Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
7th Edition
ISBN: 9780199339136
Author: Adel S. Sedra, Kenneth C. Smith
Publisher: Oxford University Press
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 4, Problem 4.32P
To determine
The range of the diode voltage.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
) State whether the following statements are true or false and then correct the false
ones.
i. In pn-junction diodes, the reverse saturation current stays constant
regardless of the ambient temperature.
i Under steady state, the overall charge of the depletion region in a diode
equals zero.
The peak inverse voltage of a pn-diode decreases with temperature.
The reverse recovery time of a diode determines the magnitude of the
forward diode current.
Design a voltage-regulator circuit to provide a constant voltage of 5 V to a load from a variable supply voltage. The load current varies from 0 to 100 mA, and the source voltage varies from 8 to 10 V. You may assume that ideal Zener diodes are available. Resistors of any value may be specified. Draw the circuit diagram of your regulator, and specify the value of each component. Also, find the worst case (maximum) power dissipated in each component in your regulator. Try to use good judgment in your design.
Design a voltage-regulator circuit to provide a constant voltage of 5 V to a load from a variable supply voltage. The load current varies from 0 to 100 mA, and the source voltage varies from 8 to 10 V. You may assume that ideal Zener diodes are available. Resistors of any value may be specified. Draw the circuit diagram of your regulator, and specify the value of each component. Also, find the worst case (maximum) power dissipated in each component in your regulator. Try to use good judgment in your design.
Repeat Problem P9.29 if the supply voltage ranges from 6 to 10 V.
Chapter 4 Solutions
Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
Ch. 4.1 - Prob. 4.1ECh. 4.1 - Prob. 4.2ECh. 4.1 - Prob. 4.3ECh. 4.1 - Prob. 4.4ECh. 4.1 - Prob. 4.5ECh. 4.2 - Prob. 4.6ECh. 4.2 - Prob. 4.7ECh. 4.2 - Prob. 4.8ECh. 4.2 - Prob. 4.9ECh. 4.3 - Prob. 4.10E
Ch. 4.3 - Prob. D4.11ECh. 4.3 - Prob. 4.12ECh. 4.3 - Prob. 4.13ECh. 4.3 - Prob. 4.14ECh. 4.3 - Prob. D4.15ECh. 4.4 - Prob. 4.16ECh. 4.4 - Prob. 4.17ECh. 4.4 - Prob. 4.18ECh. 4.5 - Prob. 4.19ECh. 4.5 - Prob. 4.20ECh. 4.5 - Prob. 4.21ECh. 4.5 - Prob. 4.22ECh. 4.5 - Prob. 4.23ECh. 4.5 - Prob. 4.24ECh. 4.5 - Prob. 4.25ECh. 4.6 - Prob. 4.26ECh. 4.6 - Prob. 4.27ECh. 4 - Prob. 4.1PCh. 4 - Prob. 4.2PCh. 4 - Prob. 4.3PCh. 4 - Prob. 4.4PCh. 4 - Prob. 4.5PCh. 4 - Prob. 4.6PCh. 4 - Prob. D4.7PCh. 4 - Prob. D4.8PCh. 4 - Prob. 4.9PCh. 4 - Prob. 4.10PCh. 4 - Prob. D4.11PCh. 4 - Prob. 4.12PCh. 4 - Prob. 4.13PCh. 4 - Prob. 4.14PCh. 4 - Prob. D4.15PCh. 4 - Prob. 4.16PCh. 4 - Prob. 4.17PCh. 4 - Prob. 4.18PCh. 4 - Prob. 4.19PCh. 4 - Prob. 4.20PCh. 4 - Prob. 4.21PCh. 4 - Prob. 4.22PCh. 4 - Prob. 4.23PCh. 4 - Prob. 4.24PCh. 4 - Prob. 4.25PCh. 4 - Prob. 4.26PCh. 4 - Prob. 4.27PCh. 4 - Prob. 4.28PCh. 4 - Prob. 4.29PCh. 4 - Prob. 4.30PCh. 4 - Prob. 4.31PCh. 4 - Prob. 4.32PCh. 4 - Prob. 4.33PCh. 4 - Prob. 4.34PCh. 4 - Prob. 4.35PCh. 4 - Prob. 4.36PCh. 4 - Prob. D4.37PCh. 4 - Prob. 4.38PCh. