(a)
The equilibrium composition of the product gases from combustion of liquid propane.
(a)
Answer to Problem 38P
The equilibrium composition of the product gases from combustion of liquid propane is
Explanation of Solution
Write the stoichiometric equation for combustion of 1 kmol of liquid propane
Write the chemical reaction equation for dissociation of carbon dioxide.
Write the formula to calculate the equilibrium constant
Here, number of moles of
Conclusion:
The stoichiometric coefficients from the Equation (II),
Balance for
Re-write the actual combustion equation for the combustion of 1 kmol of liquid propane
Calculate the total number of moles of products
From the Table A-28 of “Natural logarithms of the equilibrium constant
Substitute
Substitute 3 for
Thus, the equilibrium composition of the product gases from combustion of liquid propane is
(b)
The amount of heat transfer for the combustion of liquid propane.
(b)
Answer to Problem 38P
The amount of heat transfer for the combustion of liquid propane is
Explanation of Solution
Write the energy balance equation to determine the heat transfer
Here, number of moles of products is
Write the expression to calculate the molar flow rate of liquid propane
Here, mass flowrate of propane is
Write the expression to calculate the rate of heat transfer
Conclusion:
Rewrite the Equation (V) for the combustion of liquid propane.
Here, enthalpy of formation at
From the Table A-18 through Table A-26, obtain the enthalpies of vaporization and enthalpies of formation for different substances as in Table 1.
Substance |
Enthalpy of vaporization |
Enthalpy of formation at 285 K |
Enthalpy of formation at 298 K |
Enthalpy of formation at 1200 K |
- | - | - | ||
0 | 8696.5 | 8682 | 38,447 | |
0 | 8286.5 | 8669 | 36,777 | |
- | 9904 | 44,380 | ||
- | 9364 | 53,848 |
Substitute
Substitute
Substitute
Thus, the amount of heat transfer for the combustion of liquid propane is
Want to see more full solutions like this?
Chapter 16 Solutions
Thermodynamics: An Engineering Approach
- A cylindrical specimen of aluminum is pulled in tension. Use the stress v. strain plot below for this specimen of Al to answer parts (a) - (f). Hint: Each strain increment is 0.004. Be sure to include your engineering problem solving method per the class rubric. 400 350 300 250 Stress (MPa) 200 150 100 50 Aluminum (Stress v. Strain) 0 0 0.02 0.04 0.06 0.08 Strain 0.1 0.12 0.14 0.16 a. Compute the modulus of elasticity. b. Determine the yield strength at a strain offset of 0.002. c. Determine the tensile strength of this metal. d. Compute the ductility in percent elongation. e. Compute the modulus of resilience. f. Determine the elastic strain recovery for an unloaded stress of 340 MPa.arrow_forwardConsider a single crystal of silver oriented such that a tensile stress is applied along a [112] direction. If slip occurs on a (011) plane and in a [111] direction and is initiated at an applied tensile stress of 15.9 MPa, compute the critical resolved shear stress.arrow_forwardA hypothetical component must not fail when a tensile stress of 15.25 MPa is applied. Determine the maximum allowable internal crack length if the surface energy of the component is 1.50 J/m2. Assume a modulus of elasticity of 350 GPa.arrow_forward
- Fresh air at 21.1 C in which partial pressure of water vapor is 0.018 atmosphere is blown at the rate of 214 m3/h first through a preheater and then adiabatically saturated in spray chambers to 100% saturation and again reheated this reheated air has humidity of 0.024 kg water vapor per kg dry air. It is assumed that the fresh air and the air leaving the re-heater have the same percentage humidity. Determine:- a- The temperature of preheater, spray-chamber and re-heater b- Heat requirement for preheating and re-heating 11:39 مarrow_forwardThe answer to the problem is 7.24 N. Please show me how to get the final answerarrow_forwardThe answer to the problem is 17.9N. Please show me how to get the final answerarrow_forward
- The answer to the problem is 2.93 ft/s. Please show me how to get the final answerarrow_forwardExample(3): 0.15 kg/s steam at atmospheric pressure and superheated to 400 K is bled into an air stream at 320 K and 20 per cent relative humidity. What is the temperature, enthalpy, and relative humidity of the mixed stream if the air is flowing at 5 kg/ s? How much steam would be required to provide an exit temperature of 330 K and what would be the humidity of this mixture? 11:39 مarrow_forwardThe answer to the problem is 31.3rad/s. Please show me how to get the final answerarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY