Materials for Civil and Construction Engineers (4th Edition)
4th Edition
ISBN: 9780134320533
Author: Michael S. Mamlouk, John P. Zaniewski
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 1, Problem 1.5QP
A cylinder with a 6.0 in. diameter and 12.0 in. length is put under a compressive load of 150 kips. The modulus of elasticity for this specimen is 8.000 ksi and Poisson’s ratio is 0.35. Calculate the final length and the final diameter of this specimen under this load assuming that the material remains within the linear elastic region.
Expert Solution & Answer
Learn your wayIncludes step-by-step video
schedule05:41
Students have asked these similar questions
A cylinder with a 6.0 in. diameter and 12.0 in. long is put under a compressive load of 150,000 lbs. The modulus of elasticity for this specimen is 8,000,000 psi. and Poisson’s ratio is 0.35. Calculate the final length and the final diameter of this specimen under this load assuming that the material remains within the linear elastic region.
A cylinder with a 6.0 in. diameter and 12.0 in. length is put under a compressive load of 150 kips. The modulus of elasticity for this specimen is 8,000 ksi and Poisson’s ratio is 0.35. Calculate the final length and the final diameter of this specimen under this load assuming that the material remains within the linear elastic region.
A metal rod with 0.5 in. diameter and 12.0 in. length is put under a compressive load of
150 kips. The modulus of elasticity for this specimen is 8,000 ksi and Poisson’s ratio is 0.35.
Calculate the final length and the final diameter of this specimen under this load assuming that
the material remains within the linear elastic region
Chapter 1 Solutions
Materials for Civil and Construction Engineers (4th Edition)
Ch. 1 - State three examples of a static load application...Ch. 1 - A material has the stressstrain behavior shown in...Ch. 1 - A tensile load of 50.000 lb is applied to a metal...Ch. 1 - A tensile load of 190 kN is applied to a round...Ch. 1 - A cylinder with a 6.0 in. diameter and 12.0 in....Ch. 1 - A metal rod with 0.5 inch diameter is subjected to...Ch. 1 - A rectangular block of aluminum 30 mm 60 mm 90...Ch. 1 - A plastic cube with a 4 in. 4 in. 4 in. is...Ch. 1 - A material has a stressstrain relationship that...Ch. 1 - On a graph, show the stressstrain relationship...
Ch. 1 - The rectangular block shown in Figure P1.11 is...Ch. 1 - The rectangular metal block shown in Figure P1.11...Ch. 1 - A cylindrical rod with a length of 380 mm and a...Ch. 1 - A cylindrical rod with a radius of 0.3 in. and a...Ch. 1 - A cylindrical rod with a diameter of 15.24 mm and...Ch. 1 - The stressstrain relationship shown in Figure...Ch. 1 - A tension test performed on a metal specimen to...Ch. 1 - An alloy has a yield strength of 41 ksi, a tensile...Ch. 1 - Prob. 1.21QPCh. 1 - Figure P1.22 shows (i) elasticperfectly plastic...Ch. 1 - An elastoplastic material with strain hardening...Ch. 1 - A brace alloy rod having a cross sectional area of...Ch. 1 - A brass alloy rod having a cross sectional area of...Ch. 1 - A copper rod with a diameter of 19 mm, modulus of...Ch. 1 - A copper rod with a diameter of 0.5 in., modulus...Ch. 1 - Define the following material behavior and provide...Ch. 1 - An asphalt concrete cylindrical specimen with a...Ch. 1 - What are the differences between modulus of...Ch. 1 - Prob. 1.33QPCh. 1 - A metal rod having a diameter of 10 mm is...Ch. 1 - What is the factor of safety? On what basis is its...Ch. 1 - Prob. 1.36QPCh. 1 - Prob. 1.37QPCh. 1 - A steel rod, which is free to move, has a length...Ch. 1 - In Problem 1.38, if the rod is snugly fitted...Ch. 1 - A 4-m-long steel plate with a rectangular cross...Ch. 1 - Estimate the tensile strength required to prevent...Ch. 1 - Prob. 1.42QPCh. 1 - Briefly discuss the variability of construction...Ch. 1 - In order to evaluate the properties of a material,...Ch. 1 - A contractor claims that the mean compressive...Ch. 1 - A contractor claims that the mean compressive...Ch. 1 - Prob. 1.47QPCh. 1 - Prob. 1.48QPCh. 1 - Prob. 1.49QPCh. 1 - Briefly discuss the concept behind each of the...Ch. 1 - Referring to the dial gauge shown in Figure P1.51,...Ch. 1 - Repeat Problem 1.51 using the dial gauge shown in...Ch. 1 - Measurements should be reported to the nearest...Ch. 1 - During calibration of an LVDT, the data shown in...Ch. 1 - During calibration of an LVDT, the data shown in...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
List three sources of epistemic uncertainty associated with determining the soil strength at a given site and d...
