PROBLEM 6.56 Aluminum 50 mm A steel bar and an aluminum bar are bonded together as shown to form a composite beam. Knowing that the vertical shear in the beam is 18 kN and that the modulus of elasticity is 200 GPa for the steel and 73 GPa for the aluminum, determine (a) the average stress at the bonded surface, (b) the maximum stress 25 mm Steel in the beam. 36 mm

PROBLEM 6.56 Aluminum 50 mm A steel bar and an aluminum bar are bonded together as shown to form a composite beam. Knowing that the vertical shear in the beam is 18 kN and that the modulus of elasticity is 200 GPa for the steel and 73 GPa for the aluminum, determine (a) the average stress at the bonded surface, (b) the maximum stress 25 mm Steel in the beam. 36 mm

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.4P

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
Problem 1.5-2 A bar of length 2.0 m is made of a structural stoel having the stres-strain dingram shown in the figure. The yield stresa of the steel is 250 MPa and the slope of the initial lincar part of the stress-strain curve (modulus of elasticity) is 200 GP. The bar is loaded axially until it eklongates 6.5 mm, and then the load is removod. How does the final length of the bar compare with its orig- inal length? Hint: Ue the concepts illustrated in Fig. 1-36h) MP 300 200 100 0.002 0.004 0.006
An aluminum alloy [E = 73 GPa; v = 0.33; a= 23.0 x 10-6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 250 mm, a cross-sectional area of A = 6900 mm², and a length of L = 5.9 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by AT = 50°C, the longitudinal normal strain in the plate is found to be 2400 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Ad. L Answer: (a) P = i (b) Δd = KN mm
An aluminum alloy [E = 74 GPa; v = 0.33; a = 23.0 x 10-6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 265 mm, a cross-sectional area of A = 5300 mm², and a length of L= 4.2 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by AT = 57°C, the longitudinal normal strain in the plate is found to be 2920 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Ad. L P Answer: (a) P = i (b) Δd = i kN mm
The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests, it has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑y 40 40 MPa 80 MPa 25 MPa ➜X
A steel bar with diameter d1 = 10 mm has upset ends with diameter d2 = 15 mm. The lengths of the bar segments are L1=0.3 m and L2=0.15 m. The radius at the transition R = 1.25 mm and the modulus of elasticity is 90 GPa, the bar product of the load p elongates 0.12 mm maximum stress
A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for high cycle fatigue, o, x N = C, (where the stress amplitude is in MPa). Ignore the geometric detail and assume that Marin's modifying factors are all equal to 1. You are given the minimum stress ain = -213 MPa, the maximum stress omax = 213 MPa. The material data are Tensile strength oUTS = 539 MPa, Basquin's constant c, = 875 MPa, Basquin's exponent a = 0.085. a) Calculate the stress ratio R, the stress amplitude o, in MPa and the mean stress am in MPa. The answers are acceptable with a tolerance of 0.01 for R and of 1 MPa the stresses. R: MPa MPа b) Calculate the corresponding life, in 10° cycles, (tolerance of 0.1 106 cycles) N :
A steel bar with diameter d1 = 10 mm has upset ends with diameter d2 = 15 mm. The lengths of the bar segments are L1=0.3 m and L2=0.15 m. The radius at the transition R = 1.25 mm and the modulus of elasticity is 90 GPa, the bar product of the load p elongates 0.12 mm normal stress and maximum stress
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²