Q4/: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 103t)] rms input signal has a load resistor of 3.3kN. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VL-p) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ?

Q4/: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 103t)] rms input signal has a load resistor of 3.3kN. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VL-p) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ?

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

Write the following for a Semiconverter rectifier with RL load: a) Draw the circuit diagram, supply voltage and the output voltage waveform. b) Explain why there is no negative output voltage even without freewheeling diode. c) Derive the expression for average output voltage.
S-2) a) On the bridge type full wave rectifier circuit given in the figure Plot the current paths for each of the +/- alternans. b) The waveform of the Vç output voltage is given in the graphs on the side. Draw it in the blank and calculate the peak value and indicate it in the graph. c) Calculate the effective value of the output voltage. (Vç (eff) =… ..?). Note: Diodes are not ideal. VD = 0.7V.
For the circuit shown below, compute the maximum current through each resistor when terminal A is a) positive and, b) negative. Assume the diodes are ideal. (Will we convert to the RMS value to it's actual value?)
Draw the changes in Vi and Id of the ideal diode half-wave rectifier circuit in the figure. The frequency of the sine signal here will be taken as 50Hz. (Changes in Vi and Id will be drawn!!!)
Can someone please provide a step by step solution? Thank you! The full wave rectifier in the circuit below is to deliver 0.25A and 15V (peak) to a load. The ripple is to be no larger than 0.4 V peak-to-peak. The input signal is 120 V (rms) at 60 Hz. Assume V(lambda) = 0.7 V . Determine the required turns ratio, the filter capacitance, and the diode PIV rating.
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
Consider the half-wave rectifier shown in the figure below. Let vs be a sinusoidal with 10V peak amplitude with frequency of 60Hz and let R = 1000 ohms. Use the contant voltage-drop diode model with VD = 0.7 V.
A half-wave recitifier is connected to a 50V AC source. If the load resistance is 100 ohms, find: 1) Max load voltage 2) Average load voltage 3) Max load current 4) Average load current 5) RMS load current 6) PIV rating for diode ...
1N4001, 1N4002, 1N4003, 1N4004, 1N4005, 1N4006 and 1N4007 For any of the diodes, describe with the aid of diagrams/illustrations its applications in an AC to DC Bridge rectifier power supply circuit. For your circuit show and describe how you are going to smooth out the ripple voltage that will be present.
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: Peak AC voltage Vm of the source a) b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance vs(t) K Load UL
b) Discuss the biasing and saturation voltage of a diode and Suggest how one can convert AC to the unidirectional DC output.
Sketch current I vs, voltage V for the circuits below. The breakdown voltage of the Zener diodes are shown. Assume 0.6V for all diodes (including Zener diodes) in the forward bias region.