0.6 m B 0.4 m WAB

Q: The bar shown in the figure is rotating in the counterclockwise direction with an angular velocity…

A: Draw the diagram for the problem. Here, rA and rB are the distances of points A and B from the…

Q: Q5: For the epicyclic gear train shown below. The pitch diameter of the sun gear is 12mm. The pitch…

A: Gears: Gears are the rotating parts of the machine which have tooth cut on them around cylindrical…

Q: 4. Use the relative velocity method and the instant centers method to determine the angular velocity…

A: TO FIND: (1) Angular velocity of rocker by instant center method. GIVEN: Angular velocity of crank…

Q: A mechanism as shown below has the following dimensions: OA = 1.5 , ВС — 600тm ; СD %3 200тт , AB…

A:

Q: 50 mm

A: Given that, rA=50 mm,rB=100 mm,rC=150 mm,NA=600 rpm,rB'=50 mm, Calculate angular velocity of gear…

Q: 0.25 m B 32° AB= 15 rad/s 0.5 m DO 0.25 m

A: A) Instantaneous centres of a given mechanism  Ans: The instantaneous center of link BC i.e. 3 is…

Q: 3.7 Fig. 3-8 shows a cam mechanism. AB =1, the radium of the cam is R,OA = h, LOAB = 90°, the angle…

A:

Q: Question No #06: Analyze the telescoping link AB at the instant represent and determine its angular…

A:

Q: 12. The gear A on the drive shaft of the outboard motor has a radius r = 0.5 in. and the meshed…

A: given; radius of propeller shaft(rB)=1.2 in…

Q: 60° 45° 3. The crank OA of the offset slider-crank mechanism rotates with a constant clockwise…

A: To find angular velocity of link AB

Q: Original Question: The figure below represents a pair of bevel gears A and B. Gear A rotates in a…

A: Given:The angular velocity of member OC is equal to the angular velocity of gear B because gear A is…

Q: Point C of the mechanism shown in Figure has a velocity of 14 in/s to the right. Using the method of…

A:

Q: The hydraulic cylinder is extending with the velocity and acceleration shown (Egute.1) Figure 7p-2mA…

A: To Find :  The angular acceleration of crank Ab and BC at instant shown. Given : The velocity of…

Q: Gear 2: N2 = 25 teeth and Pd = 20 per in Gear 3: d3 = 3.5 in Gear 4: N4 = 28 teeth Gear 5: d5 = 4…

A:

Q: 1. Angular velocity of links BC and CD. 2. Angular acceleration of links BC and CD.

A:

Q: Problem 3: The crank AB is rotating with a constant angular velocity of 3 rad/s about the fixed…

A: The schematic diagram of the given system is From figure, AC=600 mm AB=300 mm θ=25° Angular…

Q: The instant shown crank BC has a constant angular velocity of 42 rpm clockwise.a)Determine the…

A: Please refer below pages.If you have any doubts please feel free to ask. Explanation:Step 1:

Q: Crank OA rotates with a counterclockwise angular velocity of 8.1 rad/s. By the method of this…

A: The angular velocity of crank OA is

Q: For the instant represented, when crank OA passes the horizontal position. Crank OA has a uniform…

A:

Q: For the shown position of the crank-shaft mechanism it is known that =95, =3 . OA=R=0,1 m, ZBOA=90 H…

A:

Q: pic: Relative Motion Analysis: Acceleration Gear A  is between a stationary gear rack  F and the…

A:

Q: L. = = 10

A: The angular velocity of member OC is equal to the angular velocity of gear B because gear A is…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: b = 8 in ωA = 6.2 rad/s

Q: QUESTION 2 The crank arm AB of an engine rotates around point A with an angular velocity of 6 rad/s…

A:

Q: A kinematic diagram of slider crank mechanism is shown in the following figure. The crank rotates at…

A:

Q: The ABD arm is pinned to a B-collar and DE handle. If the angular velocity of the crank DE rotates…

A:

Q: In the graphic below, Gear A begins at rest and is given an angular acceleration clockWise of a = 3t…

A: Given:α=3trA=6 inrB=2 inrc=4 inrD=1 in

Q: 12. The gear A on the drive shaft of the outboard motor has a radius r = 0.5 in. and the meshed…

A:

Q: Wheel A has a radius of 280 mm, wheel D has a radius of 190 mm, and the length of link BC is 500 mm.…

A:

Q: ram above, RA = 0.339 m, while Rg = 0.776 m. A and B are intermeshing gears (I just u the teeth)…

A:

Q: In the following mechanism the angular acceleration of gear A is aa = (0.203 + 0. 5) rad/s2. If its…

A:

Q: The disk has an angular acceleration a = 7 rad/s and angular relocity w = 3 rad/s at the instant…

A:

Q: The planetary gear train shown in the image below has 16 teeth on the sun and 23 teeth on the…

A:

Q: 5. Gear A (TA = 100 mm) is rotating clockwise at 1200 rpm as shown below and is accelerating with a…

A: Given data with suitable variable is shown below. rA=100 mmNA=1200 rpmαA=1.5 rad/s2rB=175 mm   (a)…

Q: find the accelerations of points A and D, if point O's velocity is 3ft/sec to the right and point…

A: Given:The velocity of point O to the right, The acceleration of point O to the left, The radius of…

Q: (b) Referred to Figure 2 if piston D is moving at velocity 10 m/s and acceleration 1 m/s? in…

A: Angular velocity is the rate of change in angular position of the object and it is denoted by the…

Q: 4. A cart is moving to the left at 2 m/s. It is braking at 6 m/s² (i.e acceleration vector opposes…

A:

Q: he figure below represents a pair of bevel gears A and B. Gear A rotates in a horizontal plane about…

A: The gear A is stationaryThe angular velocity of OC is

Q: The bar BC in the figure (Figure 1) rotates with an angular velocity w = 6 rad/s and an angular…

A:

Q: n the mechanism shown in Figure 3, link OA has a length of R = 0.5 m. Link AB has a length of L =…

A: For the solid please refer below images

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.