Concept explainers
A 17.0-m-high and 11.0-m-long wall under construction and its bracing are shown in Figure 9.32. The wall is in stable equilibrium without the bracing but can pivot at its base. Calculate the force exerted by each of the 10 braces if a strong wind exerts a horizontal force of 650 N on each square meter of the wall. Assume that the net force from the wind acts at a height halfway up the wall and that all braces exert equal forces parallel to their lengths. Neglect the thickness of the wall.
Trending nowThis is a popular solution!
Chapter 9 Solutions
College Physics
Additional Science Textbook Solutions
Sears And Zemansky's University Physics With Modern Physics
College Physics (10th Edition)
University Physics with Modern Physics (14th Edition)
Conceptual Physics (12th Edition)
Physics for Scientists and Engineers: A Strategic Approach with Modern Physics (4th Edition)
Lecture- Tutorials for Introductory Astronomy
- Modelled after problem 5 in the Problems_Torque_Statics: A 16.19-m-high and 11.44-m-long wall under construction and its bracing are shown in the figure. The wall is in stable equilibrium without the bracing but can pivot at its base. Calculate the force exerted by each of the 10 braces if a strong wind exerts a horizontal force of 673.77 N on each square meter of the wall. Assume that the net force from the wind acts at a height halfway up the wall and that all braces exert equal forces parallel to their lengths. Neglect the thickness of the wall. The angle between the braces and the wall is as shown in the figure as 35 degrees. answer is 21,756.7113 but how?arrow_forwardA 17.0 m-high and 12.0 m-long wall under construction and Its bracing are shown in the figure below. The wall is In stable equllibrium without the bracing but can plvot at its base. Calculate the force (In N) exerted by each of the 10 braces if a strong wind exerts a horizontal force of 715 N on each square meter of the wall. Assume that the net force from the wind acts at a helght halfway up the wall and that all braces exert equal forces parallel to their lengths. Neglect the thickness of the wall. (Enter the magnitude.) Fwind 17.0m 8.5 m 135 10 braces 2.54 X Narrow_forward130.acellus.com/Student Functions/Interface/acellus_engine.html?ClassID=28... ✔ A vaulter is holding a horizontal 3.00-kg pole, 4.50 m long. His front arm lifts straight up on the pole, 0.750 m from the end, and his back arm pushes straight down on the end of the pole. How much force does his back arm exert on the pole? Fback = [?] N onal Academy of Science. All Rights Reserved. Q Search H Enter huluarrow_forward
- Consider the trusses shown in the figure below. The vertical reaction in the hinged support is Blank 1 N. 2 m 200 N 1 m C 2m 200 N E D 2 marrow_forwardAs seen in the figure, a 700N bear is trying to get the food at the end of the plank. The food basket is 80N in weight, the plank is 200N in weight and 6m long. Draw the force diagram for the plank. Since the wire connecting the plank to the ceiling can withstand a maximum 900N stress, how far can the bear go from the wall?arrow_forwardA meter stick is balanced at its center. If a 3 kg mass is suspended at x=0 m, where would you need to place a mass of 5 kg to have the system in equilibrium? Note: The meter stick goes from 0 m to 1 m; therefore its center is at the 0.5 m mark. (It is based on this lab https://phet.colorado.edu/sims/html/balancing-act/latest/balancing-act_en.html)arrow_forward
- A uniform, 8.00 m, 1150kg beam is hinged to a wall and supported by a thin cable attached to a 2.00 m from the free end of the beam as shown. Find the tension in the thin cable. Do not forget the force of gravity on the beam. b) How hard does the beam push inward on the wall? what is the horizontal force on the beam from the wall?arrow_forward1 b F2 1 1 FR F1 b. The figure above shows a crane tower on site at the HWY 1 expansion and Stoney Trail extension in NW Calgary. You are a design engineer working for the company supplying cranes for the contractors and you have been asked to evaluate the tower design. The crane tower supporting the pulley is designed so that the resultant force from the cable tension running over the pulley is oriented along the tower axis. Note: The tension in the cable is the same on both sides so ||Fill = ||F2l|| = T.arrow_forwardA uniform 1450 kg beam that is 18 m long is balanced on two vertical support beams at either end of the beam (see figure 9-8). A crate which weighs 520 kg is positioned 4.0 m from the first support beam. Calculate the force on each of the vertical support beams.arrow_forward
- The 310-kg uniform I-beam supports the load shown. Determine the reactions at the supports. Answers: Ax= Ay = By= Mi i i -8.5 m- 3.5 m 250 kg N N N Barrow_forwardA 10m beam of mass of 300 kg extends over a ledge. The beam is not held down but simply rest on the surface. A 60 kg student has positioned the beam so that he can walk to the end of it. How far far the edge of the ledge can the beam extend?arrow_forwardThe 585-kg uniform I-beam supports the load shown. Determine the reactions at the supports. -6.1 m Answers: Ax= B,= i i +1.9 m 290 kg N N Narrow_forward
- College PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningUniversity Physics (14th Edition)PhysicsISBN:9780133969290Author:Hugh D. Young, Roger A. FreedmanPublisher:PEARSONIntroduction To Quantum MechanicsPhysicsISBN:9781107189638Author:Griffiths, David J., Schroeter, Darrell F.Publisher:Cambridge University Press
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningLecture- Tutorials for Introductory AstronomyPhysicsISBN:9780321820464Author:Edward E. Prather, Tim P. Slater, Jeff P. Adams, Gina BrissendenPublisher:Addison-WesleyCollege Physics: A Strategic Approach (4th Editio...PhysicsISBN:9780134609034Author:Randall D. Knight (Professor Emeritus), Brian Jones, Stuart FieldPublisher:PEARSON