A composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 70 GPa] bars, as shown. The beam is subjected to a bending moment of 400 N-m acting about the z axis. Using a = 15 mm, b = 100 mm, c = 30 mm, and d = 65 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. N Aluminum y Brass Aluminum b Brass d a

A composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 70 GPa] bars, as shown. The beam is subjected to a bending moment of 400 N-m acting about the z axis. Using a = 15 mm, b = 100 mm, c = 30 mm, and d = 65 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. N Aluminum y Brass Aluminum b Brass d a

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Required information A steel bar (Es = 210 GPa) and an aluminum bar (Ea = 70 GPa) are bonded together to form the composite bar shown. 8 mm Steel 8 mm 8 mm Aluminum 24 mm Determine the maximum stress in aluminum when the bar is bent about a horizontal axis, with M= 66 N-m. The maximum stress in aluminum is MPа.
A composite beam is made of two brass [E = 110 GPa] bars bonded to two aluminum [E = 71 GPa] bars, as shown. The beam is subjected to a bending moment of 260 N-m acting about the z axis. Using a = 10 mm, b = 85 mm, c = 20 mm, and d = 55 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Aluminum С Aluminum Answers: (a) Jal= Brass (b) Obr= i b Brass a MPa MPa
The composite bar shown is firmly attached to unyielding supports. An axial load P= 200 kN is applied at 20°C. Assume a = 11.7 um/(m °C) for steel and 23.0 um'(m °C) for aluminum. Find the reaction at the left support. a. find the reaction at the left supportb.find the stress at the steelc. find the stress at the aluminum
A flat bar of aluminum alloy 25 mm wide and 5 mm thick is placed between two steel bars each 25 mm wide and 10 mm thick to form a composite bar 25 mm x 25 mm as shown. The three bars are fastened together at their ends when the temperature is 15℃. Find the stress in each of the materials when the temperature of the whole assembly is raised to 55 ℃.Steel: Es = 200 GPa; Coefficient of expansion = 1.2x10^-5/℃.Aluminum: Eal = 200/3 GPa; Coefficient of expansion = 2.3x10-5/℃.
A composite beam is made of two brass (E =110GPa) to two aluminum bars (E = 70GPa), as shown. The beam is subjected to a bending moment of 380 N-m acting about the z-axis. Using a = 5mm, b = 40mm, c = 10mm, and d = 25mm. Calculate: a) the maximum bending stress in the aluminum bars b) the maximum bending stress in the brass bars
Q2: A composite beam is made of two brass [E =100 GPa] plates bonded to an aluminum [E =75 GPa] bar, as shown in Figure below. The beam is subjected to a bending moment of 1200 N-m acting about the z axis. Determine: (a)the maximum bending stresses in the brass plates and the aluminum bar. (b) the stress in the brass at the joints where the two materials are bonded together.
Problem 2: A bronze bar is fastened between a steel bar and an aluminum bar as shown. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel Bronze 480 mm² 650 mm² 3P 1.0 m 4P 2.0 m Aluminum 320 mm² 1.5 m 2P
A composite beam is made of two brass [E = 97 GPa] plates bonded to an aluminum [E = 72 GPa] bar, as shown. The beam is subjected to a bending moment of 2420 N-m acting about the z axis. Assume b=64 mm, d1=36 mm, d2=13 mm. Determine: (a) the maximum bending stresses opy,Gal in the brass plates and the aluminum bar. (b) the stress in the brass obrj at the joints where the two materials are bonded together. Brass (2) d2 Aluminum (1) Brass (2) dz b Answers: (a) obr = i MPa, oal = i MPа. (b) Obrj MPa.
A composite beam is made of two brass [E = 96 GPa] plates bonded to an aluminum [E = 62 GPa] bar, as shown. The beam is subjected to a bending moment of 2260 N-m acting about the z axis. Assume b=53 mm, d1=48 mm, d2=14 mm. Determine:(a) the maximum bending stresses σbrσb⁢r, σalσa⁢l in the brass plates and the aluminum bar.(b) the stress in the brass σbrjσb⁢r⁢j at the joints where the two materials are bonded together.
The critical bending compressive stress in the extreme fibre of a structural steel section is 1000 MPa. It is given that the yield strength of the steel is 250 MPa, width of flange is 250 mm and thickness of flange is 15 mm. As per the provisions of IS: 800 -2007, the non-dimensional slenderness ratio of the steel cross-section is (a) 0.25 (c) 2.00 (b) 0.75 (d) 0.50
A composite beam is made of two brass [E - 111 GPa] bars bonded to two aluminum [E - 72 GPa] bars, as shown. The beam is subjected to a bending moment of 250 N-macting about the z axis. Using a - 10 mm, b- 65 mm, c- 20 mm, and d- 45 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Aluminum Brass Brass Aluminum Answers: (a) Oa i MPa (b) Oer MPa Save for Later Attempts: 0 of 1 used Submit Answer
An aluminum alloy [E = 74 GPa; v = 0.33; a = 23.0 x 10-6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 265 mm, a cross-sectional area of A = 5300 mm², and a length of L= 4.2 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by AT = 57°C, the longitudinal normal strain in the plate is found to be 2920 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Ad. L P Answer: (a) P = i (b) Δd = i kN mm