Design a full wave bridge rectifier power supply to deliver an average voltage of 20 V with a peak-to-peak ripple of 0.1 V to a load. The average load current is 15 mA. Assume that ideal diodes and 2 kHz ac voltage sources of any amplitudes needed are available. Draw the circuit diagram for your design. Specify the values of all the components used. Calculate the maximum diode current.

Design a full wave bridge rectifier power supply to deliver an average voltage of 20 V with a peak-to-peak ripple of 0.1 V to a load. The average load current is 15 mA. Assume that ideal diodes and 2 kHz ac voltage sources of any amplitudes needed are available. Draw the circuit diagram for your design. Specify the values of all the components used. Calculate the maximum diode current.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
For the circuit shown below, compute the maximum current through each resistor when terminal A is a) positive and, b) negative. Assume the diodes are ideal. (Will we convert to the RMS value to it's actual value?)
Consider the half-wave rectifier shown in the figure below. Let vs be a sinusoidal with 10V peak amplitude with frequency of 60Hz and let R = 1000 ohms. Use the contant voltage-drop diode model with VD = 0.7 V.
Draw the changes in Vi and Id of the ideal diode half-wave rectifier circuit in the figure. The frequency of the sine signal here will be taken as 50Hz. (Changes in Vi and Id will be drawn!!!)
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
Q4/: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10³t)] rms input signal has a load resistor of 3.3k2. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VL-P) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de voltage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.
Can someone please provide a step by step solution? Thank you! The full wave rectifier in the circuit below is to deliver 0.25A and 15V (peak) to a load. The ripple is to be no larger than 0.4 V peak-to-peak. The input signal is 120 V (rms) at 60 Hz. Assume V(lambda) = 0.7 V . Determine the required turns ratio, the filter capacitance, and the diode PIV rating.
Zener diodes are special purpose diodes designed to operate in their breakdown regions. Describe the working principle and characteristics of a typical Zener diode found in the market place. The Zener-diode regulator circuit shown below is to be used to provide a stabilised output to the load. The zener diode characteristic is also shown. Find the load voltage and source current if the battery voltage is 20 V, series resistance is 1.4 kohm and load resistance is 6 kohm
Determine the voltage across the diode, the output voltage, and the current in the resistor in the figure below. Plot these waveforms with proper ac cycle phase alignment. 1SR154-400 is a silicon rectifier 1 ampere diode. Indicate the peak values as per calculation.
A three-phase half wave rectifier has a supply of 150V/phase. Determine the mean load voltage and the required diode rating, assuming the load current is level at 25A. Assume each diode has a volt-drop of 0.7V.
For the circuit shown below, compute the maximum current through each resistor when terminal A is a) positive and, b) negative. Assume the diodes are ideal.
For each circuit shown below, the input v, is a 60HZ, 12 volt peak sine wave. Sketch the waveform resulting at vo. Assume ideal diodes. What are its positive and negative peak values?