Determine the degree of freedom of the mechanism in the figure below. Then determine all thecenters of the era. Then use it to find the angular velocity of link 4 as well as the slidingvelocity, knowing w_2 = 10 rad /s clockwise. Note that you must specify the order and methodof determining non-obvious centers.%3DPE45D.CBLink radius 2:-25mmLink radius 5:-10mmBD length: -55 and DE length=30mm its angle with a horizon of 45 degrees and also the radius of curvature of the earth at point F isequal to 20 mm. The segment AB is horizontal and BD is vertical. The contact at point Cis of the rolling type with slip and at point Fthe rolling is pure.2.

Please see the attached detailed solution:

Determine the degree of freedom of the mechanism in the figure below. Then determine all the centers of the era. Then use it to find the angular velocity of link 4 as well as the sliding velocity, knowing w_2 = 10 rad /s clockwise. Note that you must specify the order and method of determining non-obvious centers. E 4 5.

Determine the degree of freedom of the mechanism in the figure below. Then determine all the centers of the era. Then use it to find the angular velocity of link 4 as well as the sliding velocity, knowing w_2 = 10 rad /s clockwise. Note that you must specify the order and method of determining non-obvious centers. E 4 5.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Refer to the figure below for the mechanism. If link 2 rotates at a speed of 60 revolutions per minute in a counterclockwise direction , find the velocity, using resolution and composition method of: A point connecting link 2 to link 3 A point at the center of link 2 A point at the center of link 3 Of the slider Also, locate all the instantaneous centers.
Select Suitable scale to draw position, velocity and Acceleration diagrams and determine unknowns for the following questions: Q1. Determine the angular velocity (0) and angular acceleration (C) ofLink DC of the four bar linkage mechanism shown in figure 1. Input link AB rotates at 100 rev/min in anti-clo ckwise direction with uniform velo city. C 300 mm 600 mm DI B. 300 400 mm (450 A Figure 1 Q2. Find the velocity and a cceleration ofthe piston and the angular velocity and angular acceleration of link AB for the crank slider mechanism sho wn in figure 2. The crank OA rotates anti-clo ckwise at 500 rad/min with constant velo city. Point O is fixed. A 100 mm 200 mm 600 B. 45° Figure 2
Refer to the figure below for the mechanism.If link 2 rotates at a speed of 60 revolutions per minute, find the velocity, using resolution and composition method of: A point connecting link 2 to link 3 A point at the center of link 2 A point at the center of link 3 Of the slider Also, locate all the instantaneous centers. Use counterclockwise direction.
Refer to the figure below for the mechanism. If link 2 rotates at a speed of 60 revolutions per minute, find the velocity, using resolution and composition method of: A point connecting link 2 to link 3 A point at the center of link 2 A point at the center of link 3 Of the slider Also, locate all the instantaneous centers. Use counterclockwise direction.
Problem 4: A four bar linkage is shown below with crank Q2A, 1 foot long and crank 2 rotates clockwise with an instantaneous angular velocity of 152.79 rpm. The rest of the members are drawn to scale. Solve for the Velocity of point A and find the velocities of B, C, D, E and F using RESOLUTION AND COMPOSITION METHOD only! Ks = 1 inch : 1 foot Kv = 1 inch : 16 fps
theta O = 55 The link length and value of O2 for some four bar linkage are defined below, (drive link =4.2 cm , coupler link =5.9 cm , follower link = 5.9 cm, fixed link= 6.85 cm 1. draw the linkage to scale and graphically find all possible solution (both open and cross) for 03 and O4 2. If w = 2 rad /s (CCW) find the angular velocity for bar 3 and 4 3.if a= 5 rad/s? (Ccw) find the normal and tangential acceleration for link 3 and 4
Calculate the acceleration of point A with respect to origin point 0. Remember that like velocity, you need to calculate each link's relative velocity and then add them all up: aa/O = aa/3 + ag/o Also, each relative acceleration can be calculated using its two components in radial and direction, for example: a4/5 = ar, A/B + ag, a/B 0,0, Ö li = 25.0cm %3D 01 = 45.0deg w1 = 0.5rad/s a1 = 1.0rad/s² r2 0 = 45deg 12 = 20.0cm O2 = 30.0deg 02 = 30.0deg w2 = 0.5rad/s a2 = 0.0rad/s²
The figure shows a linkage in one position. What is the instantaneous acceleration of point P if the link O₂A is rotating CW at 40 rad/sec? 8.9 5 B 4.4 5 56° 500 9.5 02 140 8,000 in/sec2 04 O 15,282 in/sec2 O 9,005.8 in/sec2 O 23,073 in/sec2
According to the below figure, if the rotational velocity of link AB is constant and equal to 2 rad/s (wAB = 2rad/s), find the velocity of point E. This problem should be solved based on the concept of the 400 mm instantaneous center of rotation. Other methods are not acceptable. 700 mm 400 700 mm mm
The general linkage configuration and terminology for an offset fourbar slider-crank linkage are shown in Figure below. The link lengths and the values of 02 and w2 are defined in. For the row(s) b and c, find the velocities of the pin joints A and B and the velocity of slip at the sliding joint using an analytical method. Draw the linkage to scale and label it before setting up the equations. Link 3 Offset 04 = 90° Link 2 02 Slider position d TABLE P6-2 Data for Problems 6-6 to 6-7† Row Link 2 Link 3 Offset 02 1.4 4 1. 45 10 2 6. -3 60 -12 3 8. -30 -15
Crack AB of a slider crack mechanism shown in Figure 2 rotate at a constant speed of 300 rpm in clockwise direction. The connecting rod BC has a length of 1 m and incline at 45o to vertically positioned piston C. No angle or length for AB is given in the original question, thus I assume the angle is 70o because of the rough drawing I did here. Draw the displacement diagram of the mechanism shown in Figure 2 to scale. Use a vector diagram to determine the velocity of the piston C and connecting rod BC. Calculate the acceleration of piston C and the angular acceleration of connecting rod BC.
Find the velocity of point B and angular velocity in link 3 using relative analysis and polygon method. Note the drawing is not in scale. B 02 @2=1 rad/s 2 30° A 1 3 4 04 02A=4" AB=7" 0204-=9" 04B=8"