A common emitter BJT circuit is designed as shown in Fig. 4(a). The output load line and defined Q-point of the circuit are shown in Fig. Determine the required values of Vcc, Rc and RB. Assume that VBE (on)=0.7 .V Vcc 12 e(mA) 10 RC - Ig3 = 30 µA @ point -192 = 20 µA R 6. ww VCE -Ia1 = 10 µA VBE Van VeV) = 10 V 5 10 15 20 25 إجابتك

A common emitter BJT circuit is designed as shown in Fig. 4(a). The output load line and defined Q-point of the circuit are shown in Fig. Determine the required values of Vcc, Rc and RB. Assume that VBE (on)=0.7 .V Vcc 12 e(mA) 10 RC - Ig3 = 30 µA @ point -192 = 20 µA R 6. ww VCE -Ia1 = 10 µA VBE Van VeV) = 10 V 5 10 15 20 25 إجابتك

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

FOLLOW UP QUESTIONS: BIPOLAR JUNCTION TRANSISTOR (BJT) SOLVE FOR: a.) VL(p-p) if Rs is 1KOhm b.) Ais if Rs connected is 1KOhm
a. In the circuit shown, measurements give Vg = + 4.3 V and Vc = + 2.3 V. Determine the mode of the silicon BJT and calculate the base current, the emitter current and B of the transistor. b. Now replace the 20 KO resistor by a silicon diode with anode connected to the base of BJT. Determine the state of the transistor and calculate the base current. +5 V o ve 20 kn 230 N
Most of the following statements about integrated circuits arecorrect, but one is not. Which statement is NOT true? Select one: a. Transistors are constructed in a small area of an integrated circuit,and are connected to other transistors by wires that are embedded inthe integrated circuit b. Wires that carry signals may be embedded in a substrate without a shortcircuit because a short circuit would require a signal to cross areverse biased junction c. Each transistor on an integrated circuit is manufactured individually,one at a time d. An integrated circuit contains several layers
Given: Vth is 1.2V and k is 0.5 mA/V² Solve for the following with at least 4 significant figures. Current is in mA and Voltages in V. 1. Id, Vgs, Vds. 2. Verify your MOSFET's mode of operation.
2. For the emitter-stabilized bias circuit, determine: a. IBQ. b. IcQ. c. VCEQ. d. Vc. e. V B. f. VE. 20 V 470 2 ICQ 270 k2 oVc VB B= 125 VCEQ IBQ OVE 2.2 k2
A certain npn silicon transistor has vBE=0.7 V for iB=0.1 mA at a temperature of 30°C. Sketch the input characteristic to scale at 30°C. What is the approximate value of vBE for iB = 0.1 mA at 180°C? (Use the rule of thumb that vBE is reduced in magnitude by 2 mV per degree increase in temperature.) Sketch the input characteristic to scale at 180°C.
The problem are DC analysis problems. For each of the circuits verify the mode of operation and solve for all applicable DC voltages and currents. > When you "verify" a mode of operation you will need to calculate all three voltages (Vc, V8, VE for BJTS and VG, Vs, Vo for MOSFETS) and show the correct two conditions are satisfied. > Assume Capacitors acts like open circuits at DC and short circuits for AC. > Assume the following: o Beta = 100 O VBE = 0.7 o V (Thermal) = 26 mV o V (Threshold) = 2V O VA = - !! For MOSFET saturation mode: assume Ip = K(VGs-Vr)? (Assume K = 10 mA/V?). 12V R2 >2kn R1 10kn R4 (R3
3. Below is a BJT based amplifier 3.9k2 37 Vi I B-100 4.7ks a. Find IB, IE b. Draw the load line for this transistor showing the operation point for this network c. Draw the n and T network AC circuit for this network d. Find r. e. Find Z; and Z, for r, = 70 Kiloohms f. Find Ap g. The circuit shown is placed in a karaoke machine, explain why the quality of sound from the speakers becomes bad as the singer starts singing loudly and has the best quality when singing softly. What is this phenomenon called?
Referring to the Ic vs. Vce plot shown for a BJT, and for a base current of 100 μA, over what voltage range for Vce (within 0 - 15 V) would you expect the transistor to work well as an amplifier? Explain your reasoning, referring to the diagram. [mA], COLLECTOR CURRENT L=400μA -350μA L=300μA . 1-250A 200μA 150µA -100μA -50μA 10 12 VM. COLLECTOR-EMITTER VOLTAGE 16
The collector supply voltage is 6 V and the voltagedrop across a resistor of 600 Ω in the  collector circuit is0.6 V, in a transistor connected in common emittermode. If the current gain is 20, the base current is A. 0.25 MAB. 0.05 mA C. 0.02 mAD. 0.07 mA
D Question 4 Find the base and collector currents for each of the following two circuits. Assume a base- emitter voltage of 0.7. R1 1 Meg R1 1 Meg. R2 5k Q1 generic AND .op .model generic NPN(BF=100) R2 10k Q1 generic R3 10k + .op .model generic NPN(BF=100) Vcc Vcc 10.7 10.7
4) An npn transistor is accidentally connected with col- lector and emitter leads interchanged. The resulting currents in the normal emitter and base leads are 0.5 mA and 1 mA, respectively. What are the values of aR and Br?