A is rotating in the counter-clockwise direction at a speed of 180 r.p.m. increasing at the rate of 50 rad / s ^{2}. The dimensions of the various links are as follows: OA = 180 mm ; CB = 240 mm ; AB = 360 mm ; and BD = 540 mm. For the given configuration, find 1. Velocity of slider D and angular velocity of BD, and 2. Acceleration of slider D and angular acceleration of BD. do it step by step please

Q: 3. For the crank-slider type linkage shown, joints B and Y are coincident. Link AZ rotates as the…

A:

Q: 83 AE = 8 cm AB = BC=CD=DE=6 cm 02=120° Os =1 rad/sec Os = 90° 02= 2 rad/sec Find the acceleration…

A: Given data,   crank AB=2 rad/sec   ED=1 rad/sec.   AE=8cm   AB=BC=CD=DE=6cm    θ2=120°    θ5=90°…

Q: Motor is driving a gear attached to the linkage in the mechanism as shown: Let r₁ r₂ = 10mm; c=…

A: r1 = r2 = 10 mm (radius of both gears)c = 22 mm (crank length)b = 100 mm (connecting rod length)a =…

Q: The disks in Figure 1 roll on the plane surface without slipping. The left disk rotates in a…

A: Sketching the direction of the velocity of the left end of the bar, The direction of velocity is…

Q: rad The rod OA rotates clockwise at a constant angular velocity of = (3) - Two pin-connected slider…

A: given data is

Q: 1. Write the loop closure equation. 2. Find the position of point A as function of 0, with link AB =…

A:

Q: 1. The diagram below shows the generalised model of the fixed wheel as covered in the course: Robat…

A: Solution: Given Data: l=3 α=3π4β=π4r=4

Q: For the problem related to Fundamental.4, a sketch of the considered system showing and naming (or…

A: Given data : The radius rA=3 in Radius rB=64 in The distance of point P =7 in vp=21 ins , t=5 s…

Q: 1. velocity of F, 2. velocity of sliding of C

A: Solution :-  Given data :- vAO = 130 rpm ωAO = 2π × 13060= 133π Since the length of crank OA = 100…

Q: The mechanism shown below consists of a crank AB (the blue part) and a slotted L- shaped link (the…

A: given data ,                     θ =30°,                   αAB=10 rad / s2…

Q: a) In given figure below for the position shown, calculate angular accelerations for both linkages…

A:

Q: Consider a mechanism shown in Figure 1. The rod AB is rotating about the z axis with an angular…

A: Given data: The angular velocity of rod AB is ω1 The angular acceleration of rod AB is ω˙1 The…

Q: Given the pulley system with block A and a pull down motion at point B at 6 m/s, determine the…

A: (a) and (b) and (c) Consider the diagram as shown below for the given system.

Q: a) An inline crank-slider linkage mechanism is given in Table Q4. Table Q4a Length (mm) Link AB , R…

A: given; radius of crank AB (r)=50mmlength of connecting rod(l)=80mmcurrent position…

Q: Q2: The four-bar linkage mechanism O₂ABO4 shown in Figure 2 is driven by link O₂A at w₂ = 45 rad/s…

A: The length of links are The angle is The angular velocity of  is

Q: The :Q4 = 26 in.; CBE = 27 in. represents a crank and rocker m used in a certain type of wool-…

A: To given thatQ2B=5in                  Q2Q4=26inBC=15in                   CBE=27inQ4C=21in…

Q: Q4/ In a mechanism as shown in Fig. below, the crank OA is 100 m long and rotates in a clockwise…

A: Given DataBC=0.2mCD=0.2mDE=0.25mOA=0.1mAB=0.3mω=100 rpm

Q: Two flywheels of negligible mass and different radii are bonded together and rotate about a common…

A:

Q: A 10-cm diameter pipe is covered by 2 layers of lagging. The inside layer is 4 cm thick and has a…

A:

Q: The Link at AB rotates with an angular velocity of Wab to move piston C. da B OAB di A d1 = 0.4m d2…

A: For solution refer below images.

Q: In the figure shown, If ve=500 mm/s, solve for the (a) velocity (in m/n) of D and (b) the angular…

A:

Q: Mechanism Another of the doohickeys analyzed by the Enthusiast Club is the crank-slider shown. The…

A:

Q: ft ABL 0 0.75 ft P

A:

Q: A uniform slender rod is connected to a thin plate as shown. The rod has a weight of 10lb and the…

A: To calculate the angular acceleration of the uniform slender rod shown in the question, we must…

Q: Shown below is a 4-bar linkage. Assume the tangential velocity at B is vg, and the lengths of the…

A:

Q: You are working as the design engineer in Pacific Robotics and you are to design a robotic arm for a…

A: Givenat θ=35°θ˙ =12°/sr=0.65mr˙=0.29m/sr=-0.25m/s2¨

Q: move to the left Can you sce what happens to le motion of the conneting Tod at that point? You can…

A: it is the case of inversion of four-bar mechanism. it is the model representation of single piston-…

Q: A compressor requires 120 kW to run a: 240 rpm from an electric motor of speed 750 rpm by means of a…

A:

Q: Problem 2 For the mechanism shown if link AO1 = BC = 50 mm, AC = 200 mm, BO5 = 100 mm, and link A01…

A: problem 2:Given:A01=BC=50 mm, Ac=200 mm,B05=100 mmlink A01,rotates at 200 rpm ccw1.Draw velocity and…

Q: ratio of time for forward motion to that for return motion.

A: Given; A quick return mechanism shown in figure.Cranks OA rotates clockwise uniformly OA=2 cmOO'=4…

Q: P4.23, determine (a) the angular velocity of link 3 (b) the velocity of point C Use a complex number…

A: ro2b=5 cm=arbc=6 cm=crbd=10cm=b displacement1......aeiθ2+beiθ3=xvelocity…

Q: Problem 7 (Use relative motion analysis): The four-bar linkage is a famous one! If the angular…

A:

Q: Unlike the common V6 engine, Subaru engines contain pistons that are horizontally opposed (see…

A: Given: The angular speed of AB, wAB = 2000 rpm The angle, θ = 40° The length of bar AB, r1 = 3 in…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.