Programmable Logic Controllers
5th Edition
ISBN: 9780073373843
Author: Frank D. Petruzella
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 7, Problem 2RQ
Program Plan Intro
a.
- The main purpose of mechanical timing relays is to delay the opening and closing of contacts for circuit control.
- Its operation is almost similar to that of a control relay.
- The only difference is that the contacts of a mechanical timing relay are used to operate at a preset time interval, that is, after the coil is energized or de-energized.
- One example for mechanical timing relay is Pneumatic timing relay.
- There are two different arrangements for mechanical timing relays, such as on-delay timer and off-delay timer.
- Each type will have different kinds of contacts such as closed contacts and open contacts.
Explanation of Solution
b.
Normally Closed Timed Open (NCTO) contact:
The symbol used to represent a NCTO contact is given below.
Explanation of Solution
c.
Normally Open Timed Open (NOTO) contact:
The symbol used to represent a NOTO contact is given below.
- NOTO contact is an off-delay time based contact...
Explanation of Solution
d.
Normally Closed Timed Closed (NCTC) contact:
The symbol used to represent a NCTC contact is given below.
- NCTC contact is an off-delay time based contact...
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
2. Draw the timing diagram for the Clocked SR flip-flop at each of the instants t0 to t6 as described in the class meeting.
a. at t0, Q is low, S is low, R is low
b. at t0, Q is high, S is low, R is low
Be sure to include the clock signal in the timing diagram.
* the state diagram for the following timing diagram is
CK
a/1
/PS Z
e/0
a/1
b/0
f/1
0/p
c/0
e/1
c/0
0/P
B O
A
1
a/1
g/0
b/0
f/1
1
e/1
c/0
1
d/0
None of the above O
C
Computer Science
Find the resistor value to create a timer for 100 second using 0.002 F CapacitorMulti Line Text.
Chapter 7 Solutions
Programmable Logic Controllers
Ch. 7 - Prob. 1RQCh. 7 - Prob. 2RQCh. 7 - Prob. 3RQCh. 7 - Prob. 4RQCh. 7 - a. What are the two methods commonly used to...Ch. 7 - Prob. 6RQCh. 7 - Prob. 7RQCh. 7 - Prob. 8RQCh. 7 - For a TOF timer: a. When is the enable bit of a...Ch. 7 - Explain what each of the following quantities...
Ch. 7 - State the method used to reset the accumulated...Ch. 7 - Study the ladder logic program in Figure 7-40 and...Ch. 7 - Study the ladder logic program in Figure 7-42, and...Ch. 7 - Prob. 6PCh. 7 - Prob. 7PCh. 7 - Prob. 8PCh. 7 - Prob. 9PCh. 7 - Prob. 10PCh. 7 - Prob. 11PCh. 7 - Prob. 13PCh. 7 - When the lights are turned off in a building, an...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- Design a 1-minute timer using a 60 Hz power line as an interrupting source. The output ports should display minutes and seconds in BCD. At the end of the minute, the output ports should continue displaying one minute and zero seconds.arrow_forwardDraw an ASM chart for the synchronous circuit having the following description, "The circuit has a control input X. clock and outputs A and B. If X = 1, on every clock rising edge the code on BA changes from 00 01 10 →1100 and repeats. If X=0, the circuit holds the present state.".arrow_forwardexplain GA-Based Clock-Timing Adjustmentarrow_forward
- A taco generator is use as a sensor to detect the speed of a rotating motor. The o/p of the tacho is between Ov and 5v where the midrange (2.5v) is equivalent to that the motor is standstill. When motor accelerates CW toward full speed, the tacho o/p will vary from 2.5v to 5v and when the input of tacho varies from 2.5v down to Ov means the motor is accelerating towards cCW. The Scenario is to reflect the equivalent speed on two SSDS which one will read the equivalent speed of reading 5 for maximum Cw (5v) and the other will also read 5 for maximum CCW (Ov) equivalent speed in the reverse direction. Taco generator input is connected to PA4, the CW SSD on PORTB and the CCW SD on PORTC Write ATmega 16 program sketch to follow the above scenario REFS1 REFSO Voltage Reference Selection AREF, Internal Vref turned off AVCC with external capacitor at AREF pin 1 Reserved 1 Internal 2.56V Voltage Reference with external capacitor at AREF pin ADPS2 ADPS1 ADPSO Division Factor 2 1 1 1 1 16 1 32 1…arrow_forwardDefine timing parameters: tWR, tWC, tCO, tRD, tRC.arrow_forwardGiven the D flip-flop frequency divider shown, a. If the Clock signal has a frequency of 100 MHz, what frequency is at the output, A1? b. Finish the timing diagram assuming the D flip flops change state on the positive edge of the clock input (i.e., positive edge triggered). Clock AO A1 Clock AO A1arrow_forward
- Describe the clock generator in simple terms.arrow_forward1. Draw the timing diagram of the inputs S, R, and output Q given the x, y, z inputs and the SR Latch below. Assume that Q = 0 (initially). N S R O X Z Da D Qarrow_forwardConsider the following T flip flop timing diagram: What type of clock trigger is used? Clk Q No Correct answer Falling Edge Trigger Rising Edge Trigger Falling and Risingarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- EBK JAVA PROGRAMMINGComputer ScienceISBN:9781305480537Author:FARRELLPublisher:CENGAGE LEARNING - CONSIGNMENTSystems ArchitectureComputer ScienceISBN:9781305080195Author:Stephen D. BurdPublisher:Cengage Learning
EBK JAVA PROGRAMMING
Computer Science
ISBN:9781305480537
Author:FARRELL
Publisher:CENGAGE LEARNING - CONSIGNMENT
Systems Architecture
Computer Science
ISBN:9781305080195
Author:Stephen D. Burd
Publisher:Cengage Learning