Materials Science And Engineering Properties
1st Edition
ISBN: 9781111988609
Author: Charles Gilmore
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 12, Problem 1CQ
To determine
The quantity which is equal in both matrix and reinforcing phase when a force is applied parallel to a reinforcing phase of a composite material.
Expert Solution & Answer
Answer to Problem 1CQ
Thestrainis equal in both matrix and reinforcing phase when a force is applied parallel to a reinforcing phase of a composite material.
Explanation of Solution
The composite material is a combination of two or more materials together to reinforce the properties of base material. In a composite material the matrix phase is reinforced or surrounded by second phase to provide unique properties like conductivity, strength, wear resistance etc. to composite.
When a force is applied to a reinforced phase, a strain developed in both the matrix and reinforcing phase. The developed strain is considered to be equal in magnitude for both the matrix and reinforce material.
When a force is applied to the reinforced phase, due to the stress developed, the material with very low strain to fracture will fails first. The failure is due to the fact that the phases of composite material would have same strain.
Conclusion:
Thus, thestrainis equal in both matrix and reinforcing phase when a force is applied parallel to a reinforcing phase of a composite material.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
A composite beam is made of two brass [E - 111 GPa] bars bonded to two aluminum [E - 72 GPa] bars, as shown. The beam is
subjected to a bending moment of 250 N-macting about the z axis. Using a - 10 mm, b- 65 mm, c- 20 mm, and d- 45 mm, calculate
(a) the maximum bending stress in the aluminum bars.
(b) the maximum bending stress in the brass bars.
Aluminum
Brass
Brass
Aluminum
Answers:
(a) Oa
i
MPa
(b) Oer
MPa
Save for Later
Attempts: 0 of 1 used
Submit Answer
A composite bar is rigidly attached to the wall at A as shown, Axial loads are applied at the positions indicated.
-Determine axial stress in member AB (in MPa unit)
- Determine the displacement of joint C (in mm unit)
-Determine the deformation in member BC (in mm unit)
A composite beam is made of two brass (E =110GPa) to two aluminum bars (E = 70GPa), as shown. The beam is subjected to a bending moment of 380 N-m acting about the z-axis. Using a = 5mm, b = 40mm, c = 10mm, and d = 25mm. Calculate:
a) the maximum bending stress in the aluminum bars
b) the maximum bending stress in the brass bars
Chapter 12 Solutions
Materials Science And Engineering Properties
Ch. 12 - Prob. 1CQCh. 12 - Prob. 2CQCh. 12 - Prob. 3CQCh. 12 - Prob. 4CQCh. 12 - Prob. 5CQCh. 12 - Prob. 6CQCh. 12 - Prob. 7CQCh. 12 - Prob. 8CQCh. 12 - Composite _________ is produced by laying fibers...Ch. 12 - Prob. 10CQ
Ch. 12 - Prob. 11CQCh. 12 - Prob. 12CQCh. 12 - Prob. 13CQCh. 12 - Prob. 14CQCh. 12 - Prob. 15CQCh. 12 - Prob. 16CQCh. 12 - Prob. 17CQCh. 12 - Prob. 18CQCh. 12 - Prob. 19CQCh. 12 - Prob. 20CQCh. 12 - Prob. 21CQCh. 12 - Prob. 22CQCh. 12 - Prob. 23CQCh. 12 - Prob. 24CQCh. 12 - Prob. 25CQCh. 12 - Prob. 26CQCh. 12 - Prob. 27CQCh. 12 - Prob. 28CQCh. 12 - Prob. 1ETSQCh. 12 - Prob. 2ETSQCh. 12 - Prob. 3ETSQCh. 12 - Prob. 4ETSQCh. 12 - Prob. 5ETSQCh. 12 - Prob. 6ETSQCh. 12 - Prob. 7ETSQCh. 12 - Prob. 8ETSQCh. 12 - Prob. 9ETSQCh. 12 - Prob. 10ETSQCh. 12 - In Example Problem 12.1, a uniaxial composite...Ch. 12 - Prob. 12.2PCh. 12 - Prob. 12.3PCh. 12 - Prob. 12.4PCh. 12 - Prob. 12.5PCh. 12 - Prob. 12.6PCh. 12 - Estimate the transverse tensile strength of the...Ch. 12 - Prob. 12.8PCh. 12 - Prob. 12.9PCh. 12 - Prob. 12.10PCh. 12 - Prob. 12.11PCh. 12 - Prob. 12.12PCh. 12 - Prob. 12.13PCh. 12 - Prob. 12.14PCh. 12 - Prob. 12.15PCh. 12 - Prob. 12.16PCh. 12 - Prob. 12.17P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- Q2: A composite beam is made of two brass [E =100 GPa] plates bonded to an aluminum [E =75 GPa] bar, as shown in Figure below. The beam is subjected to a bending moment of 1200 N-m acting about the z axis. Determine: (a)the maximum bending stresses in the brass plates and the aluminum bar. (b) the stress in the