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - Prob. 4.41PCh. 4 - Prob. 4.42PCh. 4 - Prob. 4.43PCh. 4 - Prob. 4.44PCh. 4 - Prob. D4.45PCh. 4 - Prob. 4.46PCh. 4 - Prob. 4.47PCh. 4 - Prob. 4.48PCh. 4 - Prob. 4.49PCh. 4 - Prob. 4.50PCh. 4 - Prob. 4.51PCh. 4 - Prob. 4.52PCh. 4 - Prob. 4.53PCh. 4 - Prob. 4.54PCh. 4 - Prob. 4.55PCh. 4 - Prob. D4.56PCh. 4 - Prob. D4.57PCh. 4 - Prob. 4.58PCh. 4 - Prob. 4.59PCh. 4 - Prob. D4.60PCh. 4 - Prob. 4.61PCh. 4 - Prob. 4.62PCh. 4 - Prob. D4.63PCh. 4 - Prob. D4.64PCh. 4 - Prob. D4.65PCh. 4 - Prob. D4.66PCh. 4 - Prob. 4.67PCh. 4 - Prob. 4.68PCh. 4 - Prob. 4.69PCh. 4 - Prob. 4.70PCh. 4 - Prob. 4.71PCh. 4 - Prob. 4.72PCh. 4 - Prob. D4.73PCh. 4 - Prob. D4.74PCh. 4 - Prob. D4.75PCh. 4 - Prob. 4.76PCh. 4 - Prob. 4.77PCh. 4 - Prob. 4.78PCh. 4 - Prob. 4.79PCh. 4 - Prob. D4.80PCh. 4 - Prob. D4.81PCh. 4 - Prob. D4.82PCh. 4 - Prob. D4.83PCh. 4 - Prob. D4.84PCh. 4 - Prob. 4.85PCh. 4 - Prob. 4.86PCh. 4 - Prob. 4.87PCh. 4 - Prob. 4.88PCh. 4 - Prob. 4.89PCh. 4 - Prob. 4.90PCh. 4 - Prob. 4.91PCh. 4 - Prob. 4.92PCh. 4 - Prob. 4.93PCh. 4 - Prob. 4.94PCh. 4 - Prob. 4.95PCh. 4 - Prob. 4.96PCh. 4 - Prob. 4.97P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- a) Use the diode’s characteristic equation,ID=Is exp(VD/VT), to determine the currentsourceIso that the output voltage is 1.5 V. b) If a load is attached to the output that draws 1 mA, what is the output voltage? c) If the circuit heats up to 40◦C, what is the output voltage without a load?arrow_forwardFor the subsequent questions, please refer to the circuit below. Assume that the diode is ideal (e.g. the voltage across it is zero volts when it is ON) IK VIN=7V = J Syt + Jo Vo Suppose we assume the diode is ON, this is a wrong assumption because when we solve for lo with the diode as a short-circuit the condition ID>=0 will NOT hold as lp will be (in mA) ... Suppose we assume the diode is OFF, what is the resistor current I in mA? Suppose we assume the diode is OFF, what is Vo in volts? Suppose we assume the diode is OFF, our assumption is correct because the condition VD<=0 will hold as Vp will be (in volts) ...arrow_forwardDesign a Zener diode voltage regulator with a suitable circuit diagram and to consider the voltage regulator is used to power a cell phone at 4.5 V from a lithium ion battery pack, which voltage may vary between 5 V and 7.8 V. The current in the phone will vary 10 mA (when standby mode) to 150 mA (when talking). Assume that the Zener diode current, Iz(min) is 10% of Iz(max).arrow_forward
- As the forward current through a silicon diode increases, the voltage across the diode increases to a 0.7 V maximum. decreases and then increases. decreases. is relatively constant. A silicon diode in a half-wave rectifier has a barrier potential of 0.7 V. This has the effect of What is the order of doping, from heavily to lightly doped, for each region?arrow_forwardA half wave rectifier circuit with a 1K ohm load operates from a 120V rms 60-Hz household supply through a 10-to-1 step down transformer. It uses a silicon diode that can be modeled to have a 0.7V drop for any current. What is the peak voltage of the rectified output? For what fraction of a cycle does the diode conduct? What is the average output voltage? What is the average current in the load? Thanks for any help.arrow_forwardConsidering a clamper circuit, where capacitance C, load R, the built-in voltage of diode are unknown, which is the correct statement? The DC level shifts up The DC level of the signal changes The shape of signal changes The peak-to-peak value of signal changesarrow_forward
