Materials for Civil and Construction Engineers (4th Edition)
4th Edition
ISBN: 9780134320533
Author: Michael S. Mamlouk, John P. Zaniewski
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Question
Chapter 11, Problem 11.5QP
To determine
Why are fibers much stronger than the bulk material and give an example of a material.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
(a) What is the effect of increasing the carbon content in steel on each of the each of the following items?
1. Yield strength
2. Modulus of elasticity
3. Ductility
(b) Materials are generally classified into three categories based on the predominant types of bond. What are these three categories
and what are the predominant types of bond in each category? For each category, provide two examples of common materials used
by civil engineers.
Why are fibers much stronger than the bulk material? Give an example of a material that is relatively weak in the bulk form and very strong in the fiber form.
A cylindrical specimen of brass that has a diameter of 20 mm, a tensile modulus of 110 GPa, and a Poisson's ratio of 0.35 is pulled in
tension with force of 40,000 N. If the deformation is totally elastic, what is the strain experienced by the specimen?
O 0.00463
O 0.00116
O 0.0029
O 0.01350
Chapter 11 Solutions
Materials for Civil and Construction Engineers (4th Edition)
Ch. 11 - Prob. 11.1QPCh. 11 - Prob. 11.2QPCh. 11 - Prob. 11.3QPCh. 11 - Prob. 11.4QPCh. 11 - Prob. 11.5QPCh. 11 - Prob. 11.6QPCh. 11 - Prob. 11.7QPCh. 11 - Prob. 11.8QPCh. 11 - Prob. 11.9QPCh. 11 - What are the functions of aggregate used in...
Ch. 11 - Prob. 11.11QPCh. 11 - Prob. 11.12QPCh. 11 - What are the benefits of adding dispersed steel...Ch. 11 - Getting measurements from Figure 11.20, determine...Ch. 11 - Three 6 in. 12 in. concrete cylinders with...Ch. 11 - Prob. 11.16QPCh. 11 - Prob. 11.17QPCh. 11 - Prob. 11.18QPCh. 11 - Prob. 11.19QPCh. 11 - Prob. 11.20QPCh. 11 - Prob. 11.21QPCh. 11 - Prob. 11.22QPCh. 11 - Prob. 11.23QPCh. 11 - Prob. 11.24QPCh. 11 - Prob. 11.25QPCh. 11 - Prob. 11.26QPCh. 11 - Prob. 11.27QPCh. 11 - Prob. 11.28QPCh. 11 - Prob. 11.29QPCh. 11 - Prob. 11.30QPCh. 11 - A circular FRP composite rod with continuous and...
Knowledge Booster
Similar questions
- The frame of a space shuttle type vehicle must have a high yield strength and high stillness, and the most important design factor is weight. Of all the materials presented in this chapter, what material might be the most suitable for the frame of a space shuttle? Assume that there will be both tensile and compressive stresses. For a space shuttle, cost is not a limiting factor. (a) You can eliminate entire classes of materials from consideration with a brief statement about their unsuitability. (b) What material has the highest specific yield strength? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (c) What material has the highest specific elastic modulus? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (d) Compare the materials with the highest specific yield strength and highest specific elastic modulus for suitability in the space shuttle frame. (C) Discuss the suitability of the top-rated material for this design from the viewpoint of the ability to produce a frame.arrow_forwardWhich of the following terms indicate "the ability of the material to not to undergo change in shape when loads are applied" a. Weldability b. Formability c. Conductivity d. Rigidityarrow_forwardA 100 mm x 100 mm x 100 mm cube made with glass polymers in the y- direction is subjected to a tensile load of 100 kN along the y-direction. However, the cube is constrained against deformation in the x and z directions. Given the following properties: Ex = 20 GPa Ey = 50 GPa Ez = 20 GPa Vxy = 0.25 Vxz = 0.5 Vyz = 0.25 (a) Compute for the change in length of the cube in the y-direction and; (b) Determine the stresses, ox,Oy,Oz•arrow_forward
- A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and a diameter of 0.38 inches the rest. If it is subjected to a tensile load of 6,000 lbs, what will be the tótal deformation of the bar if it has a modulus of elasticity E= 28.5 x 10^6 psi. %3D O 0.1378 inches O 0.1338 inches O 0.1352 inches O 0.1364 inches O 0.1423 inchesarrow_forwardA combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa Allowable compressive stress 140 MPa 70 MPa Which of the following most nearly gives the load, in percent, carried by the copper? Select the correct response: 44.44% 55.56% 66.67% O33.33%arrow_forwardTo stretch a 200 mm long tensile test specimen (a) of steel elastically by 0.08 mm. How many loads do I need to apply? (b) What is the maximum length of this sample without plastic deformation? How long can it be extended? (The modulus of elasticity of steel is 210 GPa, yield strength 580 MPa, tensile strength 920 MPa specified as.arrow_forward
- On the stress-strain diagram of a steel bar, show and explain the following: proportional limit, yield stress, ultimate stress, yield strain, and modulus of elasticity.arrow_forwardWhich materials tend to exhibit elastic perfectly plastic behavior?arrow_forwardstrength of material subject columns chapter about reduction factor, in working stressarrow_forward
- A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa Allowable compressive stress 140 MPa 70 MPa If the allowable strain for both materials is 0.0005, which of the following most nearly gives the maximum load the member can carry so that this allowable strain is not exceeded? Select the correct response 162.00 kN 185.00 kN 205.00 kN 175.00 kNarrow_forwardWhat is the value of reduction factor of the beam, if the stress in the steel is 400 MPa, and the Modulus of Elasticity of the Steel is 200,000 MPa. O 0.671 0.692 O 0.660 O 0.650 None of the Choices O 0.681arrow_forwardA flat bar of aluminum alloy 25 mm wide and 5 mm thick is placed between two steel bars each 25 mm wide and 10 mm thick to form a composite bar 25 mm x 25 mm as shown. The three bars are fastened together at their ends when the temperature is 15℃. Find the stress in each of the materials when the temperature of the whole assembly is raised to 55 ℃.Steel: Es = 200 GPa; Coefficient of expansion = 1.2x10^-5/℃.Aluminum: Eal = 200/3 GPa; Coefficient of expansion = 2.3x10-5/℃.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Construction Materials, Methods and Techniques (M...Civil EngineeringISBN:9781305086272Author:William P. Spence, Eva KultermannPublisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning
Construction Materials, Methods and Techniques (M...
Civil Engineering
ISBN:9781305086272
Author:William P. Spence, Eva Kultermann
Publisher:Cengage Learning