(a)
The value of mean free path
(a)
Answer to Problem 37P
The value of mean free path
Explanation of Solution
Given:
The resistivity is
The Fermi energy from Table 38-1 is
The value of
Formula used:
The expression of resistivity from equation 38-13 is,
The expression for Fermi speed is,
Calculation:
From equation (1), the mean free path is,
Substitute values in above expression,
Conclusion:
Therefore, the value of mean free path
(b)
The value of scattering cross section area.
(b)
Answer to Problem 37P
The value of scattering cross section area is
Explanation of Solution
Formula used:
The expression for mean free path from equation 38-16 is,
Here,
From equation (3), the scattering cross section area is,
Substitute values in above equation,
Conclusion:
Therefore, the value of scattering cross section area is
Want to see more full solutions like this?
Chapter 38 Solutions
Physics for Scientists and Engineers
- A more general definition of the temperature coefficient of resistivity is α =1ρ|dρdT|where ρ is the resistivity at temperature T. (a) Assuming α is constant, show that ρ = ρ0eα(T−T0) where ρ0 is the resistivity at temperature T0. (b) Using the series expansion ex ≈ 1 + x for x << 1, show that the resistivity is given approximately by the expression ρ = ρ0[1 + α(T − T0)] for α(T − T0) ≪ 1arrow_forwardA nichrome rod of length LN = 78 cm is connected in series (end to end) to a carbon rod of length LC = 5 cm. Both rods have cross-sectional areas of A = 85 mm2. At T0 = 20° C the restistivity of nichrome is ρN = 1.50 × 10-6 Ω⋅m and the resistivity of carbon is ρC = 3.50 × 10-5 Ω⋅m. The temperature coefficient of nichrome is positive with value αN = 0.4 × 10-3 °C-1. The temperature coefficient of carbon is negative with a value αC = -0.5 × 10-3 °C-1. The nonlinear dependence of the resistivity on temperature T can be written as ρ = ρ0eα(T-T0). A) Write an expression for the total resistance of the nichrome-carbon combination as a function of temperature in terms of quantities given in the introduction. Simplify your answer as much as possible. B) Calculate the temperature in degrees Celsius for which the resistance of the carbon-nichrome combination will be a minimum C) Calculate the value of the minimum resistance, in ohms.arrow_forwardConsider a copper wire with a diameter of 2.75 mm. A. What is the drift speed of the electrons in the copper wire when a current of 13.0 A flows through it? Assume that each copper atom contributes one free electron to the metal. The density of copper is 8.92 g/cm3. B. How does this drift speed compare to the random rms speed of an electron at 20.0°C? To make this comparison, determine the random rms speed of an electron at 20.0°C using the ideal gas model and find the ratio of the two speeds.arrow_forward
- A wire with cross-sectional area "A", length "l" and conductivity "σ" is subjected to a potential difference "V". The applied potential difference is changed and the wire is stretched so that the power dissipated increases by a factor of 30 and the current increases by a factor of 4.Find the ratio of the final length "l" to the initial length "lo" of the wirearrow_forwardAn iron wire has a cross - sectional area of 5.00 x 10-6 m2.Carry out steps (a) through (e) to compute the drift speed ofthe conduction electrons in the wire. (a) How many kilogramsare there in 1 mole of iron? (b) Starting with the density of ironand the result of part (a), compute the molar density of iron(the number of moles of iron per cubic meter). (c) Calculatethe number density of iron atoms using Avogadro’s number.(d) Obtain the number density of conduction electrons giventhat there are two conduction electrons per iron atom. (e) Ifthe wire carries a current of 30.0 A, calculate the drift speed ofconduction electrons.arrow_forwardConsider a power plant is located 60 km away from a residential area uses Q-gauge (A=42.40mm2) wire ofcopper to transmit power at a current of I = 100.00 A.How much more power is dissipated in the copper wires than it would be in superconducting wires?arrow_forward
- A nichrome rod of length LN = 78 cm is connected in series (end to end) to a carbon rod of length LC = 5 cm. Both rods have cross-sectional areas of A = 85 mm2. At T0 = 20° C the resistivity of nichrome is ρN = 1.50 × 10-6 Ω⋅m and the resistivity of carbon is ρC = 3.50 × 10-5 Ω⋅m. The temperature coefficient of nichrome is positive with a value αN = 0.4 × 10-3 °C-1. The temperature coefficient of carbon is negative with a value αC = -0.5 × 10-3 °C-1. The nonlinear dependence of the resistivity on temperature T can be written as ρ = ρ0eα(T-T0). A)Write an expression for the total resistance of the nichrome-carbon combination as a function of temperature in terms of quantities given in the introduction. Simplify your answer as much as possible. Answer to part A is r(t)= ( ( ρC LC )/A ) eαC ( T - T0 ) + ( ( ρN LN )/A ) eαN ( T - T0 ) B) Calculate the temperature in degrees Celsius for which the resistance of the carbon-nichrome combination will be a minimum. C) Calculate the…arrow_forwardA copper wire of 3.2 mm in diameter and 4 m length carries a certain amount of current. The conductionelectron density in copper is 8.49x1028 electrons/m3. A 75.0-Ω resistor is connected with the copper wireto the terminals of a battery whose emf is 11.0 V and whose internal resistance is 0.8 Ω. Calculate (a) thecurrent in the circuit, (b) the current density in the wire, (c) the terminal voltage of the battery, Vab, and (d)the power dissipated in the resistor R, (e) the power dissipated in the battery’s internal resistance r, (f) the resistivity of the wire, (g) the drift velocity of the free electrons, and (h) Estimate the rms speed ofelectrons assuming they behave like an ideal gas at 20°C. Assume that one electron per Cu atom is free tomove (the others remain bound to the atom).arrow_forwardCalculate the specific conductivity of the conductor in Mega(Ωm)-1 since the current passing through a conductor with a cross-section (1.00nm x 1.00µm), length of 10.00mm, is 1.00mA and the voltage value falling on it is 1.00V.arrow_forward
- The figure gives the electric potential V(x) along a copper wire carrying uniform current, from a point of higher potential Vs = 14.0 μV at x = 0 to a point of zero potential at xs = 3.00 m. The wire has a radius of 2.10 mm, and copper has a resistivity of 1.69 × 10-8 Ω·m. What is the current in the wire?arrow_forwardResistivity in metals increases with temperature according to the equation: ρ(T) = ρ0[1 + α(T - T0)] where α is the temperature coeficcient of restivity, and ρ0 is the restivity at the reference temperature T0. For a particular wire, the temperature coeficcient of restivity is α = 3.83 X 10-3 °C-1, and the restivity is ρ0 = 7.71 X 10-7 Ωm at the reference temperature T0 = 297°C. Find an expression for the temperature T2, at which the resistance of a particular wire will be twice as high as it is at the reference temperature T0. (Both temperatures are in degrees Celsius) Use this expression to find the temperature in degrees Celsius for T2. If the wire has a length of 1.00m and it has a circular cross section with a radius of 1.00cm, what is the resistance in ohms, at a temperature which is twice the reference temperature, T = 2T0 ?arrow_forwardIn a normal conductor heat is generated at a rate I 2R. Therefore a current-carrying conductor must dissipate heat effectively or it can melt or overheat the device in which it is used. Consider a long cylindrical copper wire (resistivity 1.72x 10-8 Ω*m) of diameter 0.75 mm. If the wire can dissipate 80 W/m2 along its surface, what is the maximum current this wire can carry?arrow_forward
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning