Foundations of Materials Science and Engineering
6th Edition
ISBN: 9781259696558
Author: SMITH
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Question
Chapter 7.10, Problem 46SEP
(a)
To determine
The safe operating pressure if there is no preexisting cracks. Vessel are made of titanium alloy
(b)
To determine
The safe operating pressure if there is crack of length
(c)
To determine
The safe operating pressure if crack length is
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Experience in non-destructive testing of 7075-T651 aluminum (Sy = 72 ksi, KIC = 22 ksi in1/2) pressurized pipes dictates that the minimum detectable longitudinal crack length is 10 mm. Thus, a longitudinal crack of length 10 mm could escape detection and be present at any time. The pipes transmit a flow of natural gas and the presence of a crack would not alter the internal pressure. What maximum internal pressure would you recommend? Neglect the pipe curvaturewhen determining the stress intensity factor.
Help me please
Problem 4. A large flat plate is subjected to constant-amplitude uniaxial cyclic tensile and compressive stresses. Compute the final critical surface crack length if the fatigue life must be a minimum of 7.0 x 10^5 cycles. Assume the initial maximum edge surface crack length of 1.80 mm and a maximum tensile stress of 160 MPa. Assume m = 1.8 and A = 7.5 x 10^-13 in MPa and meter units. Assume Y = 1.25.
Chapter 7 Solutions
Foundations of Materials Science and Engineering
Ch. 7.10 - What are the characteristics of the surface of a...Ch. 7.10 - Prob. 2KCPCh. 7.10 - Prob. 3KCPCh. 7.10 - Prob. 4KCPCh. 7.10 - Prob. 5KCPCh. 7.10 - Prob. 6KCPCh. 7.10 - Prob. 7KCPCh. 7.10 - Prob. 8KCPCh. 7.10 - Prob. 9KCPCh. 7.10 - How does the carbon content of a plain-carbon...
Ch. 7.10 - Describe a metal fatigue failure.Ch. 7.10 - What two distinct types of surface areas are...Ch. 7.10 - Prob. 13KCPCh. 7.10 - Prob. 14KCPCh. 7.10 - Prob. 15KCPCh. 7.10 - Describe the four basic structural changes that...Ch. 7.10 - Describe the four major factors that affect the...Ch. 7.10 - Prob. 18KCPCh. 7.10 - Prob. 19KCPCh. 7.10 - Prob. 20KCPCh. 7.10 - Prob. 21KCPCh. 7.10 - Determine the critical crack length for a through...Ch. 7.10 - Determine the critical crack length for a through...Ch. 7.10 - The critical stress intensity (KIC) for a material...Ch. 7.10 - What is the largest size (in mm) of internal...Ch. 7.10 - A Ti-6Al-4V alloy plate contains an internal...Ch. 7.10 - Using the equation KIC=fa, plot the fracture...Ch. 7.10 - (a) Determine the critical crack length (mm) for a...Ch. 7.10 - A fatigue test is made with a maximum stress of 25...Ch. 7.10 - A fatigue test is made with a mean stress of...Ch. 7.10 - A large, flat plate is subjected to...Ch. 7.10 - Prob. 32AAPCh. 7.10 - Refer to Problem 7.31: Compute the final critical...Ch. 7.10 - Prob. 34AAPCh. 7.10 - Prob. 35AAPCh. 7.10 - Equiaxed MAR-M 247 alloy (Fig. 7.31) is used to...Ch. 7.10 - Prob. 37AAPCh. 7.10 - If DS CM 247 LC alloy (middle graph of Fig. 7.31)...Ch. 7.10 - Prob. 39AAPCh. 7.10 - Prob. 40AAPCh. 7.10 - Prob. 41SEPCh. 7.10 - Prob. 42SEPCh. 7.10 - A Charpy V-notch specimen is tested by the...Ch. 7.10 - Prob. 44SEPCh. 7.10 - Prob. 45SEPCh. 7.10 - Prob. 46SEPCh. 7.10 - Prob. 47SEPCh. 7.10 - Prob. 48SEPCh. 7.10 - Prob. 49SEPCh. 7.10 - Prob. 50SEPCh. 7.10 - While driving your car, a small pebble hits your...Ch. 7.10 - Prob. 52SEPCh. 7.10 - Prob. 53SEPCh. 7.10 - Prob. 54SEPCh. 7.10 - Prob. 56SEPCh. 7.10 - Prob. 57SEPCh. 7.10 - Prob. 58SEPCh. 7.10 - Prob. 59SEPCh. 7.10 - The components in Figure P7.60 are high-strength...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What is the magnitude of the maximum stress that exists at the tip of an internal crack having a radius of curvature of 1.9 x 10" mm and a crack length of 3.8 x 10 mm when a tensile stress of 140 MPa is applied? 4. 5. A ceramic matrix composite contains internal flaws as large as 0.001 cm in length. The plane strain fracture toughness of the composite is 45 and the tensile strength is 550 MPa. Will the flaw cause the composite to fail before the tensile strength is reached? Assume that Y 1 A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is to be subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 1.3 mm. when the applied load is 29,000 N, which of the four met ls or alloys listed below are possible cardidates? Justify your choice(s). Materia! Modulus of Yield Tensiie Strength (MPa) Elasticity(GPa) Strength(MPa) Aluminium alloy 70 255 420 Brass alloy 100 345 420 Сopper 110 210arrow_forwardAn Al2O3 part contains both internal cracks with a maximum length of 0.075 mm, and external cracks with a maximum length of 0.05 mm. At what applied stress will the internal cracks begin to propagate? At what applied stress will the external cracks begin to propagate? The fracture toughness KIC = 1.76 MPa x m1/2, Y=1.arrow_forwardAccording to Griffith's theory for brittle fracture, the stress required to propagate a crack is: (This question has more than one correct answer) 0.5 a. Proportional to a' where 2a is the crack length b. More than the ideal fracture stress -0.5 c. Proportional to a d. Less than the ideal fracture stress e. Proportional to the surface energy y0.5 f. Proportional to the surface energy yarrow_forward
