The compound bar carries axial loads as shown. Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 inch and the working stresses listed in the table are not to be exceeded.

Q: m A solid sphere of mass 3m and radius 2R has a rope tied around it. The free end is wrapped around…

A: Given: Mass of sphere = 3m Radius of sphere = 2R Mass of pulley = m Radius of pulley = R Mass of…

Q: An 18 kg Block A on an incline (p =30 degrees), is pulled by a 130-N force P. Friction in the pulley…

A: To be explained :- Free body diagram

Q: A member in tension in a machine frame is subjected to a continuous load of 5.00 kN. Its length is…

A: Given data  Length of member = 750 mm Load = 5.00 kN Outer diameter = 17 mm Inner diameter = 12 mm…

Q: 3.51 The 0.61 x 1.00-m lid ABCD of a storage bin is hinged along side AB and is held open by looping…

A: Given data: A=0.61×1.00 mm2T=66 N Need to determine the moment about each coordinate axes of the…

Q: The shaft shown in the figure is machined from AISI 1030 CD steel. The shaft rotates at a constant…

A:

Q: An object is sliding down a cord, as shown. Write a program which takes the initial lengths a, b,…

A: Given: To find: Code to give output as velocity and acceleration in cylindrical coordinates

Q: find of center mass of the racecar (X, Y, Z ) ! X is formand and aft relative to the middle of the…

A:

Q: Steam enters a turbine operating at steady state at 700°F and 450 lbf/in² and leaves as a saturated…

A:

Q: annotate on this screw pump the important parts ...... bearing , screw Rotor , others .........…

A: To find: To Label the par of the given screw pump.

Q: Given the diagram below, determine the magnitude of the moment (in N-m) caused by Force X about the…

A:

Q: . The container in Fig. 4.19 is initially evacuated. Then the valve is opened, and atmospheric air…

A: Write the given data. T1=20 °CV1=10 m3P1=1 atm=101235 PaR=287 J/kgKW=13 kJ

Q: Which is the most accurate description of one of the system's processes? A Fluid moves from the…

A: A system process is defined as the entity which represents the basic unit of work implemented on the…

Q: 300 lb./ft. 9 ft. 600 lb./ft. 5 ft. 200 lb./ft. B 7 ft. 1000 lb.

A:

Q: 1.) Glass tends to break under high temperatures due to thermal shock which is caused by a high…

A: Given data  Tbreak = 190°C Heat transfer rate = 1 kw Area = 1 m2 Thickness = 5 cm  Thermal…

Q: Chip 1 has 3 Ring Oscilltors on it. Calculate the Calibrated Ring Oscillator value for Chip 1 and…

A: Given: To find: calculate the Calibrated RO_x

Q: Normal force = N[0.6j+0.8k] mass of object in point A: 81 kg 1.5m 1.5m X B 2m 2m mass: 81 kg 5m 5m Y…

A:

Q: As shown in the figure below, a reversible power cycle receives energy QH by heat transfer from a…

A: Answer (a): Calculate the thermal efficiency. ηTh=1-TCTH      =1-4001600ηTh=0.75ηTh=75%

Q: and normal acceleration varying with time as wat, where a is constant. Find the time dependence of…

A:

Q: An isentropic pump, processes 3.7 kg of Gas using 90 kW of power. If the process is changed to…

A:

Q: Q3. The built-up wooden beam shown is subjected to a vertical shear of 5 kN. The longitudinal…

A:

Q: Steams flow steadily through an adiabatic turbine. The inlet conditions of the steam are 10 MPa, 450…

A:

Q: Problem 3: A 0.625 in. thick rectangular alloy bar is subjected to a tensile load P by pins at A and…

A:

Q: A 16 lbs cylinder rests in the trough shown. Assume that the contact surfaces are smooth…

A:

Q: The exposure rate to the fingers of a technologist holding a generator elution vial is 5.3 R/hr…

A:

Q: An ordinary egg can be approximated as a 5.5-cm-diameter sphere whose thermal conductivity of…

A:

Q: As shown in the figure below, two reversible cycles arranged in series each produce the same net…

A:

Q: A wood fire with a temperature of 1110F is at the other side of a 10 square ft wall that has a…

A:

Q: Consider the picture below. Find the resultant force and the location of the resultant force. T 100…

A:

Q: 0 Three forces act on point : A = 60 N at 135°, B= 50 N at -45° and, C=75 Nat 60°. Estimate the…

A: given; A=60NB=50NC=75Nresultant force(R)=?direction(θ)=?

Q: A reversible power cycle operating as in the figure receives energy QH by heat transfer from a hot…

A:

Q: can you help me solve this question about equlibrium of a particle using the polygon method? four…

A: Given data:-four pieces of string are tied to a massless ring To find:- equilibrium of a particle…

Q: 22-24. The large and small pistons in a hydraulic lift have an area of 360 cm² and 45 cm²,…

A:

Q: Find the mass density (p). Given: weight density (y)= 56.061 lb/ft³ V= 0.033 ft³ Do not use the…

A:

Q: 1. Locate the centroid and compute for the moment of inertia of the following section wrt X-X. Use…

A: Given data as per the question Thickness of web =13 mm

Q: A system executes a power cycle while receiving 1000 Btu by heat transfer at a temperature of 900°R…

A:

Q: 8.0 30% 30% 0.2 m----0.2 m----0.2 m D Draw the free-body diagram needed to determine the tension in…

A: Given: Let us consider the given image, To find: Tension in the cords and the reactions at A and C.

Q: At steady state, a new power cycle is claimed by its inventor to develop net power at a rate of (a)…

A:

Q: A 4-cm-OD, 3-cm-ID, circular shaft supports a 200 N load and is supported at two points, which are…

A:

Q: D с 55 50° 75° B A Solution Determine the magnitude and direction of force D required for…

A:

Q: Given the diagram below, determine the following: 3m 2m m Im Fim1.5m. -1.5m 1.5m 5m 3 kN 3 m 4 kN 2m…

A:

Q: Refrigerant 134a at p₁ = 30 lb/in², T₁ = 40°F enters a compressor operating at steady state with a…

A:

Q: A symmetrical I-beam is subject to a shear force of 35379N acting along its entire length. The beam…

A: Given data as per the question shear force =35379 N Width of flange =21mm The thickness of flange…

Q: Blowers are used in wastewater treatment plants to assist microorganisms in degrading pollutants.…

A: Given data as per the question The radius of the blower at the inlet =15 cm blade width =6.1 cm…

Q: 3.149 A small boat hangs from two davits, one of which is shown in the figure. The tension in line…

A:

Q: 2. Compute the resultant of the three forces as shown. Locate its intersection with the x and y…

A:

Q: A cantilever beam with a uniform flexural rigidity (EI=200 * 10^6 N.m2) is concentrated force at its…

A:

Q: Water contained in a closed, rigid tank, initially at 100 lb/in², 800°F, is cooled to a final state…

A:

Q: (10) Calculate the ratio of the amplitude of the first cycle to that of the second cycle for an…

A:

Q: or a 3-cm thick slab that can be taken to be infinite in the x- and y-directions, the steady…

A:

Q: Refrigerant 134a at p₁ = 30 lb/in², T₁ = 40°F enters a compressor operating at steady state with a…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.