The rigid bars AB and CD are supported by pins at A and D. The vertical rods are made of aluminium and bronze as shown. Determine the vertical displacement at Point B when the force P is equal to SN kips is applied. Neglect the weight of the bars. Aluminum E=10x10 psi L=3ft A= 0.75 in? в Bronze E=12x10 psi L=4ft 2 ft 3 ft A= 0.25 in? D 2ft 2ft

The rigid bars AB and CD are supported by pins at A and D. The vertical rods are made of aluminium and bronze as shown. Determine the vertical displacement at Point B when the force P is equal to SN kips is applied. Neglect the weight of the bars. Aluminum E=10x10 psi L=3ft A= 0.75 in? в Bronze E=12x10 psi L=4ft 2 ft 3 ft A= 0.25 in? D 2ft 2ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rigid bar AB and CD are supported by pins at A and D. the vertical rods are made of aluminum and bronze. Determine the vertical displacement of the point where the force P= 10 kips is applied. Neglect the weight of the members.
2m 9. The rod AB rests on a horizantal surface at A and against slipping suface at B if Ms =0-25 at A&B. Find the minimum distance a for equilibriam, negledt the weight ( Ans a-l-6lm) a 60N • peu m7 jo
Neglect the thickness of the bar. Take ua=ub=u suppose that b= 1 ft
3. At temperature T₁, the two rigidly connected rods just fit the rigid supports. If both sections are identical except for the diameter, prove that the following equations are true when temperature rises to T₂. a. F= b. OAB C. OBC A x(T₂-T₁)лd²E 20 x(T₂-T₁)E 5 9x(T₂-T₁)E 5 -1/2- d B 1/12- d C
The 20 mm diameter steel shaft AB is attached into the rigid wall at B and supported by a smooth bearing at A. The lever AC is welded to the end of the shaft. If the downward force P will produce a 50 mm vertical displacement at the free end of lever AC, determine the force P if G = 83 GPa.
Q2/ The 10-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an inner diameter of 15 mm and an outer diameter of 25 mm. The original lengths of the bolt and sleeve are 80 mm and 50 mm, respectively. If after the nut on the bolt is tightened the tension in the bolt is 10 kN, determine the change in dimension of the cross-section of the bolt and the sleeve. Assume the material at A is rigid. Ea = 70 GPa, Emg = 45 GPa, Ga = 26 GPa, Gmg = 17 GPa. 50 mm 30 mm
Q2/ The 10-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an inner diameter of 15 mm and an outer diameter of 25 mm. The original lengths of the bolt and sleeve are 80 mm and 50 mm, respectively. If after the nut on the bolt is tightened the tension in the bolt is 10 kN, determine the change in dimension of the cross-section of the bolt and the sleeve. Assume the material at A is rigid. E = 70 GPa, Emg = 45 GPa, Ga 26 GPa, Gmg= 17 GPa. 50 mm 30 mm
The bar ABC is supported by a pin at A and a steel wire at B. Determine the magnitudeof force Pinlbif the elongation of the wire is 0.059 in. The cross-sectional area of the wire is 0.0039 inandthemodulus of elasticity of steel is 29001 ksi,X=3.86 ft, Y = 6.78 ft, and L = 5.6 ft. Express the final answer to four decimal places. ... B Y
Y L 6 ft 100kg 6 ft 6 ft 6 ft Apply a load of 100 kg to the center of the design. Considering it as a two- dimensional problem, determine the force acting on member.
The uniform 300-lb bar AB carries a 500-lb vertical force at A. The bar is supported by a pin at B and the 0:5-in. diameter cable CD. Find the stress in the cable. 4 ft A 3 ft 3 ft B. 500 Ib
Prior to the application of the P = 120 kip load, the gap between C and the rigid wall at D was as depicted as below. Determine the support reaction at D (in kip) after force P has been applied. The assembly is made of solid cylinders: AB is Stainless 304 steel alloy, and BC is 6061-T6 aluminum alloy.
Question 1: Given that Tuitow = 50 MPa for the rod AB and tattow = 25 MPa for the rod BC. If T=1250 N.m, find the required radius for both rods. Ahmtmum AB = BC =