For correct operation as an ac amplifier a npn BJT must be correctly DC biased to establish an appropriate Q-point, i.e a negative voltage VBC between the base and collector terminals and a positive voltage VBE between the base and emitter terminals. Figure 3.1 shows a circuit that can achieve this requirement. Explain the role of each resistive element in this circuit.

For correct operation as an ac amplifier a npn BJT must be correctly DC biased to establish an appropriate Q-point, i.e a negative voltage VBC between the base and collector terminals and a positive voltage VBE between the base and emitter terminals. Figure 3.1 shows a circuit that can achieve this requirement. Explain the role of each resistive element in this circuit.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. Write down which transistor structure each curve characteristic belongs to in the figure. Ip -VGS -VGS +VGs (c) VGS (b) (a)
QUESTION 4 In this voltage divider bias circuit, the input is at the base. Output is at the emitter with a high input resistance and low output resistance. The maximum voltage gain is 1 and the coupling capacitors must have a negligible reactance at the frequency of operation. (use to answer a and b) a. Derive the expression for the voltage gain, current gain, and power gain in terms of power delivered to the load, RL. b. Sketch both the DC and AC equivalent circuits. c. Derive the expression for ripple factor of Half Wave Rectification with a capacitor filter.
Determine VB, VE, VC, VCE, IB, IE, and IC in Figure. The 2N3904 is a general purpose transistor with a typical BDC 200 Vcc +30 V WWII VCE VB R₁ • 22 ΚΩ IC(mA) Chọn... * Chọn... * IB(UA) Chọn... * IE(MA) Chọn... ◆ Chọn... * Chọn... * Chọn... * VE VC R₂ ´ 10 ΚΩ www Rc 1.0 ΚΩ 2N3904 PDC=200 RE 1.0 ΚΩ
In this voltage divider bias circuit, the input is at the base. Output is at the emitter with a high input resistance and low output resistance. The maximum voltage gain is 1 and the coupling capacitors must have a negligible reactance at the frequency of operation. (use to answer a and b) a. Derive the expression for the voltage gain, current gain, and power gain in terms of power delivered to the load, R. b. Sketch both the DC and AC equivalent circuits. c. Derive the expression for ripple factor of Half Wave Rectification with a capacitor filter.
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
For the circuit given in figure below draw the collector characteristic curves for IB = 50,150 and 250 micro amperes on the same graph
Design a DC-DC converter of the circuit with the following specifications: Input voltage (12-40) V; output voltage 24 V; output current is varied from (2 to 4)A: C.C.M with output voltage ripple not more than 1%. Knowing that the switching frequency is 25 kHz. Also draw the current waveforms. And give the Design specifications of diode (PIV, and Vavg ,I peak) and (V Diod , I Diod) of Diode. Buck Boost Converter lin ip + T | Va R ic i.
A Bipolar junction Transistor with curreat amplification factor being 100, Input Base current is 50μA. Collector voltage is 10 V and biasing voltage being +20 V. Find followings a. Collector current b. Resistance (R1) c. Collector voltage , Emitter voltage , Base Voltage & Collector-Emitter Voltage.
Q-3. Find the drain-source voltage, Vos, for the E- MOSFET circuit given below. The device parameters are: Ioss = 4 mA and Vm = 2 V. +15V Rp- 2k 4M R1 + Vps 2M R2
1. The DC-DC converter has several circuit configurations. a) (Draw a simple connection of IGBT switch, diode and inductor that can discriminate between Buck, Boost and Buck-Boost converter circuits respectively.) b) ('A Boost converter produces an output voltage, Vo that is more than or equal to the input voltage, Vi. Based on this statement develop the equation for the relationship between Vo Viand D. where D represents the duty ratio. You can use any suitable diagram to illustrate your answer.)
04:- Design a bias circuit for NPN silicon transistor having a nominal B-100 to be used in voltage divider circuit with Q-point of Ic 10 mA and VCE = 10 V. Use standard valued 5% resistors and draw a schematic diagram of your design. (10 points)
One of the following is not a property of a common-emitter amplifier: Select one: a. high voltage gain b. No phase inversion c. high current gain d. Emitter is at ac ground