Analyse the circuit ( write all necessary steps and formulae required and upload the answer sheet) 4:1 60 V a) What type.of circuit is this-Name it? (b) What is the total peak secondary voltage? (c) Sketch the output voltage waveform across RL. (d) How many diodes conduct during each cycle of the input wave? (e) Determine the peak inverse voltage (PIV) of the rectifier circuit?

Analyse the circuit ( write all necessary steps and formulae required and upload the answer sheet) 4:1 60 V a) What type.of circuit is this-Name it? (b) What is the total peak secondary voltage? (c) Sketch the output voltage waveform across RL. (d) How many diodes conduct during each cycle of the input wave? (e) Determine the peak inverse voltage (PIV) of the rectifier circuit?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
Negative Peak Clipper with bias circuit uses a germanium diode, with an input peak to peak voltage VPP=20 V and bias voltage VBias= 2.7 v. a) What is the function of the circuit? b) Draw the circuit diagram. c) Draw the input and output waveforms.
B. Draw the circuit diagram of a clipper that will produce an output waveform below. From the outp waveform Voltage A is 8.7 and Voltage B is -9.7.Input peak-to-peak voltage is given as 20 volts. Assi Silicon diodes are used. 7 B 1. For the positive half cycle, the needed battery voltage is 2. For the negative half cycle, the needed battery voltage is
Problem # 4 In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VpC e. PIV (Peak Inverse Voltage) 10:1 Dy 1ISV ms Ouiput RL 2.2 k2 D, 50 pF All diodes are IN4001. alleee
Negative Peak Clipper with bias circuit uses a germanium diode, with an input peak to peak voltage V=20 V and bias voltage V 2.7 v. a) What is the function of the circuit b) Draw the circuit diagram. c) Draw the input and output waveforms. Input Output
Q1 Figure Q1(a) is a full wave bridge circuit with a capacitor filter and the output waveform produced by the circuit is shown in Figure Q1(b). Assume all the diodes in the circuit have a forward voltage of 0.7 V. (a) Sketch the waveform in A, B, C and D as shown in Figure Q1(a).
ww. ETC CIMS Draw the output waveform for the given circuit diagram with proper values and also mention the name of the circuit. The input waveform Vi is having a peak-to-peak value of 15 V and the bias voltage is 3 V. Assume diode to be silicon. Vi Vo Maximum value of output waveform Minimum voltage of output waveform Finish
Q1 Figure Q1(a) is a full wave bridge circuit with a capacitor filter and the output waveform produced by the circuit is shown in Figure Q1(b). Assume all the diodes in the circuit have a forward voltage of 0.7 V. (a) (b) Sketch the waveform in A, B, C and D as shown in Figure Q1(a). Design the circuit by finding the value for the capacitor, C and the line voltage Vpri(rms) to the circuit to produce the output as shown in Figure Q1(b).
The diode from the following characteristic curve in Figure 1 was changed to zenerdiode. Determine: the function of zener diode in reverse biased. Briefly explain the differencebetween conventional diode and zener diode.
Determine the current I in the circuit (i). Assume the diodes to be of silicon and forward resistance of diodes to be zero.
0- Examine the circuits shown below for each half cycle. On each circuit indicate clearly which diode is on and show the path & direction of the currents. Use 2nd approximation for the diodes. a) What type of circuit is this? b) What is the total peak secondary voltage? c) Find the peak voltage across each half of the secondary (Circuit #1). d) Sketch the voltage waveform across R₁. Circuit #1 0 e) What is the peak current through each diode? f) What is the PIV (peak inverse voltage) for each diode? Circuit #2 120 Vrms 4:1 M: 120 V ms 00000 00000 D₁ LOKO R₁ 10 k Vp 120 V pe 120 V mms 100000 D₂ D₂ D₁ D₂ D₂ LORE R₁ 1.0 k