Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 31, Problem 51SDP
To determine
Referring to Fig. 14.11b, could you use any of the processes described in Chapters 30 and 31 to make a large bolt by welding the head to the shank? Explain the advantages and limitations of this approach.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
2) Explain how a cylindrical joint can be practically realised?
List Down Three (3) Categories of Joining Processes and Compare Them.
What do you understand by the term welded joint? How it differs from riveted joint?
Chapter 31 Solutions
Manufacturing Engineering & Technology
Ch. 31 - Explain what is meant by solid-state welding.Ch. 31 - What is cold welding? Why is it so called?Ch. 31 - What is (a) a ferrule, (b) filled gold, and (c) a...Ch. 31 - What are faying surfaces in solid-state welding...Ch. 31 - What is the basic principle of (a) ultrasonic...Ch. 31 - Explain how the heat is generated in the...Ch. 31 - Prob. 7RQCh. 31 - Describe the principle of resistance-welding...Ch. 31 - Prob. 9RQCh. 31 - What type of products are suitable for stud...
Ch. 31 - Prob. 11RQCh. 31 - Prob. 12RQCh. 31 - Prob. 13RQCh. 31 - Describe how high-frequency butt welding operates.Ch. 31 - What materials are typically used in...Ch. 31 - Make a list of processes in this chapter,...Ch. 31 - Prob. 17QLPCh. 31 - Explain the reasons why the processes described in...Ch. 31 - Explain the similarities and differences between...Ch. 31 - Describe your observations concerning Figs....Ch. 31 - Would you be concerned about the size of weld...Ch. 31 - What advantages does friction welding have over...Ch. 31 - Prob. 23QLPCh. 31 - Prob. 24QLPCh. 31 - Discuss the factors that influence the strength of...Ch. 31 - What are the sources of heat for the...Ch. 31 - Can the roll-bonding process be applied to a...Ch. 31 - Prob. 28QLPCh. 31 - List and explain the factors involved in the...Ch. 31 - Give some of the reasons that spot welding is...Ch. 31 - Prob. 31QLPCh. 31 - Prob. 32QLPCh. 31 - Prob. 33QLPCh. 31 - Prob. 34QLPCh. 31 - Prob. 35QLPCh. 31 - Prob. 36QLPCh. 31 - Prob. 37QLPCh. 31 - Prob. 38QLPCh. 31 - Which processes in this chapter are not affected...Ch. 31 - Consider the situation where two round...Ch. 31 - Prob. 41QLPCh. 31 - The energy required in ultrasonic welding is found...Ch. 31 - Prob. 43QTPCh. 31 - Prob. 44QTPCh. 31 - Prob. 45QTPCh. 31 - Prob. 46SDPCh. 31 - Explain how you would fabricate the structures...Ch. 31 - Prob. 48SDPCh. 31 - Prob. 49SDPCh. 31 - Prob. 50SDPCh. 31 - Prob. 51SDPCh. 31 - Prob. 52SDPCh. 31 - Prob. 53SDPCh. 31 - Describe the methods you would use for removing...Ch. 31 - Prob. 55SDPCh. 31 - Prob. 56SDPCh. 31 - Inspect the sheet-metal body of an automobile,...Ch. 31 - Prob. 59SDPCh. 31 - Prob. 60SDPCh. 31 - Sketch the microstructure you would expect if a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Why is cost a consideration in joint design?arrow_forward(b) A resistance welding is performed to join two 2-mm thick stainless steel sheets with ten 6-mm diameter spot welds produced concurrently. The resulted weld nugget each has average 3 mm in thickness. Calculate the required welding current and energy consumption for the welding if ten seconds are needed for the whole welding operation. Given that the applied voltage is 10 V. Provide 00 TWO important assumptions in your calculation.arrow_forwardA resistance welding is performed to join two 2-mm thick stainless steel sheets with ten 6-mm diameter spot welds produced concurrently. The resulted weld nugget each has average 3 mm in thickness. Calculate the required welding current and energy consumption for the welding if ten seconds are needed for the whole welding operation. Given that the applied voltage is 10 V. Provide TWO important assumptions in your calculation.arrow_forward
- Select TWO (2) arc welding processes that are suitable for performing rapid welding task especially for thick materials.arrow_forwardA 40 mm diameter solid shaft is to be welded to a flat plate and is required to carry a torque of 2000 Nm. If fillet joint is used foe welding what will be the minimum size of the weld when working shear stress is 76 MPa.arrow_forwardEnumerate the different types of riveted joints and rivets.arrow_forward
- 17) C. Discuss any five differences between the soft soldering and hard soldering process used in joining of metalsarrow_forward2. A flexible, round, plain-opening pipe removes welding fumes. The pipe is 8 in. in diameter and is positioned so the pipe face is 8 in. from the welding operation. Assume the capture velocity produced is 200 ft/min at the point of welding. (a) What is the flow rate in the pipe? (b) Estimate the velocity at the face of the pipe.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Metal Joining Process-Welding, Brazing and Soldering; Author: Toc H Kochi;https://www.youtube.com/watch?v=PPT5_fDSzGY;License: Standard YouTube License, CC-BY