Three Impedances each of (8 - j24)N are connected in mesh across a three-phase 420V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. phase current (Ip)

Three Impedances each of (8 - j24)N are connected in mesh across a three-phase 420V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. phase current (Ip)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please explain in detail. A. In a series circuit, if the AC voltage is measured across the AC voltage source, will there be any variations in the phase of the AC voltage across each resistor from the measured AC voltage across the source? B. In an AC voltage source, why does voltage vary with time? Please explain in detail. C. In a series circuit, are the frequencies of the AC voltages across each resistor the same? Why is this so? ...
Show plz the solution with the setting of components
How about the average power on each elements? And is it absorbing or delivering power too?
Consider the circuit shown in Figure 1. V1 is a 7.2 kHz sine wave with an amplitude of 4 V.Figure 1: RC Circuit Schematic1. Determine the total impedance (Z) of the circuit.2. Using V1 as a zero-phase reference, calculate the values of the following:a) Amplitude and phase of current (I)b) Amplitude and phase of voltage across R1 (VR1)c) Amplitude and phase of voltage across C1 (VC1
Given the circuit shown, answer the following questions I 40 8n I3 Vs = 24/60° v E V2 -j4 n 12 one of the following statements is correct: Choose... 12 in Ampere equals to: Choose... the equivalent impedance in Ohm of the circuit is Choose... V2 in Volts equals to: Choose...
What is the average power in ghe single phase ac circuit with the purely resistive load? It is sinusoidal steady state excitation.
Please show your detailed solution
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
Clear and correct or dislike
Need asap
choose the correct option for ac circuit
If T = 0.6Z – 60° and A = 48cm find the position of the first voltage minimum on the line. Select one: O a. The first voltage minimum is at 2cm from the load. O b. The first voltage minimum is at 72cm from the load. O c. The first voltage minimum is at 8cm from the load. O d. The first voltage minimum is at –4cm from the load. O e. The first voltage minimum is at 20cm from the load. O f. The first voltage minimum is at 32cm from the load. O g. The first voltage minimum is at 44cm from the load. O h. The first voltage minimum is at 24cm from the load.