Materials for Civil and Construction Engineers (4th Edition)
4th Edition
ISBN: 9780134320533
Author: Michael S. Mamlouk, John P. Zaniewski
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 11, Problem 11.26QP
(a)
To determine
The modulus of elasticity of the reinforced concrete.
(b)
To determine
The load carried by the each of the steel and plain concrete.
(c)
To determine
The minimum required cross sectional area of the column.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A short reinforced concrete column is subjected to a 600 kips axial compressive load. The moduli of elasticity of plain concrete and steel are 5 * 106 psi and 30 * 106 psi, respectively, and the cross-sectional area of steel is 1.8% of that of the reinforced concrete. Considering the column as a structural member made of a composite material and subjected to load parallel to the steel rebars, calculate the following:a. the modulus of elasticity of the reinforced concreteb. the load carried by each of the steel and plain concretec. the minimum required cross-sectional area of the column, given that the allowable compressive stress of plain concrete is 5000 psi and that the allowable compressive stress of plain concrete will be reached before that of steel
A short reinforced concrete column is subjected to a 1000 kN axial compressive load. The moduli of elasticity of plain concrete and steel are 25 and207 GPa, respectively, and the cross-sectional area of steel is 2% of that of thereinforced concrete. Considering the column as a structural member made of a composite material and subjected to load parallel to the steel rebars, calculate the following:a. the modulus of elasticity of the reinforced concreteb. the load carried by each of the steel and plain concretec. the minimum required cross-sectional area of the column given that the allowable compressive stress of plain concrete is 20 MPa and that the allowable compressive stress of plain concrete will be reached before that of steel.
A representative reinforced concrete composite beam section is shown in the figure below. The number of reinforcement is 6 and the diameter of the reinforcement is 16 meters. cross section Determine the neutral axis (x) and calculate the maximum normal stresses that will occur in concrete and steel. It will be assumed that the concrete does not carry tensile stress. The modulus of elasticity of the steel is 200000 Mpa. The modulus of elasticity of concrete is 28000 Mpa. The section width is b= 400 mm. Take the cover as 50 mm.
(The maximum bending moment acting on the section is 59 kNm and d= 700 mm.)
Chapter 11 Solutions
Materials for Civil and Construction Engineers (4th Edition)
Ch. 11 - Prob. 11.1QPCh. 11 - Prob. 11.2QPCh. 11 - Prob. 11.3QPCh. 11 - Prob. 11.4QPCh. 11 - Prob. 11.5QPCh. 11 - Prob. 11.6QPCh. 11 - Prob. 11.7QPCh. 11 - Prob. 11.8QPCh. 11 - Prob. 11.9QPCh. 11 - What are the functions of aggregate used in...
Ch. 11 - Prob. 11.11QPCh. 11 - Prob. 11.12QPCh. 11 - What are the benefits of adding dispersed steel...Ch. 11 - Getting measurements from Figure 11.20, determine...Ch. 11 - Three 6 in. 12 in. concrete cylinders with...Ch. 11 - Prob. 11.16QPCh. 11 - Prob. 11.17QPCh. 11 - Prob. 11.18QPCh. 11 - Prob. 11.19QPCh. 11 - Prob. 11.20QPCh. 11 - Prob. 11.21QPCh. 11 - Prob. 11.22QPCh. 11 - Prob. 11.23QPCh. 11 - Prob. 11.24QPCh. 11 - Prob. 11.25QPCh. 11 - Prob. 11.26QPCh. 11 - Prob. 11.27QPCh. 11 - Prob. 11.28QPCh. 11 - Prob. 11.29QPCh. 11 - Prob. 11.30QPCh. 11 - A circular FRP composite rod with continuous and...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- For the cross section shown below, the material and sectional properties are given as follows: Determine the modular ratio. The concrete modulus of elasticity can be estimated by [psi] where must be in unit psi. (b) Draw the transformed section. (C) Show that the cross-section is elastic and does not have cracks when a bending moment of 1,000 kips-in is applied. Also, given the bending moment, find the maximum stress in concrete and steel. The neutral axis is at 11.05 in. from the top surface, and the moment of inertia around the neutral axis is 26676 in4.arrow_forwardA short reinforced concrete column is subjected to a 1000 kN axial compressive load. Themoduli of elasticity of plain concrete and steel are 25 GPa and 207 GPa, respectively, and thecross-sectional area of steel is 2% of that of the reinforced concrete. Considering the columnas a structural member made of a composite material and subjected to load parallel to the steelrebars, calculate the following:a) The modulus of elasticity of the reinforced concreteb) The load carried by each of the steel and plain concretec) The minimum required cross-sectional area of the column given that the allowablecompressive stress of plain concrete is 20 MPa and that the allowable compressivestress of plain concrete will be reached before that of steelarrow_forwardThe cross-section of the reinforced concrete beam having an effective depth of 500 mm is shown in the figure (not drawn to the scale). The grades of concrete and steel used are M35 and Fe550, respectively. The area of tension reinforcement is 400 mm?. It is given that the corresponding to 0.2% proof stress, the material safety factor is 1.15 and the yield strain of Fe550 steel is 0.0044. 500 mm 100 mm 200 mm 0 A, = 400 mm? As per IS 456:2000, the limiting depth (in mm, round off to nearest integer) of the neutral axis measured from the extreme compression fiber, is ww 00arrow_forward
- Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 28 MPa and steel yield strength fy = 420 MPa. 1. if the tensile strain is εs = fy/Es upon crushing of concrete at a strain of 0.003. = (5 decimal places) 2. if the tensile strain is set as 0.010 upon crushing of concrete at a strain of 0.003. = (5 decimal places) 3. Minimum as required by NSCP 2015. = (5 decimal places)arrow_forwardThe composite bar in the figure is stress-free before the axial loads P1 and P2 are applied. Assuming that the walls are rigid, calculate the stress in each material if P1 = 150 kN and P2 = 90 kN.arrow_forwardThe modulus of elasticity of "reinforced concrete" in RC design, is O A. 420 GPa B. 200 GPa C. None () D. 220 GPaarrow_forward
- 1. Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is % X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is o=20.0 ksi, the allowable shear stress for the rivets is o=25.0 ksi and the allowable bearing stress on the rivets and splice plates is o=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded? Splice Plates a-0.75 in Bar Lc =0.80 in. Bar P d = 1.0 in. b=4.0 in. Rivets 'e = 6.0 in.arrow_forwardQ.2. The stress-strain diagram of a reinforcement steel having a cross-sectional diameter of 12 mm diameter and 100 mm gage length is determined after its tensile strength test as follows. Based on the stress- strain diagram determine the followings properties of the material (Poisson's ratio of the material is 0.32) : 600 a) Modulus of elasticity 550 500 b) Yield strength 450 c) Toughness 400 350 d) Resilience 300 e) Shear modulus 250 200 f) Bulk modulus 150 g) Ductility as described by 100 percent change in length 50 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1 0.11 0.12 0.13 0.14 0.15 0.16 0.17 0.18 Strain Note: Show your methods and calculations clearly. Stress, MPaarrow_forward14. The composite bar in the figure is stress-free before the axial loads PI and P2 are applied. Assuming that the left wall is rigid, while the right wall yields 0.80mm. calculate the stress in each material if PI = 150 kN and P2 = 90 kN. Aluminum Steel 150 kN 500 mm Bronze 1 90 KN 250 mm 350 mm 0.8 mmarrow_forward
- 4 Why is reinforced concrete so popular in building construction projects? 5 Why are the steel rods placed below and as far away as possible from the neutral axis in a reinforced concrete beam? 6 The cross section of a reinforced concrete beam is shown below. It has a modular ratio of 15. If the allowable compressive stress in the concrete is 6 MPa and the allowable tensile stress in the steel is 120 MPa, determine diameter of the three reinforcing steel rods to make the beam an economic section. 550 mm 75 200arrow_forwardThe composite bar in the figure is stress-free before the axial loads P₁ and P2 are applied. Assuming that the walls are rigid, calculate the stress in each material if P₁= 150 kN and P₂ = 90 kN. Aluminum Steel Bronze A = 900 mm² A = 2000 mm² A = 1200 mm² E = 70 GPa E = 200 GPa E = 83 GPa P₁ 500 mm P₂ 250 mm 350 mm (a) Determine the stress in the aluminum. (b) Determine the stress in the steel. (c) Determine the stress in the bronze.arrow_forwardA RECTANGULAR ALUMINUM BLOCK IS 40mm LONG IN THE Y DIRECTION, 20mm WIDE IN THE Z DIRECTION AND 25mm THICK IN THE X DIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF A UNIFORMLY DISTRIBUTED FORCE OF Px=3 (COMPRESSION), Py=6 (TENSION) AND Pz=9 (COMPRESSION) IN THE X, Y AND Z DIRECTIONS RESPECTIVELY. IF THE POISSON’S RATIO = 1/4 & E = 70 GPa, DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSO DETRMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THE WOULD PRODUCE THE SAME X DEFORMATION AS THE ORIGINAL.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Structural Analysis (10th Edition)Civil EngineeringISBN:9780134610672Author:Russell C. HibbelerPublisher:PEARSONPrinciples of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
- Fundamentals of Structural AnalysisCivil EngineeringISBN:9780073398006Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel LanningPublisher:McGraw-Hill EducationTraffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Structural Analysis (10th Edition)
Civil Engineering
ISBN:9780134610672
Author:Russell C. Hibbeler
Publisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Fundamentals of Structural Analysis
Civil Engineering
ISBN:9780073398006
Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning
Publisher:McGraw-Hill Education
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning