Which is the most accurate description of one of the system's processes? A Fluid moves from the secondary pipes into the ground. B Fluid moves from the primary pipe into the building. Fluids circulate separately inside both pipes. Fluid moves from the secondary pipe through the heat exchanger to the primary pipe.

Which is the most accurate description of one of the system's processes? A Fluid moves from the secondary pipes into the ground. B Fluid moves from the primary pipe into the building. Fluids circulate separately inside both pipes. Fluid moves from the secondary pipe through the heat exchanger to the primary pipe.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter49: Operation, Maintenance, And Troubleshooting Of Chilled-water Air-conditioning Systems

Section: Chapter Questions

Problem 6RQ: When condenser tubes become fouled, they may be cleaned by A. using a steel brush. B. using a brass...

See similar textbooks

Similar questions

(b) Bathroom sinks and some other fixtures include an overflow opening in the basin. This opening is located on the wall and near the top of the basin. The overflow opening serves two important functions: If the water tap is left on while the drain stopper is closed, the opening will channel water down into the drain opening rather than letting is spill out of the sink onto the floor. The overflow allows the sink to drain faster by introducing air into the system. A sink with a dimension given in Figure Q2(b), has water flows into it at a rate of 8 L/min. If the drain stopper is closed and water level in the sink remains constant, determine the average velocity of water flows through the 3.0 cm diameter overflow hole. Front 3 cm diameter overflow holes Q-8 L/min 15 3/4| 40 cm 15 cm Side (a) Figure Q2: (a) Picture of the sink; (b) Sink dimension (Ь)
Please answer questions g, h, and i. g.Calculate the heat transferred in the condenser. h.Calculate the diameter of the pipe connecting the turbine to the condenser. Design data for the plant shows the following pipe diameters. i. Calculatecooling water flow rate in GPM (‘gallons per minute’)through the condenser if the temperature of the cooling water increases from 13 C to 24 C in the condenser.
1. A temperature drop in the coolant entering the primary loop can be dangerous because,(a) Reactivity can increase as a result.(b) Pressure in the primary loop will decrease and water can flash to steam.(c) All of the above.(d) None of the above
What is a general equation that can be used to determine the velocity of a gas pump?
Questions Steam from the turbine exhausts directly into the (shell/water) of the 1. condenser. 2. As the steam flows down over the tube bundles it gives up (a) point, where it becomes liquid again. until it reaches the (b) 3. True or False a. The main steam condenser for a turbine is usually located below the turbine. b. One routine maintenance procedure frequently done inside a condenser is plugging tubes to clear them of blockage. 4. Name two safety precautions that must be taken before work may be safely performed inside the water boxes of a condenser. a. b. One way of keeping a unit of line if tube leakage is discovered while the unit is in service is the introduction of a biodegradable substance such as to the cooling water. 5.
Create a Refrigeration Cycle Steps: You can start at an point in the cycle, but you must follow this order and you must make it through the entire cycle. The following must be included and explained /defined Evaporation, Condensation, Fan for the Condenser and Blower for the evaporator. Provide good information Practice
What are the components of a pumping system?
A chiller tank with a water volume capacity of 20 M3. There are 2 chiller units with a capacity of 20 PK each to cool the water in the chiller tub. 1 unit of cold chiller water transfer pump is used to the production area with a capacity of 5 M3/hour. The chiller water temperature sent to production is 15 oC and the pressure is 4 bar. The distance of the 2 inch stainless pipe from the chiller pump to the double jacket mixing tank production is 100 meters. The diameter of the inlet and outlet pipes for the double jacket mixing tank is 1 inch. The chiller water storage capacity in a conventional double jacket mixing tank is 400 liters. (mixing tank capacity is 1500 kg). Questions: 1. How much time is needed to cool the water in the mixing tank from the initial temperature of 90 oC to 40 oC? 2. How much energy (BTU) is needed to cool the water temperature from 90 oC to 40 oC? 3. How much energy is lost along the 100 meters of chiller water transfer pipe? 4. If the number of 1500 Kg…
At the condenser, steam exits as a saturated mixture at the saturation temperature corresponding to the condenser pressure. True or False
What is the function of the empty pipes that connect from the sanitary/drainage pipes up through the roof of a building?
An oil/gas separator is a pressure vessel used for separating a well stream into gaseous and liquid components. They are installed either in an onshore processing station or on an offshore platform. Based on the vessel configurations, the oil/gas separators can be divided into horizontal, vertical, or spherical separators. In a vertical tank, the heavy liquids are pumped out of the ____________ of the vessel and the light phase is drawn off the side of the tank. a. Inlet b. corner c. Bottom d. Top
Possible problems an air conditioner can have and solutions to the problems