Q3 A common emitter BJT circuit is designed as shown in Fig. 4(a). The output load line and defined Q-point of the circuit are shown in Fig. Determine the required values of Vcc, Rc and RB. Assume that VBE .(on)=0.7 V + Vcc 12 'c(mA) 10 RC 8. -IB3 = 30 µA O-point RB 6. Ig2 = 20 µA VCE ww 4 IB1 = 10 µA VBE VBB = 10 V VcE (V) 10 15 20 25

Q3 A common emitter BJT circuit is designed as shown in Fig. 4(a). The output load line and defined Q-point of the circuit are shown in Fig. Determine the required values of Vcc, Rc and RB. Assume that VBE .(on)=0.7 V + Vcc 12 'c(mA) 10 RC 8. -IB3 = 30 µA O-point RB 6. Ig2 = 20 µA VCE ww 4 IB1 = 10 µA VBE VBB = 10 V VcE (V) 10 15 20 25

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

This is Electronic Devices about BJT. Find the Base Voltage Vb, Emitter Voltage Ve and Collector Voltage Vc using the Thevenin Theorem. draw the Thevenin equivalent circuit.
Most of the following statements about integrated circuits arecorrect, but one is not. Which statement is NOT true? Select one: a. Transistors are constructed in a small area of an integrated circuit,and are connected to other transistors by wires that are embedded inthe integrated circuit b. Wires that carry signals may be embedded in a substrate without a shortcircuit because a short circuit would require a signal to cross areverse biased junction c. Each transistor on an integrated circuit is manufactured individually,one at a time d. An integrated circuit contains several layers
Figure 1 shows the typical output characteristics of MOSFET. Those characteristics show the difference curve of the drain current, Ip, as function of the drain- source voltage, VDs at a given gate-source voltage, VGs. In the Figure 1, it shows that the Ohmic region. What the meaning of the Ohmic region? Explain with necessary example any consequences that will happen for any condition of MOSFET. 360 10 V ev 7V 320 280 Ohmic region + 240 200 160 120 5.5 V- 80 40 2 3 Vos [V] Figure 1 lo [A]
Complete the given BJT circuit. Solve for the value of the resistors and the voltage supply that will satisfy the given DC loadline. Assume IC=IE and RC=RE. Show and label properly the required final circuit. 5 mA 2.5 mA * IC IC 0 15 V 30V VCE RB B +VCC C E RC B=100 RE ...
Determine (a) VGS (b) ID (c) VDS (d) VD for the following FET biasing configuration in theFig.Q4(e). Here, VDD is 89v.
Label properly the required final circuit and DC loadline. Complete the given BJT circuit. Solve for the value of the resistors and voltage supply that will satisfy the given loadline
A silicon transistor is biased with base resistor method. If B=100, VBE =0.7 V, zero signal collector current IC = 1 mA and VCC = 6V , what is the %3D value of the base resistor RB? Select one: a. 530 kQ b. 105 kQ c. 315 k. d. None of the above
A certain npn silicon transistor has vBE=0.7 V for iB=0.1 mA at a temperature of 30°C. Sketch the input characteristic to scale at 30°C. What is the approximate value of vBE for iB = 0.1 mA at 180°C? (Use the rule of thumb that vBE is reduced in magnitude by 2 mV per degree increase in temperature.) Sketch the input characteristic to scale at 180°C.
b) For correct operation as an ac amplifier a npn BJT must be correctly DC biased to establish an appropriate Q-point, i.e a negative voltage VBC between the base and collector terminals and a positive voltage VBE between the base and emitter terminals. Figure 3.1 shows a circuit that can achieve this requirement. Explain the role of each resistive element in this circuit. Vin RB1 Cin iin 5 RB2 www ww 20⁰ Rc VB, RE + Vcc Vc Cout VE Figure 3.1 Vout Ce ¡out
a. In the circuit shown, measurements give Vg = + 4.3 V and Vc = + 2.3 V. Determine the mode of the silicon BJT and calculate the base current, the emitter current and B of the transistor. b. Now replace the 20 KO resistor by a silicon diode with anode connected to the base of BJT. Determine the state of the transistor and calculate the base current. +5 V o ve 20 kn 230 N
NPN BJTs can be used as emitter followers. In the given circuit, the follower is connected to a non-ideal voltage source (Vs) with a source resistance (Rs) What should be the value of Vs for the BJT to start saturating of Rs = 5k ohms.
In CB configuration, the value of a=0.98A. A voltage drop of 4.9V is obtained across the resistor of 5KQ when connected in collector circuit. Find the base current. a) 0.01mA b) 0.07MA c) 0.02mA d) 0.05mA