Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 7, Problem 38P
The thrust of a marine propeller is to be measured during “open-water” tests at a variety of angular speeds and forward speeds (“speeds of advance”). The thrust, FT, is thought to depend on water density, ρ, propeller diameter, D, speed of advance, V, acceleration of gravity, g, angular speed, ω, pressure in the liquid, p, and liquid viscosity, μ. Develop a set of dimensionless parameters to characterize the performance of the propeller. (One of the resulting parameters, gD/V2, is known as the Froude speed of advance.)
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
At a sudden contraction in a pipe the diameter changes from D, to D2. The pressure drop, Ap, which develops across the con- traction is a function of D, and Dz, as well as the velocity, V, in the larger pipe, and the fluid density, p, and viscosity, u. Use D, V, and u as repeating variables to determine a suitable set of dimensionless parameters. Why would ti be incorrect to include the velocity in the smaller pipe a sa nadditional variable?
The conduction heat transfer in an extended surface, known as a fin, yields
the following equation for the temperature T, if the temperature distribution
is assumed to be one-dimensional in x, where x is the distance from the
base of the fin, as shown in figure:
To
Fin
>X
T(x)
h,T
Heat Loss
d²T_hp (T-T) = 0
dx² ΚΑ
dT
dx
= 0
Here, p is the perimeter of the fin, being 2R for a cylindrical fin of radius
R; A is the cross-sectional area, being R2 for a cylindrical fin; k is the
At x = 0: T = T₁
dT
At x=L:
:0
dx
thermal conductivity of the material; T is the ambient fluid temperature;
and h in the convective heat transfer coefficient. The boundary conditions
are as follows:
where L is the length of the fin. Solve this equation to obtain 7(x) by using
Euler's method for R=1cm, h= 20 W/m².K, k = 15 W/m-K, L = 25 cm,
T₁ = 80°C, and T = 20°C.
The pressure difference ∆p produced by a water pump, and the power P required to operate it, each depend on the size of the pump, measured by the diameter D of the impeller, the volume flow rate ˙q, the rate of rotation ω, the water density ρ and dynamic viscosity µ. (a) Express the non-dimensional pressure difference and power as separate functions of the other non-dimensional groups. (b) Tests on a model pump are performed at 0.5 × full scale, at a rotation rate that is 2 × the full-scale value. To achieve dynamic similarity in the model test: (i) what would the volume flow rate of the water need to be in the model test compared to the full-scale? (ii) What would the pressure difference be compared to the full scale? (iii) What would the power consumption be relative to the full scale?
Chapter 7 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 7 - The slope of the free surface of a steady wave in...Ch. 7 - One-dimensional unsteady flow in a thin liquid...Ch. 7 - In atmospheric studies the motion of the earths...Ch. 7 - Fluid fills the space between two parallel plates....Ch. 7 - By using order of magnitude analysis, the...Ch. 7 - Consider a disk of radius R rotating in an...Ch. 7 - An unsteady, two-dimensional, compressible,...Ch. 7 - Experiments show that the pressure drop for flow...Ch. 7 - At very low speeds, the drag on an object is...Ch. 7 - We saw in Chapter 3 that the buoyant force, FB, on...
