Scissors are like a double-lever "Stem, Which of the Simple machines in Figure 9.23 and Figure 9.24 is most analogous to scissors?
Figure 9.23 A nail puller is a lever with a large mechanical advantage. The external forces on the nail puller are represented by solid arrows. The force that the nail puller applies to the nail ( Fo ) is not a force on the nail puller. The reaction force the nail exerts back on the puller ( Fn ) is an external force and is equal and opposite to Fo. The perpendicular lever arms of the input and output forces are li and l0
Figure 9.24 (a) In the case of the wheelbarrow, the output force or load is between the pivot and the input force. The pivot IS the wheel's axle. Here, the output force is greater than the input force. Thus, a wheelbarrow enables you to lift much heavier loads than you could with your body alone. (b) In the case of the shovel, the input force is between the pivot and the load, but the input lever arm is shorter than the output lever arm. The pivot is at the handle held by the right hand. Here, the output force (supporting the shovel's load) is less than the input force (from the hand nearest the load), because the Input is exerted closer to the pivot than is the output
Trending nowThis is a popular solution!
Chapter 9 Solutions
College Physics
Additional Science Textbook Solutions
Sears And Zemansky's University Physics With Modern Physics
Physics: Principles with Applications
University Physics Volume 2
College Physics: A Strategic Approach (4th Edition)
Tutorials in Introductory Physics
- The steel wrecking “ball” is suspended from the boom using an old rubber tire A. The crane operator lifts the ball then allows it to drop freely to break up the concrete. Explain, using appropriate numerical data, why it is a good idea to use the rubber tire for this work.arrow_forwardFigure 4 100 g 7. Place a clamp with a hanging mass of 300 g at the 30.0 cm mark of the half-meter stick (Figure 5). Place the second clamp at the 5.0 cm mark on the fulcrum and the third clampa the 40.0 cm mark with a hook upward. Hang the upward hook to a spring balance and find the reading on the balance. Be sure to keep the half-meter stick horizontal 2.66N 10 20 50 luuluuluulw 300g Figure 5 8. Interchange the spring balance with the fulcrum and read the spring balance. 162Narrow_forwardRepeat Exercise 9.24 for the pulley shown in Figure 9.26(c), assuming you pull straight up on the rope. The pulley system's mass is 7.00 kg.arrow_forward
- Using a screwdriver, you try to remove a screw from a piece of furniture, but cant get it to turn. To increase the chances of success, you should use a screwdriver that (a) is longer, (b) is shorter, (c) has a narrower handle, or (d) has a wider handle.arrow_forwardTwo women lift an elephant 777kg weight with a crowbar when the fulcrum for this lever is 0.18m from the weight and the women exerts their strengths at 0.69m and 6.9m respectively from the fulcrum. If the women interchange positions, they can raise a 999 kg elephant. How much force does each women exert?arrow_forwardThe father and son is seated on a 5-meter long seesaw. If the 30-kg son is seated at one end, the 50-kg father must be seated at Blank 1 meter from the other end. Blank 1 Add your answerarrow_forward
- anwser all 3 parts please! all 3 parts are the same one problemarrow_forwardE Boview Find the force that the floor exerts on each of his feet, assuming that both feet exert the same force. To strengthen his arm and chest muscles, a 79-kg athlete 2.0 m tall is doing a series of push-ups as shown in the figure below (Figure 1). His center of mass is 1.20 m from the bottom of his feet, and the centers of his palms are 30.0 cm from the top of his head. Express your answerkn newtons. F- 125.24 Submit Previou Answers Reguest Answer X Incorrect; Try Again; 4 attempts remaining Part B Figure 1 of 1> Find the force that the floor exerts on each of his hands, assuming both palms exert the same force. Express your answer in newtons. -20m F- 114 -300 on Submit Previous Answers Bequest Answer X Incorrect; Try Again; 5 attempts remaining P Pearsonarrow_forwardQ10a The 9.75 m long beam is simply supported at A and B as shown below with a uniformly distributed load (UDL) between A and C of 4.75 kN/m and a concentrated point load of 12.50 kN at point D (i.e., midpoint between C & B). Determine the reaction force RA acting at A in kilonewtons (kN). Assume the beam is weightless and give your answer in kilonewtons (kN) to 2 decimal places. 12.50 kN 4.75 kN/m 1.125 m A 7.50 m 2.25 m C B Answer:arrow_forward
- One person was doing a knee extensor muscle training, he used a dumbbell (mass = 10.2 kg) strapped to the ankle joint and was 0.4 m from the knee joint (see attached figure). The dumbbell was 0.3 m away from the knee joint in the horizontal direction. If the lever arm for the knee extensor muscle force was 0.04 m about the knee joint center, what amount of force must the knee extensor muscle produce to hold the leg in the above position? (Ignore the weight of the leg) Group of answer choicesarrow_forwardOne person was doing a knee extensor muscle training, he used a dumbbell (mass = 10.2 kg) strapped to the ankle joint and was 0.4 m from the knee joint (see attached figure). The dumbbell was 0.3 m away from the knee joint in the horizontal direction. if the lever arm for the knee extensor muscle force was 0.04 m about the knee joint center, what amount of force must the knee extensor muscle produce to hold the leg in the above position? (Ignore the weight of the leg)arrow_forwardYou are to design a pick-and-place robot using an RRPR 4 DOF SCARA (Selective Compliance Assembly Robot Arm) robot shown in the figure below. Take L1 = 0.5 m, L2 = 0.4 m, L3 = 0.1 m, and L4 = 0.3 m. 1.Redraw the robot in a clean and tidy way, then assign the frames to the joints using the DH convention. You MUST follow the depicted orientation and direction of the joints. 2.Using the D-H method, construct the Joint/Link Parameter Table.arrow_forward
- College PhysicsPhysicsISBN:9781938168000Author:Paul Peter Urone, Roger HinrichsPublisher:OpenStax CollegeCollege PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning