Problem 2 A simply supported timber beam has a span of 6 m long and carries a uniformly distributed load of 28 KN/m over its entire span. This load already includes an allowance for beam weight. The timber is 80% stress grade Apitong. The allowable deflection is of the span. The properties of 1 240 the Apitong are given. i. E = 7.31 x10³ Mpa F = 1.73 Mpa Which of the following gives the smallest dimension of the beam such that the allowable shear stress is not exceeded. a. 220 mm x 440 mm b. 150 mm x 300 mm c. 200 mm x 400 mm

Problem 2 A simply supported timber beam has a span of 6 m long and carries a uniformly distributed load of 28 KN/m over its entire span. This load already includes an allowance for beam weight. The timber is 80% stress grade Apitong. The allowable deflection is of the span. The properties of 1 240 the Apitong are given. i. E = 7.31 x10³ Mpa F = 1.73 Mpa Which of the following gives the smallest dimension of the beam such that the allowable shear stress is not exceeded. a. 220 mm x 440 mm b. 150 mm x 300 mm c. 200 mm x 400 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cantilever beam with a ‘T’ shaped cross-section is loaded with a distributed load as shown below. The intensity of the distributed load is 100N/mm. b = 6.25mm and c=6.25mm. Parameter Description Value UnitsL Beam length 250 mm a Width of the flange 80 mm d Height of the web 75 mm σ Yield stress 250 MPa You are tasked with ensuring the beam can withstand the applied loading. To do this you must: Create a two-dimensional contour plot of the bending and transverse shear stresses over the length and height of the beam (xy plane). You can use your results above to validate your approach. Note: perform these calculations in a program such as Matlab or Python. Provide the script.
A cantilever beam with a ‘T’ shaped cross-section is loaded with a distributed load as shown below.The intensity of the distributed load is 100N/mm. b = 6.25mm and c=6.25mm.Parameter Description Value UnitsL - Beam length 250 mma - Width of the flange 80 mmd - Height of the web 75 mmσ - Yield stress 250 MPaYou are tasked with ensuring the beam can withstand the applied loading. To do this you must:a) Calculate the centroid for the given cross-section. Your value of ?ത should be measured fromthe bottom of the section. Determine an expression for Q (statical moment of area) for thegiven shape. The expression(s) for Q should be in terms of the variable, y, measured from thebottom of the section. b) Create a graph of the shear and bending stresses at the fixed support (B) over the crosssection. The stresses should be plotted as a function of y, measured from the bottom of thesection.
12. Assume a uniformly load simply support beam with a rectangular cross section. The width of the beam is fixed by other design considerations. Determine the ratio between the difference in depth required for an aluminum beam compared to a steel beam in order to obtain the same maximum deflection. MOE aluminum can be taken as 10,000 ksi, for steel as 30,000 ksi. The maximum deflection for the beam is 5wl*/384EI Factoring the deflection equations we can conclude that for equal deflection Eala = Esls where subscripts a and s represent values for aluminum and steel. The depth of must be times the depth of the
What is the long-term deflection for dead load plus 45% permanent live load for 1 year, there is superior steel with p' = 0.012. Assume 8l = 0.289 in., SD = 0.163 in., Ssl = 0.090 in.
4) A simply supported beam supports the uniformly distributed load of intensity Wo. Determine the safe allowable value of w, if the flexural stress is limited to 160 MPa in tension, 200 MPa in compression, shear stress is limited to 70 MPa and maximum allowable deflection is 15mm. The modulus of elasticity of the beam is 200 GPa. Use Moment Area Method. Prepare A 1m B Wo 3m 2m 30 230 m 10 10 10 (dimensions in mm) 150
Q2/ Find (x) so that the rigid beam remains in a horizontal position. Aluminum L = 5m A = 400mm² E = 70GPA Steel L = 3m A = 500mm? E = 200GPA 5m %3D Rigid beam Answer: x = 0.719m P = 50kN
Rod AB is made of a mild steel that is assumed to be elastoplastic with E = 200 GPa and oy =250MPA . After the rod has been attached to the rigid lever CD, it is found that end C is 6 mm too high. A vertical force Q is then applied at C until this point has moved to position C'. Determine the required magnitude of Q and the deflection ô, if the lever is to snap back to a horizontal position after Q is removed. 9-mm diameter 1.25 m 6 mm 0.7 m 0.4 m
What will be the safe weight per linear meter length of the beams if the displacement at E is limited at 8mm. Where x=14.37m. = Properties of Steel: Ast 300mm², Est-200 GPa, Lst=2m = Properties of Steel: Aal 500mm², Eal-70 GPa, Lal=2m 0:5X Whit ALUMINUM x STEEL с
Question 6 The reinforced concrete beam shown in Figure 6 is encastré at both ends. It supports a udl over part of the span as shown. The beam has a cross section 300mm wide by 900mm deep. Take the E value of the concrete as 15GPA. Use the gross concrete section properties in any calculations. (1) (ii) Using the Differential equations of flexure, determine all the reactions Calculate the vertical deflection at the midspan of the beam in mm. Calculate the max sagging moment in the span. (iii) 100KN/m B 8m 6m Figure 6
For the beam geometry shown, determine the following: a. Cracking moment b. Has the beam section already cracked? c. Determine the bending stresses at the extreme fibers of the beam. Applied moment = 34kN/m fc = 21 MPa As = 1935mm² n=9 250mm 00 400mm 75mm
A square beam (w=0.03 m) is loaded with a point load of 1000 N and a moment load of 1000 Nm, as shown. i. Determine maximum deflection of the beam using step by step analytical equations. ii. Determine the Maximum stress in the beam using step by step analytical equations iii. For both top fibers and bottom fibers of the square beam, specify the type of the stresses.
Therectangular wood beam is loaded asshown in the figure. Solve thefollowing:What is the maximum bendingstress in the beam?What is the maximum shear stress in the beam?