06. The lap joint is connected by three 20-mm diameter rivets. Assuming that the axial load P = 50 kN is distributed among the three rivets, find a. the shear stress in each rivet; b. the bearing stress between the plate and a rivet; the maximum average tensile stress in each plate. С. Express your answer in MPa 130 mm O O O 3/4 25 mm 25 mm

06. The lap joint is connected by three 20-mm diameter rivets. Assuming that the axial load P = 50 kN is distributed among the three rivets, find a. the shear stress in each rivet; b. the bearing stress between the plate and a rivet; the maximum average tensile stress in each plate. С. Express your answer in MPa 130 mm O O O 3/4 25 mm 25 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The axial load 229kN applied to the lap joint is distributed equally among the three 17.1-mm-diameter rivets. What is the maximum tensile stress (in Mpa) in the plate if w=139.6mm and t=29mm? Round off the final answer to three decimal places.
A link is loaded as shown, it is attached with two bolts with a diameter of 0.25 in. The link width is 2 lh and its thickness is 0.1 in, if the average normal stress in the link is 20 ksi (away from the bolts) determine the applied force G, the shear stress of a bolt as well as the bearing stress in one of the bolt holes. 2 in G
The cross-sectional area of each member of the truss is 42 cm2. B 6m E 6m 100 kN 300 kN Determine the following: a. Normal Stress in member CD b. Normal Stress in member CF c. Bearing Stress in member CD, tco= 18 mm, diameter of the rivet= 20 mm
Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?
3. The composite bar consists of a 20-mm diameter steel segment AB and 50-mm diameter brass end segments DA and CB. Find the stress on each segment due to the applied loads. E of steel is 200 GPa and E of brass is 101 GPa. 250mm 250mm 250mm 50mm 20mm 50mm 75KN 100KN brass steel brass D B C 75KN 100KN
The stress in a wire of diameter 2 mm if a load of 100 gm is applied to a wire.
A metal block of cross-section area A and length L is subject to a tensile stress of S. The block elongates by a length of 0.002L. Another block made from the same metal is subject to the same tensile stress. If this block has a cross-section area of 2A and a length of 2L, determine the elongation of the block.
The figure shows 16-mm diameter bolts used to hold two steel plates by fitting inside a cylindrical spacers. Thenormal stress must not to exceed 230 MPa in the bolts and 160 MPa in the spacer. Determine the outer diameterof the spacer.
The homogenous bar that weighs 5000 Ib is supported by a pin at Cand a cable that runs from A to B around the frictionless pulley at D. If the diameter of the cable is 0.8 inch, calculate its axial stress. Express your answer in ksi (kips per sq. inches) with one decimal place only (Note: Give only the numerical value of the answer. DO NOT INCLUDE THE UNIT IN THE ANSWER) * D F 3 ft 5 ft 5 ft
NEED ANSWER ASAP, THANK YOU A joint is made by gluing two plywood gussets of thickness t = 0.53 inCHES to wood boards. Determine the tensile stress for the plywood (in psi) if the dimension b = 15.73 in and the applied force is P = 7988 lb. Round off the final answer to three decimal places.
A rod is hanging vertically, supports a load of 20OON. Assume the weight of the wire is 1000N, determine the required diameter if the tensile stress is 140MPA. O 5 mm O 4.26 mm O 5.22 mm O 3.01 mm
Determine stress produced by tensile force of 20 N applied on cross sectional area of 5 mm2