The rod BD is made of material with G1= 124 GPa has adiameter 34 mm is bonded to the tube CA at point B, thetube made of material with G2=211 GPa has an outerdiameter 73 mm and wall thickness of 10 mm. If T1=579N.m and T2=1042 N.m, answer the following questions:T2 N-m0.4 m0.1 m0.3 mTi N-mThe maximum shear stress of the tube CA isYour answerThe maximum shear stress of the assemblyisYour answerThe angle of twist between D and B isYour answerThe angle of twist between C and A isYour answer

Given: Rod BD: G1=124 GPad=34 mm Tube CA: G2=211 GPaD0=73 mmt=10 mmT1=-579 N.m (counter clockwise…

The rod BD is made of material with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at point B, the tube made of material with G2=211 GPa has an outer diameter 73 mm and wall thickness of 10 mm. If T1=579 N.m and T2-1042 N.m, answer the following questions: B T2 N-m 0.4 m 0.1 m 0.3 m T1 N-m

The rod BD is made of material with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at point B, the tube made of material with G2=211 GPa has an outer diameter 73 mm and wall thickness of 10 mm. If T1=579 N.m and T2-1042 N.m, answer the following questions: B T2 N-m 0.4 m 0.1 m 0.3 m T1 N-m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The cross-sectional area of the bar is 5 cm². Use E = 70 GPa for aluminum, and E = 200 GPa for steel. L. Aluminum Steel Aluminum 80 kN 20 kN - 30 kN + 70 kN A D B - 3 m - - 4 m · 5 m
Draw the free body diagrams for each part in the figures below:
T2=400°F
h1= 1.05 m h2=0.25 m w=0.50 m
The collar C is fixed to rod AB using a glued bond that allows a maximum force of 405 N parallel to the axis of the rod. The collar has weight W acting in the negative z direction. Determine the weight W in N of the collar that will cause the glued bond to break as shown in figure.
2.5 m 5 m 7.5 m 5 m K 10 m 5 m K K K 20 m Obtain the center of stiffness
Q;Determine the stiffness and elasticity matrices of the system below:
A8-mm-diameter wire (E = 120 GPa) supports a tension load of 1.5 kN. If the total elongation of the wire must not exceed 14 mm, determine the maximum allowable length L of the wire. 1,500.00 N m 14.21 m 15.48 m 12.67 O m 10.86 m 14.07 O
ı need solution
Determine the vertical displacement of point C in inches by using the method of virtual work. A is a fixed support. o E = 29000 ksi, o 1 = 120 in4 C bft 3 ft 3 k/ft A B 10 ft
The stepped rod is made up of two different materials A and B of lengths 80 cm and 1.2 m respectively. The diameters of materials B and A are 2.5 and 3.5 cm respectively. The modulus of elasticity of materials A and B are 250 and 150 GPa respectively. The elongation of the rod is the same for both the materials. A total tensile load of 40 kN is applied to both the materials A and B together. Calculate the load in each material.
ll ? The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at point B, the tube made of material with G2=230o GPa has an outer diameter 37 mm and wall thickness of 7 mm. li T1=803 N.m and T2=1445 N.m, answer the following questions: B T2 Nm 04 m 0.1 m 0.3 m TI N-m The polar moment of inertia of the rod BD is Your answer The polar moment of inertia of the tube CA is