In a series circuit containing pure resistance and pure inductance, the current and voltage are expressed as: i(t) = 5 sin (314t + )and v(t) = 15 sin (314t + "). a) what is the impedance of the circuit, b) what is the value of the resistance, c) what is the inductance in henry's, d) what is the average power drawn by the circuit, e) what is the power factor?

In a series circuit containing pure resistance and pure inductance, the current and voltage are expressed as: i(t) = 5 sin (314t + )and v(t) = 15 sin (314t + "). a) what is the impedance of the circuit, b) what is the value of the resistance, c) what is the inductance in henry's, d) what is the average power drawn by the circuit, e) what is the power factor?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Convert the following instantaneous currents to phasors, using cos(t) as the reference. Give your answers in both rectangular and polar form. (a) i(t)=5002cos(t30) (b) i(t)=4sin(t+30) (c) i(t)=5cos(t15)+42sin(t+30)
An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
The real power delivered by a source to two impedances, Z1=4+j5 and Z2=10 connected in parallel, is 1000 W. Determine (a) the real power absorbed by each of the impedances and (b) the source current.
Find the RMS value of V)-100 sin(377t+76) V
15 A of current is taken by a non-inductive load at 125 V. In order that the same current shall be generated from 240 V, 50 Hz mains. An inductor is now also then connected in series. Note: The resistance of the inductor should be ignored and also assume the waveform to be sinusoidal. Determine the phase difference between the current and the applied voltage, the impedance of the circuit and the inductance of the inductor.
2. Refer to the Figure 2. a) Determine the total impedance of the circuit in polar form. b) Determine the voltage v(t) and current i(t) sinusoidal forms. Sketch one cycle of the waveforms in the same x-axis. Clearly indicating the peak value and the period of each waveform and the phase difference (in milliseconds) between the two waveforms. c) Determine the values of resistance R and inductance L. d) Determine the phasors V,, VR and Vc. e) Sketch the phasor diagram showing Vs, Vr, Vr, Vc and I.
d. 565.685 V If a Load absorbs 20 kVA at a leading power factor of 0.6. Then the complex power is: Select one: O a. 12000 - j16000 VA O b.-12000 + j16000 VA O c. 12000 + j16000 VA O d. None of these Given the circuit below and the associated set of voltages and currents, the reactive Power developed by im voltage source is FENG300 MINTERM
A 25ohm resistor is connected in series with a %0 mH inductor. This circuit is connected to a 120V, 50Hz supply. Solve for a. Inductive reactance b. impedance c. S d. P e. Q
A series circuit consisting of 17ohm resistance and 20mH inductane is connected across a 220V(RMS) 60Hz supply. Determine the magnitude of the total current in the circuit.
A sinusoidal alternating voltage has an r.m.s. value of200 V and a frequency of 50 Hz. It crosses the zero axis in apositive direction when t = 0. Determine (i) the time when volt-age first reaches the instantaneous value of 200 V and (ii) thetime when voltage after passing through its maximum positivevalue reaches the value of 141.4 V.
1. Instruction: Provide the correct answer. 1. What is the relationship between the supply voltage and circuit current in purely capacitive circuits?. 2. Vm = 100cos(377t + 75°) transform into sine form is a complex number that represents the amplitude and phase of a sinusoid. 3. 4. What is the phase relationship between a supply voltage and current through a purely inductive circuit?. 5. The rms value of the signal is also called the 6. The It is also the cosine of the angle of the load impedance. 7. When Q < 0, the power factor is 8. The process of increasing the power factor without altering the voltage or current to the original load is known as 9. is the cosine of the phase difference between voltage and current. is the measurement to measure average power. 10. What is the meaning of VAR?