Answer all questions below: 1. Draw the general block diagram of Frequency Division Multiplexing (FDM) 2. Multiplexing is a technique that allows the (simultaneous) transmission of multiple signals across a single data link. Figure Q2 below shows a multiplexer with four 500 kbps data stream inputs and 1 data stream output where the unit of data is 1 bit. Determine: i. ii. iii. 500 kbps The type of multiplexing technique used. The input bit duration. The output bit rate. ... 500 kbps 500 kbps. 500 kbps- ... 1 1 0 0 1 0 0 0 1 000 1 1 0 1 1 0 0 MUX Figure Q2 Frames 0101 0001 1101 00010101

Answer all questions below: 1. Draw the general block diagram of Frequency Division Multiplexing (FDM) 2. Multiplexing is a technique that allows the (simultaneous) transmission of multiple signals across a single data link. Figure Q2 below shows a multiplexer with four 500 kbps data stream inputs and 1 data stream output where the unit of data is 1 bit. Determine: i. ii. iii. 500 kbps The type of multiplexing technique used. The input bit duration. The output bit rate. ... 500 kbps 500 kbps. 500 kbps- ... 1 1 0 0 1 0 0 0 1 000 1 1 0 1 1 0 0 MUX Figure Q2 Frames 0101 0001 1101 00010101

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter17: Commercial And Industrial Air-conditioning Control Systems

Section: Chapter Questions

Problem 25RQ

See similar textbooks

Similar questions

1. With the help of Octave program perform the Modulation and Demodulation (AM) of information signal with carrier signal, through subplots with following signals a. Modulating signal b. Modulated signal c. Demodulated signal
Data communication subject , i need now fast less than 5 m
3. What is the type of demodulation we used to demodulate SSB signal (part-A). Explain your answer.
A 450 kHz carrier signal is modulated with a 15 kHz modulating signal. What are its sideband frequencies?
• The input to the Encoder is (1), _lines and the output is (2) _lines. • The input to the Decoder is (3). input lines and (4)_ output lines. The multiplexer has (5), output and (6). _inputs.
Please help Cs
3. Which of the following is a key characteristic of orthogonal frequency-division multiplexing?A. Amplitude modulationB. Noise performanceC. Digital modulationD. Spectral efficiency
To implement 8-to-1 line multiplexer using two 4-to-1 line multiplexer(MUX): O a. The third selctor is connected to the enable line of the first and second MUX. O b. Only the enable line of the first MUX must be connected dirictly to the enable for the second MUX. O c. The third selctor is connected to the enable line of the first MUX which is connected through inverter to the enable of the second MUX. O d. All inputs lines for the first mux must be connected to the input lines for the second mux.
Consider error control methods in digital signal transmission. Assume Hamming code is used with even parity. (a) Assume the received code word is 1110101001, determine if the code word is correct. If no, identify the wrong bit and obtain the original data word. (b) If the analogue signal before digitalisation is of frequency from 200 Hz to 1.5k Hz. What is the lowest sampling frequency? (c) Following (a) (b), determine the bandwidth requirement for transmitting the digital message.
. What are specifications of Digital modulation techniques?
3. Explain disadvantages of ASK modulation system.
Explain frequency hopping acquisition scheme using a simple PN sequence. Assume that the length of PN sequence is 15 and the number of frequency hopping levels is 8