A series circuit of RLC with following parameters, R=15 ohm, L-20 m H Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram & C=100 micro

A series circuit of RLC with following parameters, R=15 ohm, L-20 m H Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram & C=100 micro

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
A series RC circuit with R=4k ohms and C= 0.40 mF is connected to an AC voltage source e(t)= 100 sin200t. Determine the following: a). The overall power factor ( indicate big leading or lagging) b). The voltage drop across the resistor and the capacitor
ESSAY: Describe what happens to the power in this RLC series circuit as the capacitance decreases. Explain in general terms why the observed change should occur. Understand the effects of basic electrical components on the average power of the system and the concept of power factor. Differentiate between average power and real power.
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
A load is rated at 440V(rms), 7.5A(rms) and 3.3KW when connected to a 50HZ source. Find the load impedance.
Quistion.4. a) A sinusoidal voltage is applied to the resistive circuit in figure.Q.4. a. Determine the following: i. Ims ii. Iavg iii. Ip iv. Ipp 10V 1.0 ΚΩ Figure.Q.4.a
A 220 Ω resistor is in series with an 80 mH inductor. The AC source is 48 at 1 kHz. The power factor is ________. Hint: Draw the circuit and get Vs and Is
15. You are working on a power factor correction installation, and you notice with a clip-on ammeter as you add in capacitance the current drops, you add more capacitance and the current drops, you add more capacitance the current rises. How do you know when you are at unity power factor?
7 Find the average and effective values of voltage for sinusoidal waveform shown in Figure. Vm = 100 V 2x x14 9714 [Ans: 27.17 V, 47. 67 V]
"If lab is equal to 595.8252306 and lb is 344296, the phase sequence is:" O POSITIVE O NEGATIVE