Exauple: A Television signal having a bandwidth of 4.2 MHz is transmitted using binary PCM system. Given that the number of quantization levels is 512. Determine: i) Code rate length Transmission bandwidth ii) Final bit rate Qutput signal to quantization noise ratio
Q: reversed in 0.02 s.
A: We need to find out induced emf for given inductance .
Q: study of electromagnetism? Choose two. kinematics dynamics magnetism
A: Electromagnetism is one of the main part of electrical engineering.
Q: Explain what happens when a dielectric leakage occurs.
A: A dielectric material is an insulator and ideally shouldn't allow any current through it But sometim...
Q: which section of the overload relay is typically connected to voltages that range from 120 to 600 vo...
A: "CURRENT SENSING SECTION" of the overload relay is typically connected to the voltages that range fr...
Q: 0-100mAdc mA 1K 20Vdc R, IK
A: As per the guidelines given to us, we can only provide the solution of first three subpart in multi ...
Q: H.W. (3) The current through a 100 mF capacitor is given. Find the sinusoidal expression for the vol...
A: In this question, We need to calculate the voltage across the capacitor We know Current in the ca...
Q: 04. Find the total resistance for the configuration in Fig. 4 R, 20 Rr R2 20 R3 R
A:
Q: H.W: Find (HPBW) and (FNBW), in radians and degrees, for the following normalized radiation intensit...
A: It is given that: (a) Uθ=cos2θ(c) Uθ=cos2θ cos3θ
Q: Q5 A 20 KW, 250 V d.c. shunt generator has armature and field resistance of 0.1 Q and 125 O respecti...
A: As our guidelines we are supposed to answer only one question. Kindly repost other question as saper...
Q: Calculate the Laplace transform f (t) = t- 3e-2t
A: This question belongs to basic electrical . It is based on the concept of calculation of Laplace tra...
Q: 1. The closed-loop transfer function of a control system has a denominator polynomial equals to s + ...
A:
Q: The region in which 4 <r< 5, 0< 0 < 35°, 0.6m < Ø< 1.2n contains the volume charge density of p, = 1...
A: The solution is given below
Q: Find Roc 10Ω a 3Ω 6N bo- 102
A: In this question, We need to determine the equivalent resistance across the terminal b and. C. We ...
Q: If the time period of output voltage of a 1-o bridge rectifier is 25/3 ms, then the supply frequency...
A: Given: A single phase bridge rectifier having, The time period of the output voltage, T = 253 ms
Q: Oppgave 1 Bestem om komponentene er resistans, spole eller kondensator. Finn også verdien av C, L og...
A: As per our company guidelines we are supposed to answer only first 3 subpart kindly repost other par...
Q: Are the operators below stable or unstable?Motivate answer. your it is stable, is'it underdamped or ...
A:
Q: What is the magnitude of the simple gain term for the following open loop transfer function: 24 G(s)...
A:
Q: H2 RCS) G2 G3 Gy -YCS) Simplify the following using Suitable Rules. block diagram
A:
Q: [Q2] A short dipole antenna with a uniform current distribution in free space of 3 A at frequency of...
A: The Poynting vector denotes both the propagation direction and the energy flow density, or intensity...
Q: determine the average value and the rms of the waveform
A:
Q: The maximum flux density in the core of a 250/3000V, 50Hz single phase transformer is 1.2 Wb/m2 . If...
A: This question belongs to electrical machine . It is based on the concept of induced e.m.f. in a sing...
Q: Graph: Take a graph sheet and divide it into 4 equal parts. Mark origin at the center of the graph ...
A: According to the question, for the given data as shown below We need to plot the V-I characteristic...
Q: 4700R1 V ( 2V, at 10 kHz. 10 mH 3L1 10Ω R3 Calculate the peak current voltage across R1 phase angle ...
A:
Q: the largest overload heater is ____ amperes.
A: Overload heaters are also known as Overload Relay Heater. There are four different classes of heater...
