3. 4 Fig. 3- 5 shows the internal structure of an internal combustion engine which has AB = 10cm, and BC = 10 3 cm. The angle velocity of the crank shaft is 30rad/s, and LACB is shown in position. 1) Draw the kinematic diagram of this mechanism. 2) Find out all instantaneous centers. 3) Determine the velocity of the piston in the position shown. 30

3. 4 Fig. 3- 5 shows the internal structure of an internal combustion engine which has AB = 10cm, and BC = 10 3 cm. The angle velocity of the crank shaft is 30rad/s, and LACB is shown in position. 1) Draw the kinematic diagram of this mechanism. 2) Find out all instantaneous centers. 3) Determine the velocity of the piston in the position shown. 30

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the degree of freedom of the mechanism in the figure below. Then determine all the centers of the era. Then use it to find the angular velocity of link 4 as well as the sliding velocity, knowing w_2 = 10 rad /s clockwise. Note that you must specify the order and method of determining non-obvious centers. %3D PE 4 5 D. C B Link radius 2:-25mm Link radius 5:-10mm BD length: -55 and DE length=30mm its angle with a horizon of 45 degrees and also the radius of curvature of the earth at point F is equal to 20 mm. The segment AB is horizontal and BD is vertical. The contact at point Cis of the rolling type with slip and at point F the rolling is pure. 2.
Find out the velocity of slider D and angular velocity of CD in the mechanism shown below. Take Q1A= Q2B = 2cm; Q1Q2 = 4 cm; CD = 6 cm and wQ,A rad = 1 sec Solve using instantaneous center method. Use CCW direction. 20 QI 1 A Q2 20
(Use relative motion analysis): The planetary gear system is used in car transmissions. There is sun gear S, planet gears P and the ring gear R. By locking (fixing/grounding) certain gears you can have different gear ratios and car speeds. = c) If the output shaft is held fixed, i.e. WA 0, and the ring gear is rotated at WR 5 rad/s, find the angular velocity, wp of = the planet gears and ws the sun gear. ως d) What if the planet gears are held fixed, Wp = 0 ? Шр WR R P WS 80 mm 40 mm 40 mm A
The following diagram shows a piston moving in a cylinder with rod AB. Point B is rotating clockwise with an angular velocity of w. cylinder piston A connecting rod crank bearing B ResearchGate The motion of B is given by the equation r = C cos(wt) + Dsin(wt) Were r is the horizontal +vertical distance of B from O, and C, D are constants. For C=D=42mm and w = 20 rad/s. (i) Write r in the form Rcos (wt ± ß) and state the amplitude and period of r. (ii) Sketch one complete cycle of r. (iii) Explore the differences between the derived form and drawn form
1. A pancake body rotates about a fixed origin. Relative to that origin, a point A at FA = az on the object has instantaneous velocity VA = voŷ. At the same instant, a point B at FB = ay has instantaneous velocity UB = -002. (a) What is the angular rotation vector at that instant? (b) What is the velocity of point C at the location c = (+2)? 2. Find the angular momentum vector (magnitude and direction) of the point C in Problem 1 with respect to point B, assuming the point C has a mass m.
A rod of length L = 2 m slides against a wall as shown in Figure. The velocity of point A is given = 5 m/s. Determine the angular velocity of rod AB and the velocity at point B. OPTION:(multi correct(May Be)): 1.Velocity at point B is near about 12 m/s 2.Angular Velocity of rod AB is about 5 rad/sec 3.Angular Velocity of rod AB is about 7 rad/sec 4.Velocity at point B is near about 9 m/s 5.Angular Velocity of rod AB is about 3 rad/sec 6.Velocity at point B is near about 6 m/s 7.Velocity at point B is near about 3 m/s 8.Angular Velocity of rod AB is about 9 rad/sec
2. Locate the instantaneous center for bar BC. Use it to find the velocity of point C. 6 ft 3ft o=2 rad/sec o-3 rad/sec 6.5 ft Used with permission from "Engineering Mechanics: Dynamics." McGil/King, 4th Ed., 2003 The IC for bar BC is located on a line extended from point A to point B. 4 feet to the right of point B. vc= -9i – 12) ft / see The IC for bar BC is located at point A. ic= -9i - 123 fti sec The IC for bar BC is located on a line extended from point A to point B. 3 feet to the left of point B. vc -6i ft/ sec None of the above
Find the velocity of point B and angular velocity in link 3 using relative analysis and polygon method. Note the drawing is not in scale. B 02 @2=1 rad/s 2 30° A 1 3 4 04 02A=4" AB=7" 0204-=9" 04B=8"
PROBLEM 2 For the mechanism, shown on the figure, Onc = const 5 s'. O4=BC D0,3 m, AB-0,6 m. Determine: a) velocity and acceleration of the point B: b) angular acceleration of the body BC: c) angular velocity and angular acceleration of the body OA: d) linear velocity and acceleration of the pointA. 120 60°
For the position shown where @ =53°, point 4 on the sliding collar has a constant velocity of v-1.25 m/s in the direction shown. At this instant BD is horizontal and DE is vertical. a) Find the velocity of point D and angular velocity of link DE by using instantaneous center of zero velocity, b) Find the angular acceleration of link BD and DE. 00 mm 10H 1Pomm
This problem must be solved using the method of Instantaneous Center of Zero Velocity (IC method). 1) Find Va, VB, and wz when Link 2 = 2, Link 3 = 6, offset = -3, 02 = 60°, w2 = 8rad/sec 2) Find VA, VB, and wz when Link 2 = 3.5, Link 3 = 10, offset = 1, 02 120°, w2 = 8rad/sec 03 B Y Link 3 A Offset Link 2 02 04 = 90° %3D X 02 Slider position d
Unlike the common V6 engine, Subaru engines contain pistons that are horizontally opposed (see Wikipedia for more info). Luckily for us, this also makes for an interesting dynamics problem! At the instant shown, the crank arm's angular velocity is waB = 2,000 rpm (rotating clockwise) and the angle 0 = 40° with respect to the horizontal. Length of bar AB is r1 = 3 in. and the length of bar BD is r2 = 8 in. a) Clearly define coordinate systems for each link and write transformation arrays for each. b) Compute the velocity of point B in ft/s. Express your answer in rectangular coordinates. [Ans. to Check: 33.66 i– 40.11 j ft/sec] c) Determine the magnitude of the speed of the piston P in ft/s. Note: all answers should be positive since we only want to know the magnitude of the speed, not the direction (the piston can only move in the horizontal direction). [Ans. to Check: 43.6 ft/s] r2 10 B