brass at the joints where the two materials are bonded together.arrow_forwardA composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 73 GPa] bars, as shown. The beam is subjected to a bending moment of 445 N-m acting about the z axis. Using a = 15 mm, b = 125 mm, c = 30 mm, and d = 75 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Z Aluminum C Aluminum Answers: (a) Ogl Brass (b) Obr= i i b Brass a MPa MPaarrow_forwardA composite beam is made of two brass [E = 99 GPa] plates bonded to an aluminum [E = 72 GPa] bar, as shown. The beam is subjected to a bending moment of 2010 N-m acting about the z axis. Assume b-44 mm, d₁-37 mm, d₂-11 mm. Determine: (a) the maximum bending stresses Obr, al in the brass plates and the aluminum bar. (b) the stress in the brass brj at the joints where the two materials are bonded together. Brass (2) Aluminum (1) Brass (2) Answers: (a) Obr = (b) Obrj = i b d₂ d₁ MPa, oal = MPa. MPa.arrow_forward
- PROBLEM 6.56 50 mm A steel bar and an aluminum bar are bonded together as shown to form a composite beam. Knowing that the vertical shear in the beam is 18 kN and that the modulus of elasticity is 200 GPa for the steel and 73 GPa for the aluminum, determine (a) the average stress at the bonded surface, (b) the maximum stress Aluminum 25 mm Steel in the beam. 36 mmarrow_forwardA composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 70 GPa] bars, as shown. The beam is subjected to a bending moment of 400 N-m acting about the z axis. Using a = 15 mm, b = 100 mm, c = 30 mm, and d = 65 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Aluminum y Brass Aluminum b Brass C a darrow_forwardA composite beam is made of two brass [E = 112 GPa] bars bonded to two aluminum [E = 69 GPa] bars, as shown. The beam is subjected to a bending moment of 350 N-m acting about the z axis. Using a = 15 mm, b = 115 mm, c = 25 mm, and d = 65 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Z Aluminum с Aluminum Answers: (a) Jal= (b) Obr= Brass i y i b Brass a a MPa MPaarrow_forward
- 1.0 The composite shaf, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. Determine the displacement of end A with respect to end and the normal stress in each section. The cross sectional area and modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C. Also, determine the displacement of B with respect to C of the composite shaft. Aluminum Copper Eeu = 18(10°) ksi ABC = 0.12 in? Steel E = 10(103) ksi AAB = 0.09 in? E = 29(103) ksi AcD = 0.06 in? 3.75 kip 2.00 kip 3.00 kip 1.50 kip BL 3.75kip D 2.00kip 18 in.- 12 in.- 16 in:arrow_forwardA composite beam is made of two brass [E = 110 GPa] bars bonded to two aluminum [E = 71 GPa] bars, as shown. The beam is subjected to a bending moment of 260 N-m acting about the z axis. Using a = 10 mm, b = 85 mm, c = 20 mm, and d = 55 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Aluminum С Aluminum Answers: (a) Jal= Brass (b) Obr= i b Brass a MPa MPaarrow_forwardA composite beam is made of two brass [E = 110 GPa] bars bonded to two aluminum [E = 71 GPa] bars, as shown. The beam is subjected to a bending moment of 260 N-m acting about the z axis. Using a = 10 mm, b = 85 mm, c = 20 mm, and d = 55 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. 2 Aluminum C Aluminum Answers: (a) Jal= Brass- (b) Obr= i i b Brass (2 (2 MPa O MPa Earrow_forward
- Determine the maximum moment of inertia of the composite figure shown below, in mm^4.arrow_forward3 For a composite bar as shown below, what is the relation between axial deformation and thermal deformations in the bar? Cu tube (1) Steel bar (2) D d- Where, o,, o, = stresses in Cu and steel bar respectively. Coefficient of thermal expansion for Cu and steel bar respectively.arrow_forwardThe composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. The cross-sectional areas of sections AB, BC, and CD are AAB = 0.08 in², ABC = 0.11 in², and Acp = 0.06 in², respectively. The modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning
The History of Composite Materials, From Brick to Bakelite to Biomimetic Hybrids; Author: Autodesk;https://www.youtube.com/watch?v=VS_Kg-VEvzE;License: Standard YouTube License, CC-BY