- 24 A 30-volt forward voltage is applied to a silicon diode in series with a load of 3 kf2. Draw the de load line. What is the slope of the line? Solution The value of voltage Vy across diode is given by V, V R, Since R and V are fixed values, this equation can by represented by a straight line on V- characteristics of diode; this is de load line. When Ip 0, maximum voltage across the diode V 30 V. This is point B(30, 0). 10 mA 30 V Fig. 2.25 Problem 2.4.arrow_forwardUsing one NPN transistor, one PNP transistor, one general purpose diode, one LED and two resistors, design a constant current source that drives a constant current of 20 mA through the LED. The circuit is supplied with 10V from an ideal voltage source. The general purpose diode cannot handle more than 10 mA. You MUST use all six components given. ( Calculate the resistance of the two resistors. The transistors and the diode use Silicon (VT = 0.7V). Both transistors have B = 500.arrow_forwardGiven the clamper circuit below, assume that the value of R and C are large enough sothe voltage across the capacitor does not change significantly during the interval of time.a. Using the simplified diode model, simulate the action of the circuit when the Silicon diode isin forward and reverse bias condition and measure the corresponding output voltage.b. Draw the complete output waveform of the circuitarrow_forward
- You are asked to design a Zener diode voltage regulator, as shown in Figure 1.e, tỏ have a stabilized voltage of 3.3 V across the load R,. The Zener diode has a constant voltage of 3.3 V when its current is more than a minimum current of 10 mA and has negligible dynamic resistance. The load current changes between 0 mA (open circuit) and 200 mA. The input voltage Vị is equal to 5 V. Choose the value of series resistance Rs to have stabilized voltage at the output at all conditions. ii) Calculate the maximum current in the diode and the resistor Re. Based on these values, choose the maximum power ratings of the diode and the resistor Rs RL Rsarrow_forwardFor the circuit shown below, both diodes are identical with and the input voltage is . To analyze the circuit, we assume that both diodes are conducting (on). Is this correct? If yes, what is the value of ID1? If no, what are the correct diode states?arrow_forwardCurrent measured in the circuit in the shape created using the ideal diode model .....is. Please select one: a. 0.87 mA b. 1.2 mA c. 0.80 mA d. 0.73 mAarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSON
Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
Programmable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill Education
Electric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSON
Engineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:PEARSON
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Programmable Logic Controllers
Electrical Engineering
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:9780078028229
Author:Charles K Alexander, Matthew Sadiku
Publisher:McGraw-Hill Education
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:9780134746968
Author:James W. Nilsson, Susan Riedel
Publisher:PEARSON
Engineering Electromagnetics
Electrical Engineering
ISBN:9780078028151
Author:Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:Mcgraw-hill Education,
Demos: Dielectric breakdown; Author: Caltech's Feynman Lecture Hall;https://www.youtube.com/watch?v=2YrHh1ikefI;License: Standard Youtube License