Ch. 7 - Assume that the velocity acquired by a body...Ch. 7 - Derive by dimensional analysis an expression for...Ch. 7 - The speed of shallow water waves in the ocean...Ch. 7 - The speed, V, of a free-surface wave in shallow...Ch. 7 - The boundary-layer thickness, , on a smooth flat...Ch. 7 - The speed, V, of a free-surface gravity wave in...Ch. 7 - Derive an expression for the velocity of very...Ch. 7 - Derive an expression for the axial thrust exerted...Ch. 7 - Derive an expression for drag force on a smooth...Ch. 7 - The energy released during an explosion, E, is a...Ch. 7 - Measurements of the liquid height upstream from an...Ch. 7 - The load-carrying capacity, W, of a journal...Ch. 7 - Derive an expression for the drag force on a...Ch. 7 - A circular disk of diameter d and of negligible...Ch. 7 - Two cylinders are concentric, the outer one fixed...Ch. 7 - The time, t, for oil to drain out of a viscosity...Ch. 7 - You are asked to find a set of dimensionless...Ch. 7 - A continuous belt moving vertically through a bath...Ch. 7 - Derive an expression for the frictional torque...Ch. 7 - Tests on the established flow of six different...Ch. 7 - The power, P, required to drive a fan is believed...Ch. 7 - The sketch shows an air jet discharging...Ch. 7 - The diameter, d, of bubbles produced by a...Ch. 7 - Choked-flow nozzles are often used to meter the...Ch. 7 - A large tank of liquid under pressure is drained...Ch. 7 - Spin plays an important role in the flight...Ch. 7 - The power loss, P, in a journal bearing depends on...Ch. 7 - The thrust of a marine propeller is to be measured...Ch. 7 - The rate dT/dt at which the temperature T at the...Ch. 7 - When a valve is closed suddenly in a pipe with...Ch. 7 - An airship is to operate at 20 m/s in air at...Ch. 7 - An airplane wing of 3 m chord length moves through...Ch. 7 - A flat plate 1.5 m long and 0.3 m wide is towed at...Ch. 7 - This 1:12 pump model using water at 15C simulates...Ch. 7 - An ocean-going vessel is to be powered by a...Ch. 7 - On a cruise ship, passengers complain about the...Ch. 7 - A 1:3 scale model of a torpedo is tested in a wind...Ch. 7 - A flow rate of 0:18 m3/s of water at 20C...Ch. 7 - A force of 9 N is required to tow a 1:50 ship...Ch. 7 - An airplane wing, with chord length of 1.5 m and...Ch. 7 - A water pump with impeller diameter of 24 in. is...Ch. 7 - A model hydrofoil is to be tested at 1:20 scale....Ch. 7 - A ship 120 m long moves through freshwater at 15C...Ch. 7 - A 1:30 scale model of a cavitating overflow...Ch. 7 - In some speed ranges, vortices are shed from the...Ch. 7 - A 1:8 scale model of a tractor-trailer rig is...Ch. 7 - On a cruise ship, passengers complain about the...Ch. 7 - When a sphere of 0.25 mm diameter and specific...Ch. 7 - The flow about a 150 mm artillery projectile which...Ch. 7 - Your favorite professor likes mountain climbing,...Ch. 7 - A 1:50-scale model of a submarine is to be tested...Ch. 7 - Consider water flow around a circular cylinder, of...Ch. 7 - A 1:10 scale model of a tractor-trailer rig is...Ch. 7 - The power, P, required to drive a fan is assumed...Ch. 7 - Over a certain range of air speeds, V, the lift,...Ch. 7 - The pressure rise, p, of a liquid flowing steadily...Ch. 7 - An axial-flow pump is required to deliver 0.75...Ch. 7 - A model propeller 1 m in diameter is tested in a...Ch. 7 - Consider Problem 7.38. Experience shows that for...Ch. 7 - Closed-circuit wind tunnels can produce higher...Ch. 7 - A 1:16 model of a bus is tested in a wind tunnel...Ch. 7 - The propagation speed of small-amplitude surface...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Use Mohrs circle to determine the normal stress and shear stress acting on the inclined plane AB.
Mechanics of Materials (10th Edition)
Three rigid bodies, 2,3, and 4, are connected by four springs as shown in the figure. A horizontal force of 1,0...
Introduction To Finite Element Analysis And Design
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
If FB = 3 kN and = 45, determine the magnitude of the resultant force of the two tugboats and its direction me...
Engineering Mechanics: Statics
The inside surface temperature of a window in a room is 40 F (4 C) where the air has a temperature of 72 F (22 ...
Heating Ventilating and Air Conditioning: Analysis and Design
When 2000 L/min of water flows through a circular section with an inside diameter of 300 mm that later reduces ...
