are told that the source voltage Vs varies from 6 V to 11 V, the load current il varies between 2 mA and 45 mA, and the diode is an ideal 3 V Zener diode. You will need to recalculate the maximum allowable resistance Rs with your new values, as part of this question. Please enter your answer to 3 significant figures, and in Watts.arrow_forwardQ6. You need to connect three light emitting diodes (i) red, (ii) yellow and (iii) blue each to a 5V supply. Use the ideal diode plus voltage source model and for each of these LEDS calculate the resistor value that will produce a current of approximately 30 mA through the diode. Now select the actual resistor you will choose using the E12 resistor series and calculate the actual current through the LED in each case. It is given that the forward bias voltage drop over each of the LEDS are as follows: Vd = 1.5 V, Valow = 2.0 V and Volue = 3.5 V Diode Colour Red Yellow Resistor value Diode Current Bluearrow_forward10+ D NAME: The diodes in the circuit below have a saturation current Is = 10-¹4A. The NMOSFET has a threshold voltage of +1V and a K parameter of 10mA/V². > ID = Is (evo/VT - 1) a) Use the exponential diode model b) Oops. Someone built the circuit below, and apparently made a mistake selecting the components. They measure the voltage VA and it is equal to 1.9V. Based on VA = 1.9V, determine the expected value of V₂. +1 -3 V AVD -0.4 3-V 3-2V0 I VA=1.9V 041 VA to calculate VA. 2.2 ΚΩ +10V T 100 Ω NMOSFET VB Ins=4.05marrow_forward
- At what input voltage is necessary that can open the diode considering a voltage drop across the diode, VD=0.9V after the diode breakover? NO NEED TO COMPUTE FOR CURRENTarrow_forwardConsidering a clamper circuit, where capacitance C, load R, the built-in voltage of diode are unknown, which is the correct statement v The peak-to-peak value of signal changes The DC level shifts up The shape of signal changes The DC level of the signal changesarrow_forwardA silicon diode with a forward resistance of 10Ω is connected in series with a 500Ω resistor. If an A.Cvoltage of 20V peak is connected across the series combination of the diode and the resistor what willbe the peak value of the current through the diode and the peak output voltage? What will be the peakvalue of the current through the diode and the peak output voltage if the diode were ideal?arrow_forward
- SOLVE STEP BY STEP IN DIGITAL FORMAT For each of the circuits shown below, draw its voltage transfer curve, using the constant-drop model (all diodes are silicon identical, V_Don = 0.7V). Consider a variation of the input voltage from -10V to +10V. Vi V₁ D₁ D₁ Z D₂ 1k Circuit 1 1k Circuit 2 V₂ + V₂ Vi Vi 1k 1k D₁ Circuit 3 D₁ 1k ww 1k Circuit 4 + V₂ + V₂arrow_forwardA silicon diode is in parallel with a germanium diode and is connected to a load resistor having a value of 20 kQ and a forward supply voltage of 10 V. What is the approximate voltage across the silicon diode? * A. 10 V B. 1.0 V C. 0.7 V D. 0.3 Varrow_forward4) Design a circuit that will satisfy the input/output relation below using the following components: DC supply, 1k resistor and a) Ideal diode b) silicon diode Vi (V) Vo (V) 10- am 5 10 -5 -10 -5 -7.5arrow_forward
- The circuit below has a variable voltage vin as its input. We are interested in Vout as a function of Vin. In other words, if we vary the value of the voltage source vin, what will be the effect on the voltage Vout? The steps below will help you to investigate this question, and your answers will form the basis for a new design. Assume that the diode can be sufficiently modelled as simple diode with forward voltage of 0.7 V (you do not need Shockley's equation). Vin 100Ω M Vf = 0.7 V 2 V V outarrow_forwardWe have a junction diode that has iD = 0.2 mA for vD = 0.6 V. Assume that n = 2 and VT = 0.026 V. Use the Shockley equation to compute the diode current at vD = 0.65 V and at vD = 0.70 V.arrow_forwardWhat is the output voltage across a load resistor if it is paralleled with a forward biased silicon diode? The resistor network is supplied with 10 V. * O A. 0.7 V O B. 9.3 V O C. 10 V O D. Can't be solve, lack of data.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSON
Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
Programmable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill Education
Electric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSON
Engineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:PEARSON
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Programmable Logic Controllers
Electrical Engineering
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:9780078028229
Author:Charles K Alexander, Matthew Sadiku
Publisher:McGraw-Hill Education
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:9780134746968
Author:James W. Nilsson, Susan Riedel
Publisher:PEARSON
Engineering Electromagnetics
Electrical Engineering
ISBN:9780078028151
Author:Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:Mcgraw-hill Education,
19 Power Diodes | Power Electronics; Author: Walid Issa Plus;https://www.youtube.com/watch?v=_E-4bIYlNYQ;License: Standard Youtube License