For the built-up shape shown, determine: (a) the elastic section modulus and the yield moment (b) the plastic section modulus and the plastic moment Mp. Bending is about the x-axis, and the steel is A572 Grade 50. Fy = 345 MPa

For the built-up shape shown, determine: (a) the elastic section modulus and the yield moment (b) the plastic section modulus and the plastic moment Mp. Bending is about the x-axis, and the steel is A572 Grade 50. Fy = 345 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (ay) MPa, and for the bronze (ay)or 520 MPa, determine the magnitude of the largest elastic load P 640 that can be applied to the assembly. E 200 GPa, Ebr= 100 GPa. 10 mm 20 mm Figure 2: Steel Bolt
Need correctly in neat and clean handwritten solution explaining every steps
determine: (a) the elastic section modulus and the yield moment. (b) the plastic section modulus and the plastic moment Mp. Bending is about the x-axis, and the steel is A572 Grade 50. Fy = 345 MPa Subject: Civil Engineering Steel Design
As shown in the figure below, a bronze bar is affixed between a steel bar and an aluminum bar. Axial loads are applied at the positions indicated. If the largest value of P that will not exceed an overall deformation of 4.0 mm, or the following stresses: 150 MPa in the steel, 130 MPa in the bronze, and 90 MPa in the aluminum, determine the stress in the bronze. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. (The correct answer is 71.36 MPa. Can you show the solution? Thank you!)
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 30-in.-long bronze [E = 15900 ksi a = 9.4x 10-6/°F] bar with a cross-sectional area of 1.00 in.?. Bar (2) is a 48-in-long aluminum alloy [E = 9200 ksi, a = 12.6 x 10-6/°F] bar with a cross-sectional area of 2.50 in.?. Both bars are unstressed before the load Pis applied. Assume L4=30 in., L2=48 in., a-32 in., b=44 in., and c=14 in. If a concentrated load of P = 29 kips is applied to the rigid bar at Dand the temperature is decreased by 120°F, determine: (a) the normal stresses in bars (1) and (2). (b) the normal strains in bars (1) and (2). (c) the deflection of the rigid bar at point D. (2) L2 A B D L1 (1) b
The critical bending compressive stress in the extreme fibre of a structural steel section is 1000 MPa. It is given that the yield strength of the steel is 250 MPa, width of flange is 250 mm and thickness of flange is 15 mm. As per the provisions of IS: 800 -2007, the non-dimensional slenderness ratio of the steel cross-section is (a) 0.25 (c) 2.00 (b) 0.75 (d) 0.50
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress (in Mpa) in the bronze given that P= 188 kN? Express your answer in four decimal places.
The assembly consists of two red brass C83400 copper rods AB and CD of diameter 30 mm, a stainless 304 steel alloy rod EF of diameter 40 mm, and a rigid cap G. The supports at A, C and F are rigid. Modul of elasticy for the copper is Ecopper = 101 GPa. Modul of elasticity for the steel is Esteel = 193 GPa. (Figure 1) Figure ▼ Part A σAB = Submit Part B Value Submit μÀ Request Answer Part C LO OCD = Value Determine the average normal stress developed in the rod AB. Express your answer to hree significant figures and include the appropriate units. μA Request Answer EF = Units Units A μÃ -300 mm- Value C 30 mm Determine the average normal stress developed in the rod CD. Express your answer to three significant figures and include the appropriate units. Submit Request Answer 30 mm ? B D G ? E 450 mm 40 kN 40 kN 40 mm Determine the average normal stress developed in the rod EF. Express your answer to three significant figures and include the appropriate units. Units F ? < 1 of 1
What is another term for bend? (A) flex B compress fracture D) twist E stretch