Applied Fluid Mechanics (7th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its bearing is found to be dependent on the force F normal to the shaft, the speed of rotation N of the shaft, the dynamic viscosity of the oil, and the shaft diameter D. Establish a correlation among these variables by using dimensional analysis.arrow_forward3. In a fuel injection system, small droplets are formed due to the breakup of the liquid jet. Assume the droplet diamter, d, is a function of the liquid density, p, viscosity, μ and surface tension, σ, and the jet velocity, V, and diamter, D. Form an appropriate set of dimensionless parameters using μ, V, and D as repeating variables. (Ans: =(VV)). μarrow_forwardAn airplane wing model is designed with a similarity test. the sustaining force is a function of speed, chord, density, viscosity, speed of sound and angle of attack. determine the dimensionless numbersarrow_forward
- The water resistance (drag) R on the submarine Nautilus is a function of its length L, velocity v of the ship, viscosity μ, and density ρ of the water in which it moves. Determine dimensionless groups that could be used to organize test data.arrow_forwardQuestion 3 The power, P, to drive an axial pump is in a function of density of fluid, p, volumetric flow rate, Q, pump head, h, diameter of rotor, D, and angular speed of rotor, N. (a) (b) (c) P PDS N3 Verify that - is a dimensionless group. Determine the remaining pi group and perform dimensional analysis. Define geometric similarity and dynamic similarity. Categorize the pi group obtained from part (b) as geometric similarity or dynamic similarity, respectively.arrow_forward4 Discharge, Q through a venturimeter depends on the following variable Inlet pipe diameter - D Throat diameter - d Pressure drop across the venturimeter - Ap Fluid density - P Dynamic viscosity - µ Using MLT set of dimensions evaluate the dimensionless parameters correlating this phenomenon 5 The droplet size, D produced by a liquid spray nozzle depends on the following variable Nozzle diameter - d Jet velocity - U Fluid density - p Dynamic viscosity – u Surface tension - o Using MLT set of dimensions evaluate the dimensionless parameters correlating this phenomenonarrow_forward
- 5. The drag force, fd, on a sphere located in a pipe through which a fluid is flowing is to be determined experimentally. Assume that the drag is a function of the sphere diameter, d, the pipe diameter, D, the fluid velocity, V, and the fluid density, p. (a) What dimensionless parameters would you use for this prob- lem? (b) Some experiments using water indicate that for d = 0.2in., D = 0.5in, and V = 2ft/s, the drag is 1.5 x 10-3lb. Estimate the drag on a sphere located in a 2 - ft-diameter pipe through which water is flowing with a velocity of 6ft/s. The sphere diameter is such that geometric similarity is maintained. (Ans: 31.11b) Spherearrow_forwardThe pressure coefficient is defined by the ratio between the static pressure difference and the dynamic pressure (pictured): Where P is the static pressure [Pa], P∞ is the reference static pressure [Pa], ρ is the density [kg/m3], and V is the velocity [m/s]. Using the primary dimensions and their units, show that the pressure coefficient is dimensionless.arrow_forward20 The efficiency of a fan depends on the density p, the dynamic viscosity μ of the fluid, the angular velocity , diameter D of the rotor and the discharge Q. Express n in terms of dimensionless parameters.arrow_forward
- The power P required for operating a pump depends on the diameter of the pump D, the pressure rise Ap across the pump, the fluid density p, the fluid viscosity and the Theorem, and D, Q and p as the repeating variables, the dimensionless group associated with μ is given by volume flow rate Q through the pump. Using Buckingham's μDªQbpº. Determine the values of a, b and c. 1. [0.99, 1.01 2. [-1.01, 0.99 3. [-1.01, -0.99 a= b = C=arrow_forwardSpeed is usually a function of density, gravitational acceleration, diameter, height difference, viscosity, and length. Using the repetitive variables method and taking density, gravitational acceleration, and diameter as repetitive variables, find the required dimensionless parameters. V = f(p, g, D, Az, u, L)arrow_forwardAn incompressible fluid oscillates harmonically (V = Vosinut, where Vis the velocity) with a frequency of 9 rad/s in a 6-in.-diameter pipe. A 1/5 scale model is to be used to determine the pressure difference per unit length, Ap, (at any instant) along the pipe. Assume that Api= f(D, Vo, w, t, u, p) where D is the pipe diameter, w the frequency, t the time, the u fluid viscosity, and p the fluid density. If the same fluid is used in the model and the prototype, at what frequency should the model operate? Wm i rad/sarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Unit Conversion the Easy Way (Dimensional Analysis); Author: ketzbook;https://www.youtube.com/watch?v=HRe1mire4Gc;License: Standard YouTube License, CC-BY