State three examples of a static load application and three examples of a dynamic load application.
State three examples of static load application and three examples of dynamic load application.
Explanation of Solution
Static load application:
It indicates a constant loading of building over an extensive time period. Static loads do not generate any blow or shaking on the building. The examples of this load are car parked at a carpark, the weight of building acting on the surface of the ground, and the force acting on a beam.
Dynamic load application:
Dynamic loads acting on the buildings are those that produce a vibration or a blow on the building. Dynamic loads are imposed on the building for a small time interval. The examples of this load are force due to boring of bore holes, weight of a moving car on the road, and weight due to working equipment.
Want to see more full solutions like this?
Chapter 1 Solutions
Materials for Civil and Construction Engineers (4th Edition)
Additional Engineering Textbook Solutions
Foundation Design: Principles and Practices (3rd Edition)
Concepts Of Programming Languages
C Programming Language
Starting Out with Java: Early Objects (6th Edition)
Starting Out With Visual Basic (7th Edition)
Objects First with Java: A Practical Introduction Using BlueJ (6th Edition)
- According to Figure 5-20, is ii possible to completely separate one of the four materials from the other three? Explain your answer.arrow_forwardThis is a question from mechanics of material book (axial load chapter). I need the correct solution please, it is very important and answers I have seen are vary.arrow_forwardA piece of steel wire 100 feet long, with a cross-sectional area of 0.004 aq. in., must be stretched with a pull of 16 pounds when in use . if the modulus of elacticity of steel is 30,000 psi: a) what is the total elognation in the entire length of the wire? b) what tensile stress is producted by the pull?arrow_forward
- The force P is applied on the top of the solid cylindrical body which rests on a circular cap as shown below. Determine the smallest dimensions d1, d3, and t required to support the load P. Use the table given below and your student ID to obtain the values of the force P and the allowable stresses for all the materials used in the problem (i.e., P and the allowable stresses are givenarrow_forwarda. Why you are studying the course of Mechanics of Materials and explain your learned concepts? b. Discuss the basic difference among Normal, Shearing and Bearing Stress.arrow_forwardSHOW COMPLETE ANSWER AND ILLUSTRATION FINAL ANSWER IN 3 DECIMAL PLACES Problem 4: A steel bar 50 mm in diameter and 2 m long is surrounded by a shell of castiron 5 mm thick. Compute the load that will compress the combined bar a total of 1 mm. For steel, E = 200 GPa, and for cast iron, E = 100 GPa.arrow_forward
- Briefly explain dead loads, live loads and impact loads with reference to loads on a structure.arrow_forwardFind the bulk modulus of elasticity of a liquid of pressure 150 psi applied to 10 ft^3 of the liquid causes a volume reduction of 0.02 ft^3.arrow_forwardA part’s maximum Von Mises stress and materials are given below. Determine for each of these conditions whether the part is safe or not. Material: Steel, Von Mises Stress: 31000 psi, Static Loading, Ultimate Strength = 80000 psi Material: Polystyrene, Von Mises Stress: 42000 psi, Static Loading, Ultimate Strength = 7500 psi Material: Aluminum, Von Mises Stress: 62000 psi, Repeated Loading, Ultimate Strength = 30000 psi Please clearly show all calculations and reasoning in your computation.arrow_forward
- The adjacent sketch indicates a brass wire which is exactly 12.00 m long and a steel wire which is 12.01 m long. Each wire has a cross-sectional area of 150 mm2 . What load does each wire carry if E steel = 200,000 MPa & E brass = 110,000 MPa? (Hint: no load on steel wire until brass wire stretches by 10mm, then ratio of stresses in each wire is same as ratio of E varrow_forwardA beam has a cross section show below. If the stress at point P is 30Kpa , calculate the value for the shear force V. can you please show details? especially how to calculate the moment of inertia. I got a first response but I got confuse how the person use the parameters to calculate INERTIAarrow_forwardThe beam shown in figure carries a concentrated load of w and total u.d.l load of 8 w , determine the maximum safe value w that will not exceed allowable stresses Segma 1 = 18 Mpa , Segma 2 = 64 Mpa tau = 12 Mpaarrow_forward
- Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage LearningSolid Waste EngineeringCivil EngineeringISBN:9781305635203Author:Worrell, William A.Publisher:Cengage Learning,