Q4/: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10 t)] rms input signal has a load resistor of 3.3kQ. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VLP) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ?

Q4/: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10 t)] rms input signal has a load resistor of 3.3kQ. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VLP) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
Q4/: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10³t)] rms input signal has a load resistor of 3.3k2. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VL-P) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de voltage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.
b) Discuss the biasing and saturation voltage of a diode and Suggest how one can convert AC to the unidirectional DC output.
Negative Peak Clipper with bias circuit uses a germanium diode, with an input peak to peak voltage VPP=20 V and bias voltage VBias= 2.7 v. a) What is the function of the circuit? b) Draw the circuit diagram. c) Draw the input and output waveforms.
Write the following for a Semiconverter rectifier with RL load: a) Draw the circuit diagram, supply voltage and the output voltage waveform. b) Explain why there is no negative output voltage even without freewheeling diode. c) Derive the expression for average output voltage.
Draw the circuit diagram of a clipper that will produce an output waveform below. From the output waveform Voltage A is 6.7 and Voltage B is -9.7 .Input peak-to-peak voltage is given as 20 volts. Assume Silicon diodes are used. 1. For the positive half cycle, the needed battery voltage is........ 2. For the negative half cycle, the needed battery voltage is........
B. Draw the circuit diagram of a clipper that will produce an output waveform below. From the outp waveform Voltage A is 8.7 and Voltage B is -9.7.Input peak-to-peak voltage is given as 20 volts. Assi Silicon diodes are used. 7 B 1. For the positive half cycle, the needed battery voltage is 2. For the negative half cycle, the needed battery voltage is
b. Calculate the following about the circuit in the figure (If silicon diodes are employed in the rectification);i. the peak value of the output voltage considering the drop across each diode, Vpk.ii. the average voltage, Vdc. iii. The current through the load resistor, IL.iv. The current diode, Id.v. The frequency of the output signal, Fout.vi. Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch a graph of the input and output voltage against time.
For the circuit shown below, compute the maximum current through each resistor when terminal A is a) positive and, b) negative. Assume the diodes are ideal. (Will we convert to the RMS value to it's actual value?)
S-2) a) On the bridge type full wave rectifier circuit given in the figure Plot the current paths for each of the +/- alternans. b) The waveform of the Vç output voltage is given in the graphs on the side. Draw it in the blank and calculate the peak value and indicate it in the graph. c) Calculate the effective value of the output voltage. (Vç (eff) =… ..?). Note: Diodes are not ideal. VD = 0.7V.
Find the range of values that will keep the zener diode “on” (operating) in the figure. (Plot the Vy-Vi graph).
04: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10°t)] rms input signal has a loud resistor of 3.3k0. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VLp) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de valtage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.