Q: An electric motor having a power factor of 0.69 draws a current of 18.9 A from a 220 V, 60 Hz source...
A: Given, An electric motor having Power factor, cosθ=0.69 Current, I=18.9 A Supply voltage, V=220 V Fr...
Q: 3. Three loads A, B and C are connected in series to a 110-volt source. Load B takes 1100W, load C t...
A: The solution is given below
Q: 2. Use nodal analysis to determine the node voltages for the circuit. R4 5 A R3 ЗА
A:
Q: Find the coefficient of coupling between two coils whose mutual inductance is 1 H and self-inductanc...
A: From the question, it is given that Mutual inductance (M)=1 H Self-inductance of coil 1 (L1)=1.2 H S...
Q: P D1 Q1 D2 Q2 Q CLK G1 Q1' G2 Q2'
A: The output P will follow in only positive clock with delay T. The output Q will follow P
Q: What is fc for the filter in the below circuit? R= 293 0, L=9 mH, and Vin = 7 V The result should be...
A:
Q: In a 400 V, 50 c/s transformer, the total iron loss is 2500 W. When the supplied p.d. is 220 V at 25...
A:
Q: Two resistors are to be combined to form an equivalent resistance of 1,000 n. The resistors are take...
A:
Q: Tutorial Problems No. 1 Q1 A250 v shunt motor takes a total current of 20 A. the shunt field and arm...
A:
Q: a. Find an equivalent generalized transition graph with only two states. b. What is the language acc...
A:
Q: You've been asked to bias the BJT shown below to set VB=(1/3) VCC, and VC=(2/3) VCC while the collec...
A: According to the question, we need to find the voltage gain of the circuit shown below
Q: Q4: The continuous - time synal x.lt) hac -the Fourier tansfrm skoun be low: Signal ralt) is sanpled...
A: Multiplication of signals in time domain is convolution of that signals in frequency domain. Prerequ...
Q: Three similar choke coils are connected in star to a 3 phase supply. If the line current are 15 A, t...
A: Given,Line current IL = 15AActive Power P = 11 KWApparent power S = 15 KVA Line voltage VL =S3×IL =1...
Q: Find the coefficient of coupling between two coils whose mutual inductance is 1 H and self-inductanc...
A:
Q: which type of overload relays connect a coil in series with the conductors supplying power to the mo...
A: "Thermal overload relays" connect a coil in series with the conductors supplying power to the motor....
Q: Three similar choke coils are connected in star to a 3 phase supply. If the line current are 15 A, t...
A:
Q: A point charge 5nC is located (2,0, 4) and a point charge -2nC is located at (–3,0,5). Find É at (1,...
A:
Q: A 400-ohm resistor, a 20-uf capacitor, and a 0.505-henry inductor are connected in parallel and are ...
A: The solution is given below
Q: 5. Three non-inductive resistances, each of 100 ohms are connected in star to 3 phase, 440 V supply....
A: In this question, We need to determine the line current and power factor? We know Current I= V/Z P...
Q: Q6 A 250 V shunt motor on no-load runs at 1000 r.p.m. and takes 5 A. the total armature and shunt fi...
A: Note: We are authorized to answer the first question since the exact one wasn’t specified. Please su...
Q: 9A 100 h.p.. 500 v shunt motor ha
A:
Q: Given the system transfer function T (s) s(3s+2) (s²+10s+25)(s²+2s+5)' what is the steady state phas...
A: The solution is given below
Q: A uniform phased array of 6 isotropic elements, placed at a distance 1/2 apart, is intended to recei...
A: Phase Difference: The difference between two phases are called Phase differences. The phase differen...
Q: Three single phase transformer are balanced delta delta each rated 120 kVA supplying a 3 phase load ...
A: The transformer has a primary and a secondary side. It converts electrical power to electrical power...
Q: Given a set of capacitors: 7 nF, 6 nF, 5 nF, 4 µF, 3 pF and 10 µF, solve the following problems: a. ...
