Consider a noiseless channel need to carry human voice and to be transmitted with four signal levels only. Then; (a). Calculate the maximum bit rate. (b). Consider the same noiseless channel transmitting a signal with four signal levels (for each level, send 3 bits). (c). Compare the results obtained in a. and b.

Consider a noiseless channel need to carry human voice and to be transmitted with four signal levels only. Then; (a). Calculate the maximum bit rate. (b). Consider the same noiseless channel transmitting a signal with four signal levels (for each level, send 3 bits). (c). Compare the results obtained in a. and b.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter17: Commercial And Industrial Air-conditioning Control Systems

Section: Chapter Questions

Problem 25RQ

See similar textbooks

Similar questions

1. With the help of Octave program perform the Modulation and Demodulation (AM) of information signal with carrier signal, through subplots with following signals a. Modulating signal b. Modulated signal c. Demodulated signal
See the figure below for Manchester scheme on CH-1 of Scope. Write the corresponding input bit stream. DE
Consider error control methods in digital signal transmission. Assume Hamming code is used with even parity. (a) Assume the received code word is 1110101001, determine if the code word is correct. If no, identify the wrong bit and obtain the original data word. (b) If the analogue signal before digitalisation is of frequency from 200 Hz to 1.5k Hz. What is the lowest sampling frequency? (c) Following (a) (b), determine the bandwidth requirement for transmitting the digital message.
A 450 kHz carrier signal is modulated with a 15 kHz modulating signal. What are its sideband frequencies?
3.) List three gains or losses that could be modified (and how) to increase the signal-to-noise ratio in a communication signal.
What are the data rate limits? Calculate the maximum bit rate of noiseless channel with a bandwidth of 4000 Hz transmitting a signal with three signal levels.
Q24)This multiple choice question from DIGITAL COMMUNICATIONS course.just write for me the final answer. The choice of the number of bits per PCM word depends on the a. SNR b. Bandwidth c. None of the mentioned d. SNR and bandwidth
Exauple: A Television signal having a bandwidth of 4.2 MHz is transmitted using binary PCM system. Given that the number of quantization levels is 512. Determine: Code rate length Transmission bandwidth Final bit rate Output signal to quantization noise ratio i) ii) iv)
3. Some GPS receivers use 1 bit ADCS (Analog-to-digital Converters) to sample and quantize the signal i.e. the output of the ADC is simply 2 quantization levels: -1 or +1. This is typically done to save on power. (a) What is the quantization SNR? How does it compare to typical thermal noise SNR of a GPS signal before correlating with the CDMA code? (b) Justify, how come it is possible to sample the signal using a single bit and still get good performance.
Answer all questions below: 1. Draw the general block diagram of Frequency Division Multiplexing (FDM) 2. Multiplexing is a technique that allows the (simultaneous) transmission of multiple signals across a single data link. Figure Q2 below shows a multiplexer with four 500 kbps data stream inputs and 1 data stream output where the unit of data is 1 bit. Determine: i. ii. iii. 500 kbps The type of multiplexing technique used. The input bit duration. The output bit rate. 500 kbps 500 kbps. 500 kbps. ... ... ... 1 0 1 0 1 0 1 0 0000 1 1 1 1 0 1 0 0 MUX Figure Q2 Frames 0101 0001 110100010101
- Determine the number of errors that can be detected and corrected for data values with a Hamming distance of (a) 3. (b) 4.
Q4: Show how to PSK modulate and demodulate the data sequence (01101). Assign two full cycles of carrier signal for every data bit. Explain the steps in details and plots.