Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 26, Problem 29QLP
Describe the effects of a wear flat on the overall grinding operation.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
PLEASE SUMMARIZE IT IN YOUR WORDS!
11) An internal bore is ground to 100 mm, removing 0.3 mm stock. To accomplish
this, a grinding wheel 80% of the finished size is used. The wheel is dressed every
15 cycles because it is observed that the radial wheel wear is 0.05 mm on average.
Assume wheel and part widths are equal.
a. What dressing depth would you recommend and why?
b. Calculate the G-ratio of this operation.
. Briefly explain the working of a centerless grinding operation with a neat sketch?
Chapter 26 Solutions
Manufacturing Engineering & Technology
Ch. 26 - What is an abrasive? What are superabrasives?Ch. 26 - How is the size of an abrasive grain related to...Ch. 26 - Why are most abrasives made synthetically?Ch. 26 - Describe the structure of a grinding wheel and its...Ch. 26 - Explain the characteristics of each type of bond...Ch. 26 - What causes grinding sparks in grinding? Is it...Ch. 26 - Define metallurgical burn.Ch. 26 - Define (a) friability, (b) wear flat, (c) grinding...Ch. 26 - What is creep-feed grinding and what are its...Ch. 26 - How is centerless grinding different from...
Ch. 26 - What are the differences between coated and bonded...Ch. 26 - What is the purpose of the slurry in...Ch. 26 - Explain why grinding operations may be necessary...Ch. 26 - Why is there such a wide variety of types, shapes,...Ch. 26 - Prob. 15QLPCh. 26 - The grinding ratio, G, depends on the type of...Ch. 26 - What are the consequences of allowing the...Ch. 26 - Explain why speeds are much higher in grinding...Ch. 26 - Prob. 19QLPCh. 26 - Prob. 20QLPCh. 26 - Prob. 21QLPCh. 26 - Referring to the preceding chapters on processing...Ch. 26 - Explain the reasons that so many deburring...Ch. 26 - What precautions should you take when grinding...Ch. 26 - Prob. 25QLPCh. 26 - What factors could contribute to chatter in...Ch. 26 - Prob. 27QLPCh. 26 - Prob. 28QLPCh. 26 - Describe the effects of a wear flat on the overall...Ch. 26 - What difficulties, if any, could you encounter in...Ch. 26 - Prob. 31QLPCh. 26 - Prob. 32QLPCh. 26 - Prob. 33QLPCh. 26 - Jewelry applications require the grinding of...Ch. 26 - List and explain factors that contribute to poor...Ch. 26 - Calculate the chip dimensions in surface grinding...Ch. 26 - If the strength of the workpiece material is...Ch. 26 - Assume that a surface-grinding operation is being...Ch. 26 - Estimate the percent increase in the cost of the...Ch. 26 - Assume that the energy cost for grinding an...Ch. 26 - It is known that, in grinding, heat checking...Ch. 26 - Prob. 45QTPCh. 26 - With appropriate sketches, describe the principles...Ch. 26 - Prob. 47SDPCh. 26 - Vitrified grinding wheels (also called ceramic...Ch. 26 - Conduct a literature search, and explain how...Ch. 26 - Visit a large hardware store and inspect the...Ch. 26 - Obtain a small grinding wheel or a piece of a...Ch. 26 - In reviewing the abrasive machining processes in...Ch. 26 - Obtain pieces of sandpaper and emery cloth of...Ch. 26 - On the basis of the contents of this chapter,...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Explain why the same grinding wheel may act soft or hard.arrow_forward13) Manufacturers are designing grinding spindles to turn at higher and higher speeds. What is the main reason for this, and what is one drawback of increasing speed? 14) Name 2 reasons why cost increases as finish allowances decrease (See Figure 9.40).arrow_forwardDefine trueing and creep feed grinding.arrow_forward
- c) It is planned to carry out the grinding operation using a grinding wheel of diameter 15 cm and width 2 cm, and using successive depths of cut of 0.02 mm, with two final cuts of 0.01 mm each. Wheel speed is 1450 m/min, work speed is 0.25 m/s and the cross feed is 0.4 mm. The number of active grits per area of the wheel surface is 0.75 grits/mm? with a grain aspect ratio of 20. i) Determine the Material Removal Rates for both depths of cut. ii) If the cycle time for one forward/return stroke of the work during grinding is 5 sec., estimate the total time taken to complete the job. ii) Considering a constant of proportionality K2 of 40,000, determine the maximum surface temperature of the work. iv) What recommendations would you give to reduce any surface damage owing to high work temperatures?arrow_forwardWhy Centerless Grinding machine uses two grinding wheels during grinding? Type your Answer here:-arrow_forwardManufacturers are designing grinding spindles to turn at higher and higher speeds. What is the main reason for this, and what is one drawback of increasing speed? Name 2 reasons why cost increases as finish allowances decrease. Tool temperatures are low at low cutting speeds and high at high cutting speeds, but low again at even higher cutting speeds. Explain why.arrow_forward
- Rod Mills, Ball Mills and Autogenous Mills are different types of tumbling mills used in the metalliferous industry. What equipment, if any, usually accompanies each of these mills in grinding circuits and why.arrow_forwardi need the answer quicklyarrow_forwardFind metal removal rate is sur face grinding a(300mm) long and (60mm) width of rectangulare steel work Piece whose speed is (15 m/min) defth of (cut and width of grinding Pathz lomm? = 0.05mm) of Oarrow_forward
- 5. Types of Grinding Wheel Machines and their outputs. (atleast 3)arrow_forwardWhat wheel shapes are commonly used for surface and cylindrical grinding?arrow_forwardI want the theory part about Batch grinding in ball mill, its types, its Applications, advantages and disadvantages and els PLZ I want a perfect answer with detailsarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Types of Manufacturing Process | Manufacturing Processes; Author: Magic Marks;https://www.youtube.com/watch?v=koULXptaBTs;License: Standard Youtube License