A:
Q: Given the point D(−4, 5, 3) and A = yax + (x + z)z ay, express the D and A in Spherical Coordinate S...
A:
Step by step
Solved in 2 steps
- Q2/ The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of ±0.1% (full scale). The analog voltage waveform has a bandwidth of 100 Hz and an amplitude range of -10 to +10 volts. Find the minimum sampling rate required. i) ii) Find minimum bit rate required in the PCM signal. Find the number of bits in each PCM word. iii) iv) Find the minimum absolute channel bandwidth required for the transmission of the PCM signal.Problem 2: The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of ± 0.1 % of the peak-to-peak analog signal. The analog voltage waveform has a bandwidth of 100 Hz and an amplitude range of – 10 to + 10 Volts. Determine the minimum sampling rate required. b. Determine the number of bits in each PCM word. c. Determine the minimum bit rate required in the PCM system. d. Determine the minimum absolute channel bandwidth required for the transmission of the PCM signal.The information in an analog voltage waveform is to be transmitted over a PCM system with a 10.1% accuracy (full scale). The analog waveform has an absolute bandwidth of 100 Hz and an amplitude range of -10 to +10 V. (a) Determine the minimum sampling rate needed. (b) Determine the number of bits needed in each PCM word. (c) Determine the minimum bit rate required in the PCM signal. (d) Determine the minimum absolute channel bandwidth required for transmission of this PCM signal.
- Choose the correct answer low HDOP (Horizontal Dilution of Precision) number such as2 indicates a ........................... a.poor fix b.good fix c.poor signal quality d. good signal quality4. The information in an analog voltage waveform is to be transmitted over a PCM system with a F 0.2% accuracy (full scale). The analog waveform has a bandwidth of 200 Hz, and an amplitude range of -5 to +5 V. determine the following: - The minimum sampling rate needed. - The number of bits needed in each PCM word. - The minimum bit rate in the PCM signal. - The minimum channel bandwidth for transmission of this PCM signal.The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of : 0.1 % of the peak-to-peak analog signal. The analog voltage waveform has a bandwidth of 43 Hz and an amplitude range of - 10 to 10 Vots. Determine the minimum bit rate fin bps) required in the PCM system? O a 688 O 774 O c 387 O d 86 Oe 258
- 1. With the help of Octave program perform the Modulation and Demodulation (AM) of information signal with carrier signal, through subplots with following signals a. Modulating signal b. Modulated signal c. Demodulated signalThe information in an analog waveform, whose maximum frequency fm-D4000HZ, is to be transmitted using a 16-level PAM system. The quantization must not exceed +1% of the peak-to peak analog signal. (a) What is the minimum number of bits per sample or bits per PCM word that should be used in this system? (b) What is the minimum required sampling rate, and what is the resulting bit rate? (c) What is the 16-ary PAM symbol Transmission rate?H.w do H.W: Compute the binary code word values for the amplitudes 0.4 V and 0.78 V, then compute the quantization error for each. Suppose you have a 2bit ADC (PCM) modulator with 0 to 1 volt amplitude signal as shown below: 1 V OUANTI7ATION LEVELS.
- 4. This problem addresses the digitization of a television signal using pulse-code modulation. The signal bandwidth is 4.5 MHz. Specifications of the modulator include the following: Sampling: 15% in excess of the Nyquist rate Quantization: uniform with 1024 levels Encoding: binary Determine (a) the Nyquist rate, and (b) the minimum permissible bit rate.An analog signal with a bandwidth of 4.2 MHz is to be converted into binary PCM and transmit- ted over a channel. The peak-signal quantizing noise ratio at the receiver output must be at least 55 dB. (a) If we assume that P=0 and that there is no ISI, what will be the word length and the number of quantizing steps needed? (b) What will be the equivalent bit rate? (c) What will be the channel null bandwidth required if rectangular pulse shapes are used?. What are specifications of Digital modulation techniques?