2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Specify whether tension or compression. Bronze Aluminum Steel A=400 mm2 A=600 mm2 A = 300 mm2 2P ЗР 4P -3 m + -5m 4 m-

2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Specify whether tension or compression. Bronze Aluminum Steel A=400 mm2 A=600 mm2 A = 300 mm2 2P ЗР 4P -3 m + -5m 4 m-

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter14: Material Selection

Section: Chapter Questions

Problem 3ETSQ

See similar textbooks

Similar questions

The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. %3D Steel E200 GPa A-600mm L1 m 2.0 m 0.6 m 1.5 m Pa20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the ratio of the deformation of steel to deformation of aluminum?
Situation No. 2 A bronze bar is fastened between a steel bar and an aluminum bar as shown below. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Bronze Steel A = 480 mm? Aluminum A = 650 mm A = 320 mm 3P 4P 2P 1.0 m 2.0 m 1.5 m
Problem 2: A bronze bar is fastened between a steel bar and an aluminum bar as shown. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel Bronze 480 mm² 650 mm² 3P 1.0 m 4P 2.0 m Aluminum 320 mm² 1.5 m 2P
The modulus of elasticity of mild steel is equal to .. .? .... .. a. 2 x 10ʻN/m? a. 2 x 10'N/m 2 b. 2 x 10° N/m 4 c. 2 x 10 N/mm 5 d. 2 x 10 N/mm Check
5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in Figure 5. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m FIGURE 5 Aluminum A = 320 mm² 1.5 m 2P
An aluminum tube is fastened between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. For Bronze: Allowable stress = 120 MPa, EB = 83,000 MPa For Aluminum: Allowable stress = 120 Mpa, EA = 70,000 MPa For Steel: Allowable stress = 120 MPa, Es = 200,000 MPa Assume that the assembly is suitably braced to prevent buckling. Maximum overall deformation should not exceed 2mm. a) Give the value of the force acting on the bronze so as not to exceed allowable stresses and deformation. b) Give the value of the force acting on the aluminum so as not to exceed its allowable stresses and deformation. c) Give the value of the force acting on the steel so as not to exceed its allowable stresses and deformation.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
A 8 mm radius Steel is subjected to tensile test. Determine its yield and and ultimate load it can carry in kN when the steel grade is 60 and 40. Determine also its elongation using the stresses if the modulus of elasticity of steel 218 GPa. Determine also the weight if the length is 8 m and 18 m.Hint: There are two 8 mm radius Steel.
As shown in the figure below, a bronze bar is affixed between a steel bar and an aluminum bar. Axial loads are applied at the positions indicated. If the largest value of P that will not exceed an overall deformation of 4.0 mm, or the following stresses: 150 MPa in the steel, 130 MPa in the bronze, and 90 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. determine the stress in the bronze, steel, and aluminum
Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 15 degrees Celsius and the stress on the bars is zero. Eventually, the temperature increased to 25 degrees Celsius. Determine the total deformation on the steel. Steel Brass Copper Est = 200 GPa Ebr = 100 GPa Ecu = 120 GPa %3D ast = 12(10-6)/°C abr = 21(10¬6)/°C acu = 17(10-)/°C %3D Acu = 515 mm² |Ast = 200 mm? Abr = 450 mm² %3D 300 mm- 200 mm 100 mm O -0.0058mm O 0.0165mm O -0.0165mm O 0.0058mm
As shown in the figure below, a bronze bar is affixed between a steel bar and an aluminum bar. Axial loads are applied at the positions indicated. If the largest value of P that will not exceed an overall deformation of 4.0 mm, or the following stresses: 150 MPa in the steel, 130 MPa in the bronze, and 90 MPa in the aluminum, determine the stress in the bronze. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. (The correct answer is 71.36 MPa. Can you show the solution? Thank you!)
A bronze bar is fastened between a steel bar and an aluminum bar as shown in the figure. Axial loads are applied at the positions indicated. The allowable overall deformation is not to exceed 1.2 mm. Assume that the 2P Aluminum L- 1.5 m A= 550 mm E= 70 GPa Steel Bronze L= 2.0 m L= 1.0 m A= 600 mm A= 650 mm E= 200 GPa E= 83 GPa assembly is suitably braced to prevent buckling. Find the maximum permissible value of P.