A reinforced concrete beam that is 375 mm wide and 500mm deep must resist a service live load moment of 250 kN-m and a service dead load moment of 150 kN-m. Use f'c-21 MPa ar fy=415 MPa. The effective concrete cover is 65mm (to the centroid of reinforcements). 1. Determine the area of compression steel reinforcement (If required. Answer O if not) in mm 2. Determine the minimum number of 25 mm diameter bars to be provided to satisfy the demand ultimate moment

A reinforced concrete beam that is 375 mm wide and 500mm deep must resist a service live load moment of 250 kN-m and a service dead load moment of 150 kN-m. Use f'c-21 MPa ar fy=415 MPa. The effective concrete cover is 65mm (to the centroid of reinforcements). 1. Determine the area of compression steel reinforcement (If required. Answer O if not) in mm 2. Determine the minimum number of 25 mm diameter bars to be provided to satisfy the demand ultimate moment

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design the slab reinforcement if the maximum positive moment is Mup=wul2/11 . and the maximum negative moment is Mup=wul2/19. Include the design for S&T bar. Given: length = 6m span = 2m Wu= 8.572 kPa Slab thickness = 150 mm f'c = 28 MPa fy= 219 MPa main bar = 10 mm s&t bar = 8mm
Determine the required tension steel area of the T beam with given properties below. Width of flange bf = 500 mm Width of web bw = 340mm Thickness of flange tf = 140 mm Effective depth d = 350 mm Effective concrete covering d' = 75 mm Compressive strength of concrete fc' = 34.5 MPa Yield stress of steel bar fy = 375 MPa Mu = 415 kN-m As = mm2
Q-A pre-tensioned concrete member of section 200 mm x 250 mm contains tendons of area 500 mm² at centre of gravity of the section. The prestress in the tendons is 1000 N/mm². Assuming modular ratio as 10, find the stress (N/mm2) in concrete.
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars, Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MP.. 640 mm 800 mm 6 #32 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
The concrete post is reinforced axially with four symmetrically placed steel bars, each of cross-sectional area 900 mm2. Compute the stress in each material when the 1000-kN axial load is applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Compatibiltiy Equation . Ust Bearing |1000 kN plate Steel- Concrete 300 mm 300 mm Section a-a
A spiral column with the diameter of 500 mm has the effective height of lo-4.0 m. The axial compressive strength of the concrete is f. = 14.3 N/ mm. The longitudinal steel bars are 6 22 with the yield strength of fy = 360 N/mm. The spirals are d 10@50 with the yield strength of fy = 270 N/ mm. If the concrete cover is 30 mm thick, determine the ultimate compressive capacity of the column.
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars. Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MPA. 640 mm 800 mm 6 #32 C 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
A rectangular beam with a width of (9536/1150)-in,and effective depth of (9536/900)in is Reinforced with a single high strength steel bar that has a cross- sectional area of 0.42 in2.The bar has a normal tensile strength of 145 ksi, linear stress-strain curve to failure, and a strain at failure of 1.8 percent. The concrete strength fc= 6000 psi. Calculate the nominal flexural strength of the section.
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.2 m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-∅25 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f'c = 21 Pa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars Determine the limiting tensile steel ratio for a tension controlled condition in positive or negative bending with the given material strengths.
A rectangular beam has a width of 285 mm and an effective depth of 520mm. It is reinforced with 4 – 36 mm ø bars having fy = 430 MPa. If he compressivestrength of the concrete is 28MPa, find the following a. Location of the neutral axis from the top of the beam.b. Stress of the steel.c. Ultimate capacity of the beam?
38 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the nominal moment capacity in kN∙m of the beam in positive bending. Write the answer in 2 decimal places only.