- QUESTION 8 A small component is made from aluminium 7475 where Kc = 35.2 MPa m 1/2 Non-destructive testing by micro-computed tomography showed the component to contain cracks of up to 2a = 0.05 mm in length. Laboratory tests showed the crack growth rate under cyclic loading is given by: Where A= 1.10x10-13 Assuming that: da dN = ΑΔΚΑ (MN m-2)-4 m-1 and the component is subjected to an alternating stress of range A = 180 MPa about a mean tensile stress of 40/2. ΔΚ = Δονπα Calculate the number of cycles to failure, give your answer in number of 1000s of cycles to 3 significant figures (e.g. 101,000 cycles would be inputted as 101)arrow_forwardWhat is the magnitude of the maximum stress that exists at the tip of an internal crack having a radius of curvature of 2.5 × 10-4 mm (0.9843 × 10-5 in.) and a crack length of 3 × 102 mm (1.181 × 10-3 in.) when a tensile stress of 140 MPa (20310 psi) is applied?arrow_forwardTutorial 4 A 70 mm diameter bar is found to contain a a crack which is located circumferentially 8mm deep around the outer surface, and penetrating 8 mm deep. The bar is subjected to cyclic stress which varies from 40 MN/m? to 100 70 mm dia. MN/m?. Given that Kic=60 MN/m3/2 for the same environment, determine whether the crack will propagate to the failure.arrow_forward
- What is the magnitude of the maximum stress that exists at the tip of an internal crack having a radius of curvature of 2.5 × 104 mm (10- in.) and a crack length of 2.5 × 10-2 (10-3 in.) when a tensile stress of 170 MPa (25,000 psi) is applied? mmarrow_forwardA very wide plate with a 2" long center crack is heated in order to be brazed to its end supports. The plate is made of a material with Elastic modulus of 15x10$psi and a = 6x10-º in/in/°F. Considering the brazed ends become rigid supports at 400°F and assuming that the material has a constant Fracture Toughness of 30ksivlin, at what temperature will the plate fracture? [hint: use B (geometric factor) =1.0 for this geometry]arrow_forwardA fuel transportation industry uses a spherical 1045 carbon steel pressure vessel with a diameter of 800 mm and a thickness of 30 mm, covered with a brittle varnish that cracks in the vessel cover when the deformation exceeds 200 x 106. What is the value of the internal pressure that causes the varnish to develop cracks? (Assume E = 205 GPa and v = 0.30). Explain you answer.arrow_forward
- A test specimen data made of polyvinyl chloride with 10.16-mm-diameter were collected (l. = 50.80 mm) and shown in Table 1. After fracture, the total length was extended to 53.08 mm and the diameter was 9.98 mm. Load (kN) Al (mm) 0 0.00 1.35 0.19 2.65 0.40 4.00 0.60 5.35 0.81 6.65 1.17 7.35 1.78 (maximum load) 7.10 2.39 6.30 3.05 (fracture) Table 1: The results of the tensile test for polyvinyl chloride. Plot the engineering stress-strain curve (list the stress and strain value in a Table) and evaluate: (i) (ii) the 0.2% offset yield strength; the modulus of elasticity; (iii) the percentage of reduction in area; (iv) the engineering stress at fracture; (v) the modulus of resilience.arrow_forwardSome aluminum aircraft components have a KIc = 35 MPa(m)1/2. It has been determined that failure occurs at a stress of 250 MPa when the critical internal crack length is 2 mm. Will this component achieve failure at a stress of 325 MPa when the critical internal crack length is 1.1 mm?arrow_forwardla. In the design of a pressure vessel, the leak-before-break criterion is used considering the circumferential wall thickness and the plain strain fracture toughness. The design is limited by the yield strength gs and the factor of safety (SF). Derive expressions for the critical crack size. 1b. Calculate the design stress and stress intensity factor if the safety factor is 1.5. Data: gxS = 586 MPa and KIC = 33 MPa m1/2.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Understanding Failure Theories (Tresca, von Mises etc...); Author: The Efficient Engineer;https://www.youtube.com/watch?v=xkbQnBAOFEg;License: Standard youtube license