Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 31, Problem 44QTP
To determine
Estimate the temperature rise in problem 31.43. It is considered that the temperature has a uniform distribution and the heat generated is confined to the volume of material directly between the two round electrodes.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A circular electrode of 190 mm diameter is used for carrying out seam welding at 5 welds per cm on a mild steel tube of thickness 1.5 mm. The duration of the welding
cycle is given as On - 4 cycles, Off- 3 cycles. The power supply is at 50 Hz. Calculate work speed, welds per minutę, RPM, and energy requirement assuming effective
resistance between an electrode as 100u ohm.
It is desired to determine the cost of the submerged arc welding operation in the preceding problem, including electric power cost but excluding work material costs. Power during arc-on time = 9,000 W, and cost of electricity = $0.15/kWH. The labor cost rate = $33.00/hr and the SAW equipment cost = $20.00/hr (including applicable overheads). The cost of each spool of electrode wire = $50.00. The cost of granular flux used in each cycle = $2.00. What is the welding cost of each completed tube?
Two 1.2 mm thick flat copper sheets are being spot welded using a current of 6000A and a current flow time of 0.18 s. The electrodes are 5 mm in diameter. Estimate the generated in the weld zone. Take effective resistance as 150 ohm. also calculate temperature rise assuming that the heat generated is confined to the volume ogf materials directly between two electrodes and temperature is uniformly distributed.
Chapter 31 Solutions
Manufacturing Engineering & Technology
Ch. 31 - Explain what is meant by solid-state welding.Ch. 31 - What is cold welding? Why is it so called?Ch. 31 - What is (a) a ferrule, (b) filled gold, and (c) a...Ch. 31 - What are faying surfaces in solid-state welding...Ch. 31 - What is the basic principle of (a) ultrasonic...Ch. 31 - Explain how the heat is generated in the...Ch. 31 - Prob. 7RQCh. 31 - Describe the principle of resistance-welding...Ch. 31 - Prob. 9RQCh. 31 - What type of products are suitable for stud...
Ch. 31 - Prob. 11RQCh. 31 - Prob. 12RQCh. 31 - Prob. 13RQCh. 31 - Describe how high-frequency butt welding operates.Ch. 31 - What materials are typically used in...Ch. 31 - Make a list of processes in this chapter,...Ch. 31 - Prob. 17QLPCh. 31 - Explain the reasons why the processes described in...Ch. 31 - Explain the similarities and differences between...Ch. 31 - Describe your observations concerning Figs....Ch. 31 - Would you be concerned about the size of weld...Ch. 31 - What advantages does friction welding have over...Ch. 31 - Prob. 23QLPCh. 31 - Prob. 24QLPCh. 31 - Discuss the factors that influence the strength of...Ch. 31 - What are the sources of heat for the...Ch. 31 - Can the roll-bonding process be applied to a...Ch. 31 - Prob. 28QLPCh. 31 - List and explain the factors involved in the...Ch. 31 - Give some of the reasons that spot welding is...Ch. 31 - Prob. 31QLPCh. 31 - Prob. 32QLPCh. 31 - Prob. 33QLPCh. 31 - Prob. 34QLPCh. 31 - Prob. 35QLPCh. 31 - Prob. 36QLPCh. 31 - Prob. 37QLPCh. 31 - Prob. 38QLPCh. 31 - Which processes in this chapter are not affected...Ch. 31 - Consider the situation where two round...Ch. 31 - Prob. 41QLPCh. 31 - The energy required in ultrasonic welding is found...Ch. 31 - Prob. 43QTPCh. 31 - Prob. 44QTPCh. 31 - Prob. 45QTPCh. 31 - Prob. 46SDPCh. 31 - Explain how you would fabricate the structures...Ch. 31 - Prob. 48SDPCh. 31 - Prob. 49SDPCh. 31 - Prob. 50SDPCh. 31 - Prob. 51SDPCh. 31 - Prob. 52SDPCh. 31 - Prob. 53SDPCh. 31 - Describe the methods you would use for removing...Ch. 31 - Prob. 55SDPCh. 31 - Prob. 56SDPCh. 31 - Inspect the sheet-metal body of an automobile,...Ch. 31 - Prob. 59SDPCh. 31 - Prob. 60SDPCh. 31 - Sketch the microstructure you would expect if a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Calculate the electrode tip diameter if the thickness of low carbon steel type of material is 1.2mm.arrow_forwardYour boss requests a recommendation on which process to use to weld the high strength structural steel rail tank cars hull section. You have this additional information: P-GMAW Productivity is substantially lower. However, you have welders already qualified to do manual p-GMAW welding. Labor is 80% of total cost HYPERFILLⓇ® Productivity gains are important, and the volume of the product is sufficient on the rail tank cars to justify capital investment. With confidence, you respond: Use process because .(Give process and short explanation for why you want to use that process)arrow_forwardExample 27.2. A 100 mm x 10 mm plate is to be 150 mm x 10 mm by the fillet welding on three sides. The size of the weld is 6 mm. Find out the necessary over lap of the plate, for full strength of the joint. Take allowable tensile stress in plate equal to 150 N/mm and allowable stress in weld as 110 N/mm. welded to another platearrow_forward
