The steel framework shown below is used to support a 4-inch thick reinforced concrete slab andcarries a uniform Live Load of 400 lb/ft2. The Density of Reinforced Concrete=150 lb/ft³.Sketch the loading that acts along members BE and FED.CA-b-BF02 PROB_001-002Carte CakeEaGiven: a=6 ft, b=12 ft,0Da

Given data,reinforced concrete slab thickness=4inUniform live load=400lb/ft2Density of reinforcement…

The steel framework shown below is used to support a 4-inch thick reinforced concrete slab and carries a uniform Live Load of 400 lb/ft². The Density of Reinforced Concrete=150 lb/ft³. Sketch the loading that acts along members BE and FED. Given: a=6 ft, b=12 ft, C A -b B F 02 PROB_001-002 Ce e E D

The steel framework shown below is used to support a 4-inch thick reinforced concrete slab and carries a uniform Live Load of 400 lb/ft². The Density of Reinforced Concrete=150 lb/ft³. Sketch the loading that acts along members BE and FED. Given: a=6 ft, b=12 ft, C A -b B F 02 PROB_001-002 Ce e E D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Asiacell|Asiacel K/s Asiacell For simply supported beam with rectangular cross section shown, determine the values and location of the maximum tensile and compressive bending * stresses 1000 lb 400 lb/ft 6 in DV 8 in 10 ft RA Rp
1. See figure below and solve for the maximum value of torque the composite shaft can accommodate given a maximum shear stress of 8ksi in bronze and 12 ksi for the steel. Assume bronze has G = 6 × 103 ksi, and for steel, G = 12 × 103 ksi. %3| L C2" 3" Hollow Bronze Steel Core D = 3 in, d = 2 in D = 2 in
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
1. See figure below and solve for the maximum value of torque the composite shaft can accommodate given a maximum shear stress of 8ksi in bronze and 12 ksi for the steel. Assume bronze has G = 6 x 10° ksi, and for steel, G = 12 x 10% ksi. T L 2" |3" Steel Core D = 2 in Hollow Bronze D = 3 in, d = 2 in
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
A simply supported beam, circular in cross section, of span L supports a point load W at mid span. The length of elastic-plastic zone at the plastic hinge will be A 0.33 L B 0.41 L C 0.50 L D 0.58 L
2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Specify whether tension or compression. Bronze Aluminum Steel A =400 mm2 A= 600 mm2 A = 300 mm2 2P ЗР 4P P -3 m 5 m 4 m Stress in Bronze (MPa) %D Stress in Aluminum (MPa) %3D Stress in Steel (MPa)
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
Two T-shape sections are welded together to create a composite l-beam section as shown below. Determine the safely uniform load w (kN/m) that the beam can carry throughout its entire span. 270mm 30mm 20mm 160mm Welded Joint 130mm 30mm 135mm Beam Length = 4 m Consider the following stresses: fb(T) 3 125 МPа fb(C) = 130 MPa x at the welded joint = 20 MPa Find: 1. The Neutral Axis from the base 2. moment of inertia with respect to the horizontal centroidal axis 3. Q at the welded joint 4. Considering the maximum flexural stress in tension, WNAX is equal to KN/m. 5. Considering the maximum flexural stress in compression, WMAX, is equal to 6. Considering the stress at the welded joint, wMex is equal to kN/m.
A cantilever beam with a ‘T’ shaped cross-section is loaded with a distributed load as shown below.The intensity of the distributed load is 100N/mm. b = 6.25mm and c=6.25mm.Parameter Description Value UnitsL - Beam length 250 mma - Width of the flange 80 mmd - Height of the web 75 mmσ - Yield stress 250 MPaYou are tasked with ensuring the beam can withstand the applied loading. To do this you must:a) Calculate the centroid for the given cross-section. Your value of ?ത should be measured fromthe bottom of the section. Determine an expression for Q (statical moment of area) for thegiven shape. The expression(s) for Q should be in terms of the variable, y, measured from thebottom of the section. b) Create a graph of the shear and bending stresses at the fixed support (B) over the crosssection. The stresses should be plotted as a function of y, measured from the bottom of thesection.
Direct Stress Bronze Aluminum Steel A = 0.75 in.2 A = 1.0 in.? A = 0.5 in.? 3P 2F P 4P- -3 ft→ 5 ft 4 ft- 2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. Find the largest safe value of P if the working stresses are 120 MPa for steel, 68 MPa for aluminum, and 110 MPa for bronze.
Axial loads are applied to the compound rods that composed of an aluminum segment rigidlyconnected between steel and bronze segments. If P = 25 kN, determine the following: a. Stress in the bronze segment. b. Stress in the aluminum segment. c. Stress in the steel segment.