Foundation Design: Principles and Practices (3rd Edition)
10.5" Balance the angles in Problem 9.22 El. Compute the preliminary azimuths for each
course.
Elementary Surveying (14th Edition)
(a) The influence lines for the moment at C.
Structural Analysis (10th Edition)
10.5" Balance the angles in Problem 9.22 El. Compute the preliminary azimuths for each
course.
Elementary Surveying: An Introduction To Geomatics (15th Edition)
Resolve the component force F1 into its x and y components, F1x and F1y . Resolve the component force F2 into i...
Engineering Mechanics: Statics & Dynamics (14th Edition)
Determine the moment of inertia of the beams cross-sectional area about the y axis.
Engineering Mechanics: Statics
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.arrow_forwardThe data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.arrow_forwardA tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.arrow_forward
- A cylinder with a 150 mm diameter and 300mm length is put under a compressive load of 665 kips. The modulus of elasticity for this specimen is 55 GPa and Poisson’s ratio is 0.35. Calculate the final length and the final diameter of this specimen under this load assuming that the material remains within the linear elastic region.arrow_forwardA stainless-steel rod 16mm in diameter and 300mm long is put under a tensile load of 250 kN. Assuming that the modulus of elasticity for this specimen is 250,000 MPa and the final diameter is 15.96 mm. Calculate the final length, in mm, and the Poisson’s ratio of this specimen under this load assuming that the material remains within the linear elastic region.arrow_forwardIn a simple tensile test using a cylindrical test specimen (Dia.=10mm), the applied force was 120 kN and the extension was 2%. Find the modulus of elasticity of that specimen. If the standard modulus of elasticity is 200 GPa, is this material accepted or not? and why?arrow_forward
- To stretch a 200 mm long tensile test specimen (a) of steel elastically by 0.08 mm. How many loads do I need to apply? (b) What is the maximum length of this sample without plastic deformation? How long can it be extended? (The modulus of elasticity of steel is 210 GPa, yield strength 580 MPa, tensile strength 920 MPa specified as.arrow_forwardA cylinder with a 150 mm diameter and 300 mm length is put under a com-pressive load of 665 kN. The modulus of elasticity for this specimen is 55 GPa and Poisson’s ratio is 0.35. Calculate the final length and the final diameter ofthis specimen under this load assuming that the material remains within thelinear elastic region.arrow_forwardConsider a bar with a rectangular cross-section area with a thickness of t = 0.5 in. and height of h = 3.5 in. When force P = 19 kips is applied to the bar, the strain gages attached to the surface of the bar reads εx = 740 µε along the direction of the force and εy = -170 µε in the perpendicular direction. Determine Poisson's ratio for this specimen? Determine the modulus of elasticity for this specimen?in Ksiarrow_forward
- A tension test is being conducted on a steel-rod specimen with a gauge length of L0=2 in and initial diameter of d0=0.5 in. Data were collected to form the conventional stress-strain diagram as shown. From the diagram, f = 74.0 ksi, e = 104.0 ksi , g = 85.0 ksi , and h = 0.15 in/in. Assuming that the strain remains constant throughout the region between the gauge points, determine the nominal strain ε experienced by the rod if it is elongated to L = 2.7 in . Assuming that the stress is constant over the cross-sectional area and if the tension force used is P = 11.0 kips, find the nominal stress experienced by the rod. Determine the force P needed to reach the ultimate stress in the steel-rod specimen.arrow_forwardA tensile test was performed on a metal specimen with a diameter of 1⁄2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The data were plotted on a load-displacement graph, P vs. ∆L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P y∆L 5 1392 kips yin. What is the modulus of elasticity?arrow_forwarda liquid compressed in a cylinder has a volume of 1500cm³ at 1 mn/m² and a volume of 1495 cm³ at 2mn/m² . determine the bulk modulus of elasticity. answer must be correct.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage LearningSteel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning
Steel Design (Activate Learning with these NEW ti...
Civil Engineering
ISBN:9781337094740
Author:Segui, William T.
Publisher:Cengage Learning
Material Properties 101; Author: Real Engineering;https://www.youtube.com/watch?v=BHZALtqAjeM;License: Standard YouTube License, CC-BY