- In one type of welding, electric charge flows between the welding tool and the metal pieces that are to be joined. This produces a glowing arc whose high temperature fuses the pieces together. Why must the tool be held close to the metal pieces? (i) To maximize the potential difference between tool and pieces; (ii) to minimize this potential difference; (iii) to maximize the electric field between tool and pieces; (iv) to minimize this electric field; (v) more than one of these.arrow_forwardCalculate the heat input during the arc welding process, if the voltage is 33 volts, current is 115 amperes, the length of the weld is 88mm and the time to complete the weld 34 secs.arrow_forwardTwo 1.2 mm thick sheets of steel are joined by double-sided spot welding using a current of 6000A and current flow time of t = 0.15 sec. The electrodes are 3 mm in diameter and the weld spot thickness is approximately one third of the total thickness of the metal sheets. Assuming that the effective resistance in this operation is 200 micro resistance, estimate the heat generated and its distribution in the weld zone. (Take density of steel = 8600 Kg/m3 and its latent heat capacity, L =1400 J/g)arrow_forward
- A resistance welding is performed to join two 2-mm thick stainless steel sheets with ten 6-mm diameter spot welds produced concurrently. The resulted weld nugget each has average 3 mm in thickness. Calculate the required welding current and energy consumption for the welding if ten seconds are needed for the whole welding operation. Given that the applied voltage is 10 V. Provide TWO important assumptions in your calculation.arrow_forward(b) A resistance welding is performed to join two 2-mm thick stainless steel sheets with ten 6-mm diameter spot welds produced concurrently. The resulted weld nugget each has average 3 mm in thickness. Calculate the required welding current and energy consumption for the welding if ten seconds are needed for the whole welding operation. Given that the applied voltage is 10 V. Provide 00 TWO important assumptions in your calculation.arrow_forwardA GTAW operation is performed on low carbon steel, whose unit melting energy is 10.3 J/mm3. The welding voltage is 22 volts and the current is 135 amps. The heat transfer factor is 0.7 and the melting factor is 0.65. If filler metal wire of 3.5 mm diameter is added to the operation, the final weld bead is composed of 60% volume of filler and 40% volume base metal. If the travel speed in the operation is 5 mm/sec, determine (a) cross-sectional area of the weld bead, and (b) the feed rate (mm/sec) at which the filler wire must be supplied.arrow_forward
- A shielded metal arc-welding operation is performed on austenitic stainless steel at a voltage = 25 volts and a current = 200 A. The heat transfer factor = 0.92, and the melting factor = 0.60. The unit melting energy of medium-carbon steel is 137 Btu/in3. Determine the (a) power in the operation, (b) rate of heat generation at the weld and (c) volume rate of metal welded.arrow_forwardA welding operation is time-studied during which an operator was pace-rated as 120%. The operator took, on an average, 8 minutes for producing the weld-joint. If a total of 10% allowances are allowed for this operation. What is the expected standard production rate of the weld-joint in units per 8 hour day?arrow_forwardA 40 mm diameter solid shaft is to be welded to a flat plate and is required to carry a torque of 2000 Nm. If fillet joint is used foe welding what will be the minimum size of the weld when working shear stress is 76 MPa.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Metal Joining Process-Welding, Brazing and Soldering; Author: Toc H Kochi;https://www.youtube.com/watch?v=PPT5_fDSzGY;License: Standard YouTube License, CC-BY