What will be the safe weight perlinear meter length of the beamsif the displacement at E is limitedat 8mm. Where x=14.37m.=Properties of Steel: Ast300mm², Est-200 GPa, Lst=2m=Properties of Steel: Aal500mm², Eal-70 GPa, Lal=2m0:5XWhitALUMINUMxSTEELс

Answered: Image /qna-images/answer/ab0a9694-48fe-4969-b2a0-15bde19eb926.jpg

What will be the safe weight pe linear meter length of the beam if the displacement at E is limite at 8mm. Where x=14.37m. Properties of Steel: Ast = 300mm², Est-200 GPa, Lst=2m Properties of Steel: Aal =

What will be the safe weight pe linear meter length of the beam if the displacement at E is limite at 8mm. Where x=14.37m. Properties of Steel: Ast = 300mm², Est-200 GPa, Lst=2m Properties of Steel: Aal =

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(40 Hiw A Pismatic steel bar ofa Square cross section (loo*lo0)mm is looled by Comressive force P= 1300 kU, the bar has length 2.5 m, Eg=200 G Pa, V=0.3,determine the Shortening d, the increase in the dimensions of cross Section , the change in Volume DV of the bar? loomm Joomm
10. The hoisting beam assembly shown is supported by two 20- mm-diameter bolts at A and a 150 mm x 200 mm plate at B. In this problem, a = 1.2 m and b = 2.8 m. If the allowable tensile stress of the bolts at A is 112 MPa, which of the following gives the maximum safe value of W in KN? A. 45 C. 30 B. 60 D. 15 ZEIT 0 a BEEN H 8804 pe (cAPlate B to tried man 11 of 1911 b bell 110 mb llame lis To 102 W 20-102 bugil noitsuta
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
A cantilever beam with a 'T' shaped cross-section is loaded with a distributed load as shown below. The intensity of the distributed load is 100N/mm. b = 6.25mm and c=6.25mm. A y Parameter L a d 0 L B 777 Description Beam length T Width of the flange Height of the web Yield stress |←0 →| Value 250 80 75 250 y Units mm mm mm MPa You are tasked with ensuring the beam can withstand the applied loading. To do this you must: a) Calculate the centroid for the given cross-section. Your value of y should be measured from the bottom of the section. Determine an expression for Q (statical moment of area) for the given shape. The expression(s) for Q should be in terms of the variable, y, measured from the bottom of the section.
А L B 425 mm C 1,000 mm V P A steel bar (1) and an Aluminum bar (2) are connected to a rigid angle ACD. Assuming: • Steel [E = 200 GPa] bar (1) is 6mm x 40mm x 600mm long. • Aluminum [E = 70 GPa] bar (2) is 10mm x 40mm x 600mm long. Poisson's ratio, v = 0.35 • A distance L of 500mm. a)Determine the force P (in kN) required to stretch the Aluminum bar by 1mm. Enter the force, P, into the d21 answer box (in kN, 3 sig digs). b) Determine the final width and thickness of the Aluminum bar. (1) Your Answer:
For the box beam shown in Fig. if the modulus of elasticity E = 200 GPa, the flexural stresses at support for point (a) is ..................... MPa * 120mm 16.2kN 16.2KkN —{ 10.2KN/m £ fj//’/ £ W @ Q| im 3m im = 30 mm thickness of walls cross section Your answer
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1= 0.8 m; B2 = 1.0 m; B3= 0.6 m. Determine the axial load acting on bar B3 in kN. 35KN В1 B2 ВЗ ... 10KN 15KN 30KN A 35 20 10 D 5
For the exact in the figure tensile strength = 8000 N/cm^2 compression safety = 3000 N/cm^ 2 calculate the largest Mx moment that the section can carry. S-2) 2.5 3 как 2.S cm pomk CM AA 3.5 3.5 3 CM x<- vy 18cm 15 Cm 5cm
The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point P (very close to the bottom of the flange) is 12 MPa. The stress at point Q In the web (very close to the flange) is: N'-. 100- P Q 201 100- T 20 81484 80 20 40 --N (a) Indeterminable due to incomplete data (6) 60 MPa (c) 18 MPa (d) 12 MPa 068
A steel rod (E=29000ksi) was pulled by a 2kip force. The initial length of the rod is 3ft and the radius is 1in. Solve the deformation. O 0.00079in O 0.00020in O 0.00316in O 0.00119in
A cantilever beam with a ‘T’ shaped cross-section is loaded with a distributed load as shown below.The intensity of the distributed load is 100N/mm. b = 6.25mm and c=6.25mm.Parameter Description Value UnitsL - Beam length 250 mma - Width of the flange 80 mmd - Height of the web 75 mmσ - Yield stress 250 MPaYou are tasked with ensuring the beam can withstand the applied loading. To do this you must:a) Calculate the centroid for the given cross-section. Your value of ?ത should be measured fromthe bottom of the section. Determine an expression for Q (statical moment of area) for thegiven shape. The expression(s) for Q should be in terms of the variable, y, measured from thebottom of the section. b) Create a graph of the shear and bending stresses at the fixed support (B) over the crosssection. The stresses should be plotted as a function of y, measured from the bottom of thesection.
A beam cross section is shown. If the beam is subjected to a moment of 400N.m, the maximum bending stress will be? I, = 200 mm 4 8 mm 4 mm O a. 16GPA О Б. 10GPa 12GPA O d. 8GPA